The kitchen is pasted with wall tiles, how to do waterproofing?

1. The waterproof coating is used in strict accordance with the proportion, and the surface is hairy when brushing; Or after the waterproof is dry, use cement to "brush" the wall and then paste the brick;

2. Now there are two main ways to paste tiles, cement mortar or tile adhesive. If cement mortar is used, the cement mortar should not be applied too thickly, and there should be gaps between bricks; If tile adhesive is used, there is not so much attention to detail, because tile adhesive is several times more viscous than cement mortar!

3. Reduce the floor tiles on the wall, some owners hope that their homes can be decorated with personality and more beautiful, and the floor tiles on the wall were once popular, so they also want to do so, however, after all, the floor tiles are paved on the ground, paved on the wall, and it is easy to fall off because the size is too large and the quality is too large.

Waterproofing is done before tiling, and waterproofing cannot be done after pasting.

Waterproof process:

1.The surface of the base layer of the waterproof layer must be cleaned of dust, sundries, etc., and the residual mortar hard blocks and protruding parts on the surface should be shoveled and swept clean, plastered and pressed, and the yin and yang corners should be wiped into arcs or obtuse angles.

2.The surface of the base layer coated with waterproof layer should be kept dry, smooth and firm, and there should be no defects such as hollowing, cracking and sanding.

3.In the screeding layer ground drain, pipe roots, water outlets, sanitary ware roots (edges), to close the head smooth. The slope meets the design requirements, and the components must be installed firmly and embedded tightly. After acceptance.

4.The details such as pipe roots, floor drains, drainage outlets, and yin and yang angles that protrude from the ground should be supplemented with additional layers first, and after brushing the polyurethane primer, the inspection and acceptance of the concealed project should be completed.

5.All kinds of materials used in the waterproof layer, base treatment agents, xylene, etc. are flammable materials, and the storage and storage should be kept away from the fire source, and fireworks should be strictly prohibited during construction and operation.

6.The construction of the waterproof layer shall not be carried out in rainy and windy days, and the ambient temperature of the winter construction shall not be less than 5.

If the ground is waterproofed, the lowest layer of the wall tile can be knocked off, and the tile will be repaired after the ground waterproofing is done.

1. After the wall is made of waterproof coating, we must not be able to directly paste the wall tiles on it, we need to make a protective layer of mortar waterproofing agent on the wall, and we can paste the tiles after the mortar protective layer is completely dry, and the quality of the tiles will be better and better, so that the water absorption rate of the tiles will be reduced, and it is difficult to meet our needs by using the sand cement pasted tiles to be paved.

2. And for the current waterproof coating base is mainly based on the concrete wall, we only need to do a good job of waterproofing before we can paste the tile, but now the market also has a waterproof coating that can be done directly on the tile, but in fact, this method is still unreliable, and there is basically no waterproof effect after the best.

1. If we choose cement mortar waterproof coating, we can actually directly paste tiles on it in this case, but generally in order to achieve better adhesion during our construction, we generally paint a layer of 108 construction glue on the wall and then pave the tiles.

2. When the tile is paved, we generally use cement mortar directly to paste the ceramic tile on the load-bearing wall, but for the flue or the sewer pipe of the red brick package, in order to avoid the situation that the tile falls off in the later stage, we had better draw the wall before the formal tiling, and then we paste the tiles, so as to increase its adhesion.

3. The main purpose of treating the waterproof surface is to prevent the tile from hollowing and falling off, so for the current construction method can also be like this, choose to use the tile paste for the tile paste, which is what we call the thin paste, because the viscosity of the tile paste is relatively large, it can better avoid quality problems, but in this way, the construction cost will increase a lot.

In fact, for the current decoration market, the technology is more reliable, many often appear problems, now in the construction, professional workers and masters will have a reasonable way to deal with it, so when we are constructing, we must find professional construction personnel, we can tell them our questions, so that they can give reasonable solutions according to the actual situation.

The waterproof coating can not be directly pasted with tiles, and the waterproof layer should be covered with 20mm thick 1:3 cement mortar, and then the surface layer or tiles should be pasted.

Hello, about your question I think 1, after the wall is made of waterproof coating, we must not be able to directly paste the wall tiles on it, we need to make a protective layer of mortar waterproofing agent on the wall, and we can paste the tiles after the mortar protective layer is completely dry, and the quality of the tiles will be better and better, so that the water absorption rate of the tiles will be reduced, and it is difficult to meet our needs by using the sand cement pasted tiles used to pave.

2. And for the current waterproof coating base is mainly based on the concrete wall, we only need to do a good job of waterproofing before we can paste the tile, but now the market also has a waterproof coating that can be done directly on the tile, but in fact, this method is still unreliable, and there is basically no waterproof effect after the best.

3. Can you directly paste tiles directly on the waterproof coating, but also depends on our construction quality and material quality, at present, there are cement mortar waterproof coatings on the market, so that the waterproofing can penetrate into the wall well, forming a better waterproof layer, and the adhesion between the surface and the tile is also very good, and it can also prevent mildew.

In fact, you can paste it directly, so that it will not damage the waterproof material, and many decorations are pasted like this, such as the kitchen and bathroom, it is impossible to apply waterproof tiles.

The waterproofing paint can be air-dried and then the tiles can be pasted with a cement mixture.

Waterproof home decoration, the choice of waterproof materials is crucial, and choosing a good waterproof material can make the decoration more effective. The variety, grade and ratio of waterproof materials must meet the relevant standards of environmental protection standards. Does the kitchen wall need to be waterproof?

How is waterproofing done.

Does the kitchen wall need to be waterproof?How to do waterproof It has the characteristics of waterproof, breathable, super soft, crack resistant, transparent, environmental protection, etc., and has obtained the certification of China's ten rings. Waterproof rainbow This waterproof coating can withstand the slight displacement of micro-cracks, cavities, acres and substrates; High-quality breathable waterproofing technology helps the water vapor in the wall to diffuse into the indoor environment, avoiding the adhesion and peeling of mold and waterproofing layers on the wall. It happens, it's a waterproof and waterproof kitchen helper.

It is also suitable for waterproofing and waterproofing floors and walls such as bathrooms, balconies, etc. When will the new house be renewed.

Ratio and dosage: liquid material: powder material = 10: 15 (weight ratio); The thickness of the wall coating film is not less than every square meter of Wusen square meters, and the thickness of the floor film is not less than per square meter. The dose is 3 kg.

How to make a waterproof kitchen - Yuhong waterproof 300 colors ultra-soft waterproof coating construction process.

One, Ingredients: Mix a bag of liquid material with a bag of powder. Does the kitchen wall need to be waterproof?First, pour the liquid material into the mixing tank, slowly add the powder while stirring, and stir evenly without an electric stirrer;

Second, the details of node processing: before spraying a large area, the method of rain plugging must be used to leak parts, such as floor drainage, yin and yang angles, root canals, etc. (the diameter does not affect the back coating), and then use waterproof paint as the node coating;

Waterproof coatings. First, clean the basic layer of soil and lime sand; Before waterproofing construction, the primer should not contain water; It is forbidden to add water;

Second, under normal circumstances, the kitchen is impermeable and 30 cm above the ground. If the kitchen is equipped with solid wood cabinets, it is recommended that the cabinet be 20 cm high. Place a waterproofing layer meters above the walls of the sink and treat the corner areas.

The above is true,Does the kitchen wall need to be waterproof?How to do waterproofing, make a detailed introduction, I hope it can help everyone.

You can get it for free

The kitchen wall can effectively avoid the subsequent wall tiles falling off when the paving is firm, so how can the kitchen wall tiles be firmly pasted? How long does it take to paste the kitchen wall tiles after the waterproofing project? Today, I will answer them one by one for you.

First, how to stick the kitchen wall tiles firmly.

1. Before pasting kitchen wall tiles, the wall base should be treated. The base layer should be cleaned before tiling, such as lime paste, latex paint, wallpaper and other decorations on the wall, or there is dirt on the ground, it must be cleaned up, otherwise the cement mortar and the base layer are not firmly bonded; In addition, if there are cracks in the wall itself, it should be properly treated before tiling, so as to avoid the cracks in the basic structure from becoming larger in the future, causing the wall tiles to crack or fall off; In addition, for the ground and wall with too large a difference in flatness or verticality, cement mortar should be used for leveling.

2. Pay attention to the type of glue when pasting kitchen wall tiles. The deacetic acid type is good in transparency, fast vulcanization, and it is easy to release vinegar rot Zheng acid when curing, with a pungent odor, and it is very corrosive to coated glass, metal and some inorganic materials. The curing shrinkage rate of the dealcoholized type of wall adhesive is very small, the degree of immersion and peeling is low, and most of the raw materials are also non-corrosive, and the adhesion to marble, plastic steel and other materials is poor; When used at high temperatures, it is easy to form small bubbles, which affects the quality of tiling.

Deacidification wall adhesive should not be used in cement, stone materials, because acidic glue is easy to produce acetic acid, easy to react with the surface of cement, stone and other alkaline materials, and its expansion coefficient is very large, if the lamination is too thin, the surface will wrinkle, affecting the overall aesthetics.

Second, how long does it take to paste the kitchen wall tiles after the waterproofing project.

1. Paste kitchen wall tiles need to wait for the waterproof layer and protective layer to dry thoroughly before it can be done, and it takes about 5 to 7 days to complete the entire waterproof process, and then it can be tiled, if the construction period is not tight, it can be appropriately extended.

2. There are three main steps to make a waterproof wall with kitchen wall tiles. The first is to treat the base layer first, and the requirements are that the surface of the base layer is smooth and dry; The second is the paving of waterproof materials, which will generally be painted three times; The third is to carry out a closed water test, which is mainly to test the indoor waterproof quality.

If you want to stick the kitchen wall tiles firmly, you must do a good job of the wall base treatment before paving, and the selection of the right type of glue is also the key. After the waterproofing project is completed, the waterproof layer and protective layer need to be dried before the kitchen wall tiles can be paved.

Summary. Hello, dear, the kitchen has not been waterproofed and has been tiled how to remedy this situation can first find out the area that is prone to water leakage, such as water pipes or floor drains and other areas, if there is water leakage during use, then you can do the corresponding remedial measures according to the cause of water leakage. If the leak is caused by a pipe problem, you can find the leak first, and then replace it or repair it back.

However, if it is water seepage caused by damage to the wall, you can use a tile leak filler to protect the wall from waterproofing.

Hello, dear, the kitchen has not been waterproofed and has been tiled how to remedy this situation can first find out the area that is prone to water leakage, such as the water pipe or floor drain and other areas, if there is water leakage during use, then you can do the corresponding remedial measures according to the cause of water leakage. If the leak is caused by a pipe problem, you can find the leak first, and then replace it or repair it back. However, if it is water seepage caused by damage to the wall surface, you can use a tile leakage filler to protect the wall.

There is also the most fundamental solution is to pry the tiles, and then redo the waterproofing, although a little troublesome, but the most secure way. Remove all the bricks first, re-level the wall, do waterproofing, and then re-til. It's not very troublesome, as long as it's not a leakage of water pipes, the ground loss chain is slid and planed, the ground is cleaned and then leveled and called for branches, you can do waterproofing several times, and then do a closed water test for 24 hours, you can re-tile.