Can the rear seats of the 2018 Fengfan be modified and reclined?

Honda. The seat in the driving position is adjusted on the side of the seat cushion near the door window, and has three adjustment functions: seat position, lumbar support, and backrest. In addition, the back row of the Honda Feng Fan is not to be put down.

Honda Fengfan front seat adjustment (manual seat).

If you want to adjust the angle of the backrest, simply pull up the backrest switch and adjust it to the right angle.

Height adjustment switch: Pull up and down to adjust the height of the seat.

Forward and backward position adjustment: To adjust the front and rear position of the seat, simply pull the pull bow under the seat.

Other Honda models have front seat adjustment (power seats).

Press the lumbar support button to adjust the angle of the lumbar support;

Lift: Raise the cushion. Press down: Lower the cushion. Push forward: Move the seat forward. Pull back: Move the seat backwards;

Move the backrest switch back and forth to adjust the backrest angle.

The rear seat of the Honda Fengfan is folded down.

Remove the shoulder harness from the guide trough.

Open the trunk, find the seater release lever at the top of the trunk and pull.

Flip down the seat. <>

Honda Fengfan seat headrest adjustment.

Pull the headrest up directly with hand strength to adjust the headrest.

Press and hold the button on the side, press down the headrest to the desired position, and release the button to secure the headrest.

When the seat is reclined, the seat cover needs to be replaced. Because the two seat structures are too different. You can only check to see if the local furniture is available first. before it is possible to consider retrofitting.

Hello The rear seats do not support reclining.

To disassemble the rear seats, you need to screw out the two screws under the seat first, and then pull the buckle outward for a certain distance, and then lift the seat upward. When installing the car seat cushion, it was found that the rear seats of the car should be raised before installation, and the rear seats of the car should be lifted up before installation.

Generally speaking, the rear seats of the car are buckled between the buckle and the base, and it is not difficult to lift it, and it takes a little effort and effort to complete.

Put your hand under the cushion, and lift the front half up until the front buckle is pulled out.

After installing the rear cushion, the next step is the installation step, in fact, it is also very simple, as long as the rear half of the rear seat is stuck in, and then Huai shouted and forcefully put the front two buckles on the base of the floor to insert Minghe into it.

No other tools are needed for the whole disassembly and assembly, and attention should be paid to carefully cleaning the back cushion before and after lifting to avoid foreign objects scratching the cushion.

Millions of car purchase subsidies.

The rear seats of the new Fengfan are disassembled. The back seat of the new Feng Fan is buckled. There are two clips under the seat that need to be pinched hard. Then there are screws in the middle gap that need to be twisted open, and you can pull out the edge of the rear seat directly. The so-called seat is the seat that sits in the car.

According to the position, it can be roughly divided into: front seats: headrests, backrests, cushions, (armrests), rear seats:

headrests), backrests, cushions, fenders, (armrests). Car seats can be divided into split seats and long seats according to their shape. According to the function, it can be divided into fixed, detachable and adjustable.

According to the number of seats, it can be divided into single, double, and multi-person chairs. According to the performance of the seats, from the earliest fixed seats to multi-functional electric adjustable seats, there are air cushion seats, electric seats, three-dimensional seats, mental recovery seats, and electronic adjustment seats. According to the material, it is divided into leather seats and flannel seats.

There are also some special seats, such as child seats, racing seats. In addition, the maintenance method of leather seats, most of the high-end cars are leather seats, and many drivers install leather seats by themselves to show comfort, luxury, nobility and long service life. Naturally, maintenance should not be taken lightly.

Wipe with a cotton towel after washing. In addition to avoiding sharp objects from scratching the leather, daily maintenance should also pay attention to dust and sun protection. Because dust is pervasive, it will suck out the natural oil in the skin, and it becomes Zhang Qian's skin.

The scorching sun can make people age, and this also applies to leather seats.

The rear seat of the new Fengfan is on the buckle of the trap button, and there are two controllable clips under the seat, and after pinching it hard, then twist the screw in the gap in the middle, and finally lift the back of the seat hard, and the seat can be pulled out and disassembled. The new Fengfan is a compact sedan owned by Honda, the power is a naturally aspirated engine, matched with a 5-speed manual and CVT continuously variable transmission, the maximum horsepower is 131 horsepower, the maximum torque is 155 Nm, the maximum power is 96 kilowatts, the maximum speed is 185 kilometers per hour, the acceleration time of 100 kilometers is 10 seconds, and the fuel consumption of 100 kilometers is liters.

The length is 4450 mm, the width is 1695 mm, the height is 1477 mm, the wheelbase is 2600 mm, the front track is 1482 mm, the rear track is 1471 mm, the minimum ground clearance is 100 mm, the fuel tank volume is 50 liters, the trunk volume is 536 liters, and the weight is 1078 kg.

The drive mode is front-wheel drive, and the suspension is the front MacPherson independent plus rear torsion beam.

The tire size is 185 60R15, and the spare tire size is T135 80D15.

Millions of car purchase subsidies.

The Honda Fengfan's seat in the driving position is adjusted on the side of the seat cushion near the door window, and there are three adjustment functions: seat position, lumbar support, and backrest. In addition, the back row of the Honda Feng Fan is not to be put down.

Honda Fengfan front seat adjustment (manual seat).

1If you want to adjust the angle of the backrest, you only need to pull the backrest switch and adjust it to the appropriate angle.

2. Height adjustment switch: Pull up and down to adjust the height of the seat.

3. Forward and backward position adjustment: When you want to adjust the front and rear position of the seat, you only need to pull the pull bow under the seat.

Other Honda models have front seat adjustment (power seats).

1. Press the lumbar support button to adjust the angle of lumbar support;

2. Lift: Raise the cushion. Press down: Lower the cushion. Push forward: Move the seat forward. Pull back: Move the seat backwards;

3. Move the backrest switch back and forth to adjust the backrest angle.

The rear seat of the Honda Fengfan is folded down.

1. Remove the shoulder harness from the guide trough.

2Open the trunk, find the rear seat release lever at the top of the trunk and pull.

3. Roll down the seat.

Honda Fengfan seat headrest adjustment.

1. Pull the headrest up directly with hand strength to adjust the headrest.

2Press and hold the button on the side, press down the headrest to the desired position, and release the button to fix the headrest.