When making a color steel roof, how should I make a skeleton?

Color steel tile. The skeleton of the roof is now very popular in rural self-built houses and villas with color steel tiles to do roof decoration, although the color of color steel tiles is more, but the installation is not simple at all, if it is not installed in place, it is easy to leak, the main thing is to do a good job of the skeleton, thenWhat is the skeleton of the color steel tile roof?

1. Roofing. Start with the gable side and lay it in order from left to right (or right to left). Then, after the first plate is placed, the alignment is drawn along the lower edge of the plate.

Each piece is installed according to the alignment, and it can be checked at any time without deviation. Finally lay the surface to self-tapping the screws.

It is fixed to the strip along the center of each rib.

2. Trimming. The lap joint of the edge material of the roof (including the canopy) shall be fixed with aluminum rivets and waterproof with waterproof glue. Then the roof edge closing plate self-tapping screw head and aluminum pull nail head must be prevented by water-stopping glue.

Finally, when the construction and fixing method of the side plate needs to be changed according to its on-site measurement, the drawing shall prevail after confirmation.

3. Fixing method.

The first holder in the first row is fixed to the purlin with self-tapping screws.

On the far left, then make a reference line on the purlin elastic ink line, and then fix the same row of holders. Then the ribs of the first plate are aligned with the ribs of the fixer, and the buttons are pressed down to check whether they are fastened correctly. Then fasten the short arm of the fixing seat to the rib of the panel that has been paved, construct according to the above method, and adjust.

Lay according to the above order, and when the remaining air pavilion room is less than half of the width of the board at the end, only the plate is fixed with the short arm of the fixed seat, and the rest of the space is flooded.

Wrap up. If the last remaining space is greater than half of the width of the plate, the plate is fixed with a fixed seat, and the excess part is cut.

Advantages of color steel tile roof

1. Very durable, this ratio and concrete.

The roof construction is more convenient, and the weight is also relatively light, and it can be cut according to the angle, and the labor cost.

It is relatively low, and it can also be used again to be more environmentally friendly.

2. The service life is relatively long, this material will not be corroded and rusted under normal circumstances, and the waterproof performance is very good, more durable than other types of tiles, no need to renovate.

3. The warmth and windproof effect is good, and the material of the color steel tile is thicker than other types of tiles, so the warmth, windproof and heat insulation ability are very strong.

What should be paid attention to when installing color steel tiles

1. In the process of installation, the construction personnel must take protective measures, such as hand, helmets and safety ropes, etc., to avoid accidents.

2. The personnel of high-rise construction must be trained and hold a certificate of high-altitude work, otherwise they cannot participate in the construction operation.

3. The firmness and bearing capacity of the skeleton of the color steel tile must be very good, so as to avoid collapse or falling.

4. When moving on the spot, it is best to walk in the middle of the color steel tile, and not step on the edge of the place where the force is not strong.

All use screws to connect the light steel structure color steel room, which is equipped with common power sockets and other facilities, open line sources should not be installed or hung on the steel skeleton of the color steel room, should be designed square plastic wire pipe or trunking insulation to lay apart to prevent leakage and electric shock. The skeleton of the color steel house should be sprayed with paint once or more in 12-24 months under normal circumstances, which can prevent the steel frame from rusting and will also make the color steel house beautiful and eye-catching.

Take one side as the starting point, lay from left to right, put a whole line on the board surface, as a benchmark, and then fix it with self-tapping screws, fix it with nails at the place where the edge material is lapped, and then glue it to prevent rain, so that the skeleton of the color steel roof is done.

Some materials should be selected to make relatively good materials, mainly when making each separated place should be connected, so that the skeleton can be very perfect.

When making a color steel roof, the skeleton is based on the edge of the gable and laid from left to right. Then after the first board is placed, pull the alignment along the lower edge of the plate, install each plate according to the alignment, and check it at any time to avoid deviation. Lay the surface with self-tapping screws and fix it to the ribs along the center of each rib.

When cutting the color steel plate, its exposed surface should face downward, so as to avoid the file chips generated during cutting from sticking to the surface of the coating and vaporizing the surface dust. Color steel tile is a non-combustible material, which can meet the requirements of the fire protection code of the mobile house. It has a unique structure and good waterproof and rainproof effect.

When it is used as a roof, it is guaranteed to be watertight.

1.The color steel tile roof is in the air for a long time, which requires the coating used to paint the color steel tile to achieve a certain weather resistance. And this lacquer is not easy to crack and fade in the weather.

If you want your roof to be as eye-catching as possible, opt for brightly colored paints. This material has a long service life, usually does not corrode and rust, has very good waterproof properties, and is more durable than other types of tiles. Moreover, the color steel tile is thicker than other types of tiles, so it has strong heat preservation, windproof and heat insulation capabilities.

2.During the installation process, construction personnel must take protective measures such as hands, safety helmets and safety ropes to avoid accidents. High-rise construction personnel must be trained and hold a high-altitude work certificate, otherwise they cannot participate in construction operations.

The frame firmness and load-bearing capacity of the color steel tile must be very good to avoid collapse or falling. When moving on the spot, it is best to walk in the middle of the color steel tile, and do not step on the edge of the place where the force is not strong.

3.Temporary fixation should ensure the safety of the components and facilitate correction, including plane position, elevation, verticality, etc. When the correction is accurate and meets the requirements, it can be finally fixed according to the connection method required by the construction drawing.

When the second truss is fixed, it can be connected to the first truss by purlins. Clean it up with brushes and other tools before proceeding to the next work procedure. The surface of the steel after rust removal is qualified, and if the rust has returned before the primer is applied, the rust needs to be removed again.

The above is the answer to the question of what is the practice of the skeleton when making color steel roofs.

The production method is to splice all the skeletons and then weld them, so that all the skeletons can be built, and a very strong beam can be made.

It is necessary to take the edge of the wall as a starting point, and then lay it in turn, mainly to pull the alignment line at the lower edge, and also pay attention to inspection at any time, and avoid deviations.

Enter the area and get the decoration for free**].

Nowadays, when we walk on the road, we will see that the roofs of some houses are made of color steel tiles. The characteristics of color steel tiles are: light weight, rich color variety, rain and fire prevention, generally used to build the roof of the current warehouse.

The following is an introduction to how to make the skeleton of the color steel tile roof. 1. How to make the skeleton of the color steel tile roof 1, lay the roof first, start from one side, and then lay it from left to right or from right to left. When the first board is laid, install a alignment on the board surface, and go down vertically along the lower edge, and lay each board needs to follow this alignment to prevent the position from being deviated when the paving is burned.

2. After Zhaoye is laid, it should be fixed with screws, and it is best to use self-tapping screws. 3. At the lap joint of the edge material, it is fixed with nails first, and then glued to achieve the purpose of rainproof. It is a difficult job to make the skeleton of the roof of the color steel tile, and it is best to ask professionals to make and lay it for your personal safety.

2. What are the benefits of color steel tile roof 1. Compared with the direct wall building method, it is lightweight, whether it is installed or used, it is more convenient, and it can be cut according to its own requirements. It also has a relatively long service life, generally speaking, if it is not deliberately damaged, it can be used for more than ten years, and if it is often sprayed with some anti-corrosion materials, the service life can reach thirty or forty years. 2. It has a unique structure, waterproof and fireproof, and has the performance of warmth and heat insulation.

Use it to build a roof, which can effectively prevent rain leakage; In windy weather, it is also very windproof. 3. How to choose the roof made of color steel tiles to be in the air for a long time, which requires that the paint used to achieve a certain degree of weather resistance when painting the color steel tiles; And this kind of paint is not easy to crack and fade under the wind and sun; If you want your roof to be as eye-catching as possible, opt for brightly colored paints. Summary:

The above is the content of how to make the skeleton of the color steel tile roof and the benefits of the color steel tile roof, I hope it can help you. If you want to know more, please pay attention to Qeeka Home.

Do the math how much it will cost you to renovate your home

At present, most of the roofs of commercial houses are designed with flat roofs, that is, they are directly poured with cement to form the Sui family. For self-built houses or villas, the roof is generally the design of a sloping roof, and the roof will be installed with color steel tiles, glazed tiles, etc., the style is very beautiful, and the color is also good-looking, but it is more troublesome to make than a flat-roofed roof, and the skeleton needs to be built first, so what is the skeleton practice of the color steel tile roof? Let's take a look with Qeeka Home experts.

1. What is the skeleton practice of the color steel tile roof.

Lay the steel plate first, determine the starting point, start from the side of the gable, and lay it from left to right; After the first plate is laid, pull up the alignment along the lower edge of the steel plate to ensure that each piece of steel plate laid later is within the alignment; Then use self-tapping screws to fix the steel plate on the rear; Finally, do a good job of trimming and waterproofing.

Second, what are the advantages of using color steel tile roofing materials.

1. Good durability.

Color steel tile material is generally used more in rural self-built houses, it is also well used in temporary buildings in the construction site, compared with cast-in-place roofing, the installation is more convenient, and the quality is light, can be used, and can be cut at will according to the use of needs.

2. Long service life.

The service life of color steel tile is long, basically not affected by the external environment, and there will be no corrosion, rust and other problems, the key is to have a good waterproof effect, there will be no water leakage problem, compared to other tiles, do not need to be renovated.

3. Keep warm and windproof.

The color steel tile material is thicker than the ordinary color steel, so it has a good warmth, windproof ability, and has more advantages in heat insulation.

Summary: The above is about the skeleton of the color steel tile roof, and what are the advantages of using color steel tile roofing materials, I hope to share the content of the friend demolition can give you some reference, want to guess the cheats to learn more about related knowledge, you can **** Qijia network information.

<>1. Take the gable side as the starting point, lay it from left to right, wait for the first board to be placed, pull the alignment along the lower edge of the board, and install each piece according to the alignment, pay attention to check at any time and not deviate. 2. The laying surface is fixed on the strip with self-tapping screws along the center of each plate. 3. Use aluminum rivets to fix the lap joint of the roof edge material and use waterproof glue for waterproof operation.

4. The first fixed seat in the first row is fixed on the far left side of the purlin with self-tapping screws, and then the purlin elastic ink line is used as the reference line, and then the fixed seat is fixed in the same row, and then the short arm of the fixed seat is buckled to the first paved panel rib, and then the hole is constructed according to the previous method and adjusted. 5. Lay with the above methods, and lay until the remaining air pavilion is less than half of the plate width, and use the short arm of the fixed seat to fix the plate. 6. When cutting the color plate, the leakage surface should be facing downwards to avoid the frustration caused by cutting from adhering to the coating surface and causing gasification.

7. Do longitudinal lap joint, the overlapping length can be controlled at more than 15 cm, the water-stopping glue should be in accordance with the requirements of the design drawing, and the local potato lap position should be at the position of the extension.

The skeleton method of color steel tile roof is a relatively common residential building at present, and its structure is stable, the construction period is short, the waterproof performance is excellent, and the finger stool is widely used.

First of all, the main body of the roof skeleton of the color steel tile roof is made of steel, which has high strength and toughness, which can effectively support the tiles and other roofing materials and reduce the construction cost.

Secondly, the construction speed of the color steel tile roof skeleton method is fast, which is suitable for more urgent construction requirements. And the modern construction technology and technology make the waterproof, thermal insulation and thermal insulation performance of the house be effectively improved.

Finally, the environmental performance of the color steel tile roof skeleton method is also worthy of affirmation. It uses the best building materials, which reduces the impact on the natural environment. And in the process of use, it can effectively reduce exhaust gas emissions and protect the ecological environment.

In general, the color steel tile roof skeleton method is not only economical and practical, but also takes into account environmental protection and construction efficiency, and has been favored by many practitioners and residents in the construction industry of Weisun Tourism.