What is the way to smash a 30 30 floor tile at the bathroom floor drain?

With a chisel and a hammer, this requirement can be achieved.

I think it's okay to use a cutter.

However, if there are other pipes such as wires buried under the floor tiles, you may be afraid of cutting the pipes.

You can't use the smashing method.

If you smash it, it is not a problem of one 30x30 floor tile, but several.

Alas, it's a bit of a trick...

It is possible to cut along the edges of the floor tiles with a cutter and then carefully knock them off with an electric pickaxe. But be careful, especially with the waterproof layer underneath. Be sure to do a good job of waterproofing before installing a floor drain!

Ask the bricklayer master outside, I don't know if your bathroom tiles are wall tiles pressed floor tiles or floor tiles to wall tiles. If the wall tiles are pressed against the floor tiles, the tiles of the entire bathroom must be knocked off and repasted, and if the wall is pressed against the floor, you can replace a few tiles separately.

The cutter cuts the gap outside the four sides, so that it is separated from the four sides, and then uses a chisel to slowly repair the unwanted places.

Hello! It is recommended to use a percussion drill to knock it off, which is more accurate.

You can blow it up with a cannon.

I don't know what to do to break a floor tile in a bathroom drain, but if you give it to a professional, they can easily knock it down for you without damaging the surrounding floor.

To avoid injury. around the floor tiles. It's going to be a small station. A little bit of t down. Certainly will not be fashionable around the tiles.

This is usually done by a professional.

Replace the floor drain in the bathroom, use a screwdriver and pliers to completely remove the original floor drain, and remove the surrounding cement, sand, cement and other debris. Put the filter shaft dipped in water into the floor drain base, rotate it appropriately, fully combine the silica gel around the filter shaft with the base, install the filter screen, and complete the replacement. If it's around a corner, you can stick it with some sewing agent to avoid swelling.

If it's in **, it's really ugly, then consider replacing it with a single piece. Here's how: Use a hammer and chisel to knock off the broken tile and the original tile adhesive until the original cement wall is exposed.

Reattach the tiles with tile adhesive (mix the tile adhesive well first, then apply the tile adhesive to the back of the tile with a spatula). Paste the tiles. Once the tiles are applied, tap the tiles with the wooden handle of a hammer to make them fit evenly against the wall.

The floor tiles in the bathroom were shattered, and the cement was exposed, indicating that the tiles had fallen off. In this case, the remedy is more thorough, that is, to remove all the original tiles, remove the cement mortar used to lay the tiles, and then re-lay the tiles.

Then, replace the tiles on the damaged parts, so that there will be different colors and color differences of the tiles, and the visual effect will definitely not be so good. After the tiles are applied, it takes 8 hours to caulk. When caulking, use a soft rubber scraper to fill the gaps around the tiles in the direction of the tiles.

What's more troublesome is that there are too many ceramic tile styles on the market, and they are updated quickly, especially some special styles; Many styles may not be produced after entering the market for a period of time. As a result, the tiles that were renovated a few years ago were damaged, and it would be difficult to find the same style to repair if they were not repaired when they were renovated.

Before replacement, the specifications of the floor drain should be selected to ensure smooth installation. At present, the more common ones are 10*10cm square floor drain and 12cm round floor drain. This floor drain can be sized according to actual needs.

Use a screwdriver or other tool to separate the broken and old floor drain from the floor tiles, and then use a straight screw to remove the surrounding cement. If the old floor drain is tiled, you can use a hammer to separate the cement from it, and then use a groove to clean the surrounding cement. Break the broken floor tiles and use a steel drill to scrape the dust underneath.

Remember, be lower than other floor tiles. Then soak the cement thoroughly, wipe the floor tiles to be replaced, put them in the shovel place, and gently compact. Remember, the plastering should be evenly spread, without unevenness or gravel.

You can ask the workers for compensation, or you can ask the workers to repair their floor tiles, as long as the floor tiles can be used normally, and there is no need to make things difficult for the workers.

Workers must be compensated, and since you do this industry, you should have a certain amount of technology and ability. The damage definitely needs to be compensated.

The worker should be given some compensation, because it was caused by the worker's mistakes, and he should be compensated.

Floor tile leakage is a headache. Traditionally, it is necessary to smash the floor tiles, then re-repair the waterproofing layer, and finally apply the tiles. If you smash bricks, it will be laborious and costly.

However, with the development of science and technology, it is now possible to fill the leakage under the floor tiles in the bathroom without smashing the floor tiles.

The use is Shuanghong waterproof waterproof waterproof repair glue that does not smash bricks.

Non-smashing brick plugging agents include permeable A and crystalline B components as well as curing agents. It uses water as the carrier to quickly penetrate into the substrate, and the expansion and curing reaction occurs at regular intervals to form an impermeable transparent colloid that is resistant to acid and alkali, corrosion and high flexibility, so as to completely block the capillary pores and gaps of the cement structure and obstruct the passage of water molecules to achieve permanent waterproofing.

Advantages: 1. Colorless, odorless, transparent and environmentally friendly;

2. The construction is simple, no bricks, no grouting, no change in appearance and facilities.

Scope of application: Mainly for kitchens, bathrooms, balconies, pools, etc. that leak after paving the floor tiles.

Summary. Pro, the grouting method can also be used without smashing bricks for waterproof plugging, that is, when carrying out the construction of waterproof and plugging bricks in the bathroom, relying on the natural infiltration of waterproofing agent, the reaction under the tile generates water-insoluble colloids and crystals, blocking the capillary pores and capillary leakage water channels, and playing the role of waterproof plugging. 2. The premise of construction is that the moisture under the tile is not sufficient, but the water consumption is large on some occasions, and the reality does not allow enough time to ensure the evaporation of the water under the tile, and the grouting is carried out in an inconspicuous position in the bathroom, and the water under the tile is squeezed out by grouting method, and the waterproofing agent reacts in the leakage channel under the tile to generate insoluble colloids and crystals, which plays a thorough waterproof plugging role.

The use of low-viscosity two-liquid grouting machine for waterproof and leakage plugging construction without smashing bricks greatly improves the construction efficiency.

Pro, do not smash the bricks waterproof this closed plugging can also use the grouting method, that is, in the bathroom without smashing the bricks waterproof plugging construction, relying on the natural infiltration of the waterproofing agent, under the tile reaction to generate insoluble colloids and crystals, blocking the capillary pores, capillary leakage water channel, playing the role of waterproof plugging. 2. The premise of construction is that the water under the tile is not sufficient, but the water consumption is large on some occasions, and the reality does not allow enough time to ensure the evaporation of water under the tile. The use of low-viscosity two-liquid grouting machine for waterproof and leakage plugging construction without smashing bricks greatly improves the construction efficiency.