What is the difference between full tile and half tile ceramic tile?

Full tile and half tile are rare in modern times, the difference between these two types of tiles is the difference in water absorption, the water absorption rate of full tile is insufficient, also known as vitrified brick, the water absorption rate of half tile exceeds.

All tiles have a very low water absorption, so they cannot be soaked in water before being laid. Semi-tiles must be soaked in water before construction. In addition, the cutting surfaces between them are also different, and ** are also different.

Characteristics, generally the whole tile hardness is higher, not easy to crack, dirt resistance, high water absorption, good flatness. Semi-ceramic tiles have low hardness, are easy to crack, easy to penetrate, and have poor gloss.

1) Water absorption.

The main difference between the whole tile and the ceramic tile is the water absorption rate, the whole tile has a strict water absorption standard, only the lower water absorption rate of the tile is called the whole tile, and the general ceramic tile water absorption rate is greater than. The water absorption rate is generally less than that of ceramic tiles, more than 10% of which is clay bricks, and between the two is semi-porcelain.

Usually all kinds of polished tiles, unglazed mosaic tiles, and most of the sanitary ware are porcelain, and the water absorption rate is average; Antique bricks, small floor tiles (climbing walls), crystal bricks, wear-resistant bricks, matte bricks, etc. are stoneware bricks, that is, semi-ceramic tiles, water absorption porcelain tiles, pottery pipes, facing tiles, glazed products, etc. are generally ceramic, and the water absorption rate is 10%.

2) Adhesion.

The low water absorption rate of the whole tile makes the adhesion between the tile and the wall cement mortar small, and the wall is not very good bonding, easy to fall off, generally used as floor tiles, and ceramic tiles can be used as wall tiles, but also as floor tiles.

3) Hardness. The hardness of the whole tile is higher than that of the ceramic tile, and the production process of the whole tile should be more refined, and the corresponding full tile should be a little more expensive.

1) Cleanability.

The hardness of the whole tile is very high, it is not easy to break under normal circumstances, and the surface of this tile has not been polished, so there is no polishing pores, it is very easy to clean, and the anti-fouling ability is good; The appearance of the whole tile has good flatness, the water absorption rate is very low, and it can be directly paved on the wall without soaking in water during installation.

The appearance of ceramic tiles is smooth and delicate, the surface is crystal shiny, the colors are diverse, the patterns are numerous, and they can be matched with different home styles to meet the needs of different consumers.

5) The composition is different.

Full ceramic tile is also known as vitrified brick, the main material is clay, quartz sand, etc., through grinding, mixing, pressing, sintering and other processes to make acid and alkaline resistant building decoration materials. The industry mainly defines the whole tile according to the water absorption rate, and the tile that has been burned through and the water absorption rate is less than that is called the whole tile.

Ceramic bricks are mainly made of clay and other non-metallic materials, through molding, sintering and other processes to produce block ceramic products, usually at room temperature by dry pressing, extrusion or other methods of molding, sintered at a certain temperature, mainly used to decorate and protect the walls and floors of buildings.

In people's daily life, ceramic tiles are very common, now there are many types of ceramic tiles on the market, today I want to share with you what is the difference between full tiles and half tiles, friends who want to know may wish to take a look at it!

1. What is the difference between full tile and half tile.

The water absorption rate of full ceramic tile and half tile is different, the water absorption rate of full ceramic tile is relatively low, so there is no need to soak in water before paving, and the water absorption rate of half ceramic tile is higher, so it must be soaked in water before paving. The hardness of the whole tile is high, and it is not easy to break, and has a certain anti-fouling ability; Semi-tiles have a low hardness, are prone to chipping, and have poor gloss.

Second, how to distinguish between full ceramic tile and half ceramic tile.

1. Distinguish from the water absorption.

If you pour water on the back of the tile, the tile that absorbs immediately will be half tile, and the tile that does not absorb much water will be a full tile.

2. Distinguish from the name.

Full tile is also known as: polished tile and vitrified brick, in addition to cloud shadow stone, amber jade, etc., these are called or refer to the whole tile. Its main use is for indoor floor paving, while semi-ceramic tiles are used for decorative use of wall paving.

3. Distinguish by tapping and listening to sounds.

Gently tap the middle of the tile with your hand and listen to the sound it makes, if the tile is relatively thick and accompanied by a long echo, then this kind of tile is a full tile. If the sound echo of the tile is small, and the sound is short, muddy and has no echo, it means that this type of tile is a semi-tile. Because the porcelain degree of the whole tile is relatively poor, and the size of the raw material particles of the inner embryo body is uneven, the density of the tile is small, and the sound emitted by the letter group is not long enough and has an echo.

Summary: The above is for everyone to share what is the difference between the all-ceramic sliding tease brick and the half-tile and how to distinguish between the full tile and the half-tile, I believe you have a corresponding understanding after reading the above sharing, I hope the above sharing can help you, if you need to know more about it, please continue to pay attention to Qeeka Home**.

1. In front of the current decoration market, few people will say full tiles and half tiles. There is still a certain difference between the two, and the main manifestation is the difference in water absorption. Choose a full tile, its water absorption rate is generally within the limit, and the water absorption rate of half tile is exceeded.

2. The hardness of the two is also different, the hardness of the whole tile is slightly higher, so it is not easy to produce the problem of breaking, and its anti-fouling ability is slightly stronger, and the flatness is better. However, the hardness of semi-tiles is relatively low, and at the same time, it is easy to break, and it is easy to penetrate, and the gloss is not particularly strong.

3. When you use it, you will find that the water absorption rate of the whole tile is slightly lower, so you don't need to soak in water when paving. However, when choosing a semi-ceramic tile, you need to go through the process of soaking in water before construction, otherwise it will affect the adhesion of the tile.

There are three differences: different water absorption, different precautions for use, and different colors.

1. The difference in water absorption

The difference between full tile and half tile is mainly different water absorption, generally speaking, full tile refers to the tile with water absorption less than 0 5, also called vitrified tile; Half tiles are tiles with a water absorption greater than 0 5.

2. Different precautions for use

Generally speaking, it is recommended to use all-porcelain on the ground, which is because of the low water absorption rate and stable quality of all-porcelain, which is convenient to take care of the wall in the later stage, and you can use half ceramic tiles (especially kitchen walls), mainly for the following reasons:

1) Because the hardness of the whole tile is too high and too brittle, it is troublesome to install things in the later stage, and many masters like to use impact drills, which is easy to collapse or even knock off the tiles.

2) The water absorption rate of the whole tile is low, and some even do not absorb water, so the adhesion with the cement is relatively poor, and the possibility of falling off after a long time is attached to the wall.

3. Different colors

If you pour water on the back of the tile, you will be able to suck it in quickly, and if you pour it in, it will be a half tile, and vice versa. It can also be distinguished from the use: antique tiles, polished tiles, vitrified tiles, matte tiles, etc. on the general market are all ceramic tiles.

Of course, it will be better to choose full tiles when decorating, but some full tiles with poor quality, although they are called full tiles, the quality is not as good as half tiles.

The difference between full ceramic tile and half ceramic tile: different appearance, different hardness, different water absorption, different construction requirements.

1. The appearance is different

The gloss of the former will be worse than that of the latter, and the flatness is also better than the former, if the user wants a good decorative effect, he should choose to buy the latter.

2. The hardness is different

The hardness of the former is worse and it is easy to detect fragmentation, while the hardness of the latter will be higher, more resistant to hitting, and it is not easy to chip.

3. The water absorption rate is different

The water absorption rate of the former is higher, generally between 10%, while the water absorption rate of the latter is relatively low, generally not exceeded.

4. The construction requirements are different

The former must be soaked in clean water in advance before laying, while the latter can generally be directly used for tile paving construction without soaking in water in advance.

Precautions for buying tiles:

1. Flatness: Two tiles are paired together, we can observe the gap between the two tiles, the smaller the gap between the tiles, the better the quality.

2. The stain resistance is written with an oil-based pen, and if the oil stains can be wiped clean after drying, it means that the stain resistance of the tile is better.

3. Slip resistance, we can go up and walk around, observe whether there is a feeling of friction, if there is a feeling of friction, it means that the tile has good slip resistance.

4. The whole tile with good water absorption is usually almost not absorbent, and we can carry out a drip test to observe whether the tile absorbs water.

5. The wall tiles are paved with semi-porcelain wall tiles, and the water absorption rate needs to reach 10% in order to play a firm role.

6. Guangdong brick identification We can use the help of tapping tiles to distinguish the sound to judge, usually the sound will show a crisp metallic texture feeling.

7. The size of the floor tiles can be selected according to the size of the room.

8. Tile color differenceWhen we buy tiles, because the lights of the merchants are designed, they look shiny, and this will definitely have color difference, so we must be psychologically prepared.

9. Ask clearly about the items included in the project, and ask clearly whether the ** of the tile includes the delivery fee, so as to avoid unnecessary disputes in the later stage.

10. Tile acceptance tile sent upstairs, we first check whether there is a problem with the quality of the tile, and then carry out the follow-up signature work.

The difference lies in the water absorption, and the full tile refers to the tile with less water absorption, also known as vitrified brick. The water absorption of half tiles is greater than

1. All-porcelain tiles have high hardness, are not easy to break, have high anti-fouling performance, low water absorption and good flatness.

Semi-porcelain tiles have low hardness, easy to break, easy to penetrate, and poor gloss.

2. The water absorption rate of all-porcelain is very low, and it can be paved without soaking in water, but the semi-porcelain also has to be soaked in water for construction, as if the red brick does not have the feeling of burning through, and the cut surface of the brick is not the same, and it is not the same.

3. All ceramic tiles are vitrified tiles, all porcelain, non-absorbent, strong anti-fouling ability, specification *600.

All-porcelain ceramic tiles have high hardness, not easy to break, high anti-fouling performance, low water absorption and good flatness. Semi-porcelain tiles have low hardness, easy to break, easy to penetrate, and poor gloss.

How to distinguish between full and half tiles

1. Pour water on the back of the brick with a small amount of water, pour water on the tile in reverse, and the semi-porcelain will be absorbed immediately, and the all-porcelain will not absorb much.

2. It can also be distinguished from the name and use, and the general full ceramic tile is called polished brick, vitrified tile and so on.

There is also a general call with a certain stone, a certain jade, such as cloud shadow stone, amber jade, etc. are all tiles, the use of most of the household sticky floor is all porcelain, household sticky wall is all semi-porcelain.