-
Pry the original one, take it to the decoration market to buy a floor tile of the same type, use a cutting machine to cut along the four sides of the bad floor tile to leave a centimeter of place, knock off the middle part, and then gently take off the remaining four sides, be careful not to damage the adjacent floor tiles, clean up the original mortar, wet with water, not on 1:4 cement mortar, soak the floor tiles in the water, and wait for the water to dry on the reverse side of the cement slurry, paste it and knock it flat to block it within a day and don't let people step on it.
-
If it is a renovated house. In the case of broken floor tiles, the bricks that need to be broken need to be removed and replaced with a new brick.
1. In the case of the same batch of bricks, there should be no color difference, and if the bricks are supplemented in addition, there will be color difference.
2. If it is rotten during the decoration process, it will be much easier to repair.
-
For a new one, epoxy adhesive can be used.
-
The surface of the solid wood floor is easy to be scratched, especially if some heavy objects or sharp objects fall on the wooden floor, the floor will be scratched, and there will be many fine cracks when the fine sand particles walk on the floor. To prevent scratching the floor, it is recommended that you place a rug at the door to prevent sand from being brought inside. The remediation of solid wood flooring depends on the degree of scratches, if the surface paint film is scratched, it can be treated with polishing and waxing, and it can be wiped clean.
In addition, if the scar is deep, it is filled with solid repair wax, then painted with a touch-up pen, and finally polished. If you find it cumbersome, you can buy a bottle of floor wax and wipe it like a normal mop, and some scratches that are not particularly deep can be dealt with.
-
You can clean out this broken brick, clean the floor mortar, and then pave the floor tiles of the same color and type prepared in advance. The joints of the newly pasted floor tiles should be filled with white cement slurry, and a layer of waterproofing agent should be applied after drying, so as to prevent the brick joints from getting damp, turning black and smelly.
When paving floor tiles, professional decoration workers should be preferred, if in order to save money personal paving, you should fully understand the floor tiles before paving, paving, after the need to pay attention to matters, do not misoperate, otherwise it is likely to have problems.
-
The first is to find a decoration master, buy some materials to open the broken floor tiles, and then re-pave a piece.
The second kind of self-paved is described in detail below:
1. Remove caulking white cement along the edges of the tiles and carefully remove the damaged tiles with a small chisel. If the surrounding tiles are firmly pasted and you don't want to replace all the surrounding tiles, you can use a glass cutter to carve the middle of the tile, chisel the middle part of the tile first, and then use a sharper steel chisel to slowly repair the broken porcelain blocks around the edge.
2. After the tile is chiseled, the bottom cement mortar is chiseled off with a steel chisel, and the force should not be too heavy, otherwise it will shatter other intact tiles. After removing the dust, the surface should be moistened with water.
3. Before pasting tiles, the tiles should be soaked in water and moistened, and after drying, a layer of 107 glue cement slurry should be scraped on the back of the tiles, and then pressurized in place, and check whether the newly pasted tiles are flush with the surrounding tiles.
Fourth, the joints of the newly pasted tiles should still be filled with white cement slurry, and the excess cement slurry on the tile surface should be removed.
5. Sometimes the old tile is still intact, but it is disconnected from the junction with other finishes, and the sand and ash at the joint should be removed when repairing, and epoxy resin adhesive should be injected, and then the joint should be repaired with waterproof flexible caulking material (such as glass glue) after drying.
Six Sometimes old tiles are broken only.
One or two pieces, and the original cement mortar is difficult to chisel off or chisel hair. At this time, you have to use epoxy resin glue (all-purpose glue) to apply a thin layer on the back of the tile and the cement wall, and then press hard to ensure that the new tile is flush with the surrounding tiles.
-
1. If you find that the tile is only a hollow drum in the corner, you can use the hollow part of the drum to water, that is, to smash the gap first, and then pour the good cement into the gap. In this way, Xiaochong can avoid the overall replacement and save expenses.
2. Local hollowing, if the tile is partially hollow, if it does not affect the daily life and aesthetics, it can actually be dealt with; But if there is an impact, it is necessary to knock off some tiles and re-pavement.
3. Crack repair, because the silver has been used for a long time or has been hit by various falling hard objects, it is possible to cause various cracks on the surface of the tile. If it doesn't affect the overall aesthetics, you can do a simple treatment. If it is a more obvious crack, it is recommended to replace it.
4. The mortar is not loose, if only the tile has fallen off, but the mortar is not loose, you can clean the mortar on the back of the tile and the surrounding adhesion, and then mix it with 107 glue and a little cement, apply it evenly on the back of the tile, and then gently press it to stick the tile firmly.
5. The mortar has peeled off, if the mortar has also begun to fall off, it is necessary to dig out the pit on the basis of the front, and then repeat the practice of the fourth point. It should be noted that you should not hit it too hard.
6. If the tile itself is very intact, but the finish junction is disconnected, at this time, you can first clean all kinds of dirt at the joint, and then inject epoxy resin adhesive, and after it is thoroughly dried, use waterproof flexible caulking material at the joint.
-
1. Use epoxy resin glue to repair the floor tiles: first clean the surface of the floor tiles, then open the resin glue, mix A glue with B glue and stir, note that A:B is 2:
1。After that, apply it to the bad part in time to avoid the glue drying out and not being usable. Usually at room temperature, the curing time is 2-6 hours.
Do not step on the floor tiles for 24 hours. In general, the glue after 10 has the best effect. If the weather is bad, try to keep the room temperature in the range of 15-25 degrees, at which the glue bonding effect is better.
2. If the edge of the floor tile is bulging, you can chisel a small hole from the appropriate gap position, and then mix cement mortar, and then pour it into the gap to repair. 3. If it falls off directly, you need to remove the floor tiles that have fallen off, then mix a little cement mortar and add 107 glue to re-apply it to the floor tiles, and then put it back in its original position and press it to stick firmly. Understand the TV network
-
Dear, remove the old tiles. To remove, apply a piece of masking tape to the center of the tile. Then, put on your goggles and drill a hole with an electric drill and carbide drill bit where the tape is attached.
Remove the tape and use a glass knife to make an "X" on the tile. Then, use a chisel and hammer to break the tiles and remove the debris. Use a putty knife or a grooved paint stick to apply the ceramic sand glue to the back of the new tile, keeping the tile edges clean.
Carefully place the new tiles into the notch of the wall. Compact the tiles and gently move them up and down, left and right, so that the sand glue is evenly distributed. The gap around the first tile should be even, and it should be accurately aligned with the surrounding tiles.
Glue the tiles firmly with masking tape or plain tape and allow the sanding glue to cure according to the manufacturer's instructions.
-
1. In the case of a small piece of rotten, you can use the floor adhesive tape to roll the glue, this method is only suitable for small area damage. 2. If the rotten position or condition of the floor tile can not be glued, you can buy a piece of the same floor tile, and then cut and polish it according to the size of the rotten position, and then use the floor adhesive to stick it to the bad position. If you can't find the same tile, try to use one of a similar color.
3. You can also take off the broken floor tiles, then cut and polish them according to the size of the rotten position, and then stick them to the bad position with floor adhesive. If you can't find the same tile, try to use one of a similar color. 3. You can also take off the broken floor tiles, and then take the same floor tile and operate according to the standard of laying floor tiles, first clean and level the bottom, and then mix cement mortar and add 107 glue to the back of the new floor tile, and then put the floor tile back to its original position and press it firmly.
Understand the TV network
-
<>1. In the case of a small piece of rotten, it can be glued with floor adhesive, which is only suitable for small area damage. 2. If the rotten position or condition of the floor tile can not be glued, you can buy the same floor tile, and then cut and polish it according to the size of the rotten position, and then use the floor adhesive to stick it to the bad position. If you can't find the same tile, try to use one of a similar color.
3. You can also remove the broken floor tiles, and then take a piece of the same floor tile according to the standard operation of laying floor tiles, first clean and smooth the bottom, and then mix cement mortar and add 107 glue to apply it on the back of the new floor tile, and then put the floor tile back to its original position and press it firmly.
-
What to do with your rotten floor, I because if the floor is rotten, we can smash the floor to the ground, or re-apply a good wooden board to grease it and brush it all over again, so that the floor will not become one.
-
If the damaged area of the floor is not very large, you can use the way of grinding and painting to solve, wipe it with a dry rag after polishing, if the floor is damaged in a large area, the part of the local damage needs to be re-paved, the process is more complicated, it is recommended to ask professional renovation workers to come to deal with it.
-
The brick surface is partially uneven, hollow, cracked, etc., and generally needs to be replaced. There are two ways to replace it: one is to carefully knock the tile to be replaced (note that the force should not be too large), and then pry the brick around, remove the brick that needs to be replaced, and repair it again.
If the brick is not pasted for a long time, the cement on the wall is not completely dry, you can carefully pry the cement off, paste it with cement slurry, if it is used for a long time, the cement is completely solidified, you can use special tile adhesive paste (tile adhesive is available in the major building materials market).
Another way is to use a marble machine (a tool specially used to cut tiles) along the diagonal line of the tile, be careful not to scratch the four corners of the tile, from the corner of ten centimeters, and then use a hammer to break the diagonal intersection point (in the middle of the tile), with a chisel from the middle to the surrounding pry, so that the surrounding tiles will not be damaged. After taking out the bricks, you can re-paste them.
Tips: The replacement of tiles needs to pay attention to their color number is consistent, otherwise there will be color difference, so it is recommended to leave a small amount of tiles when tiling for future repair. If you don't keep it, it's best to take the pry off tile fragments to the point of sale as they are**.
For the scratches on the tiles, the glazed tiles can be sanded with fine sandpaper and carefully sanded on the brick surface, which can get some effects. Be sure to do it with water. This method can get a good effect on small scratches on the brick surface.
Vitrified tiles can also be carried out using the above-mentioned glazed tile method. The force should not be too strong; You can also use a polishing machine to add water to polish to keep the strength even, which requires professional operation.
-
The floor is rotten a lot, what to do with the rotten floor? It may be that the floor is rotten due to the wet floor, and the cause should be found and the rotten floor should be replaced.
-
If most of the floors are rotten, you can only replace them and buy a new batch to put them on.
-
The floor is so good, how to deal with it, then you just have to warp the floor all over again, and the floor can be better.
-
If the floor is rotten, it is better to re-specialize if there are conditions.
Use a mop and add some oleace to mop. 1. Keep the floor dry and clean, and it is not allowed to wet the mop with water or scrub with alkaline water and soapy water, so as not to damage the brightness of the paint and damage the paint film. If it is dusty or dirty, wipe it with a dry mop or a wrung out wet mop. >>>More
Avoid the color difference of the floor tiles:
1. We must carefully check the batch number and color number when accepting the ceramic tiles. If you find a product with different batches and color numbers, you should notify the seller in time or refuse to accept the batch of goods. >>>More
In home decoration design, most families attach great importance to the decoration design of the ground, and many families choose floor tiles for decoration in the selection of ground decoration materials. Floor tiles are very common and are the most classic floor decoration materials. In daily life, we will inevitably drop stains on the floor tiles, and we will have questions about how to remove the stains on the floor tiles. >>>More
The varieties of floor tiles include full-body bricks, glazed tiles, full-body polished tiles, infiltrated tiles, infiltrated polished tiles, etc. When it comes to the color matching of floor tiles, it is still determined according to the decoration style of the home. There are also house types to design. >>>More
Common stain removal methods for floor tiles:
1. Daily cleaning of ceramic tiles can be cleaned with dish soap, soap, etc. >>>More