What are the best ways to punch holes in glass?

Updated on healthy 2024-07-13
19 answers
  1. Anonymous users2024-02-12

    Introduction: Glass is becoming more and more important in life, because glass is used in many daily life, such as glass sliding doors, glass cabinets, glass windows. Many times when installing these products, it is necessary to punch holes in the glass.

    And there are a lot of holes in the glass. So what are the best ways to punch holes in glass? <>

    First of all, the reason for punching holes is that it can be installed better, for example, like a glass doorSliding doorsBe sure to punch holes, because there are some on itScrewsIt is fixed to prevent the glass from falling and causing danger. Glass is not better than metal or the like, because it is weighty, so it must be fixed on the glass to prevent the danger of falling off, glass is a fragile item, so everyone also pays special attention. <>

    First of all, it is necessary to mark the hole with a fixed thickness according to the indication on the hole, and then determine whether the glass can be punched according to the requirements of size processing, and the edging and chamfering need to be done after the treatment.

    Perform a punch. Then according to the requirements, then use a glass drill to install the things to. First of all, when installing, you should draw the correct position, and then remove the water on the cloth, then cut it with a glass knife and knock it through, and then cut it with a glass cutting saw, and then cut it diagonally, not directly.

    To punch the hole first, place the glass bottle on the punching platform. It is best to use a carbon pen to mark the exact location of the hole, because the glass must be accurate enough to be correct, and the hole should be drilled after the mark is made to make sure that there are no errors. Add a certain amount of water to the circle next to it, the purpose of adding water is to make the glass burst when drilling.

    And when punching, we must grasp the strength, the smaller the force of ultra-thin glass, the greater the force of thick glass, so punching is a very technical content, we must pay attention to relevant matters to prevent danger when punching.

  2. Anonymous users2024-02-11

    First of all, we need to buy a professional drill bit, and then install the purchased special drill bit on the hand drill, draw marks on the position of the glass that needs to be punched, hold the drill, turn on the switch, and make the drill bit at a 45-degree angle to the glass plane.

  3. Anonymous users2024-02-10

    It can be drilled with an electric drill, or it can be punched with a grinder, and it can also be punched with a will, and it can be punched with a professional instrument, and it can also be punched with a grinder.

  4. Anonymous users2024-02-09

    You can use a drill bit to punch holes, or use a hand crank way to punch holes, or you can fix the drill bit, or you can slowly rotate the drill bit, you can mark it with a marker line, and then drill the hole.

  5. Anonymous users2024-02-08

    In our life, many people will use glass when decorating, so in the process of installing glass, there will also be a need to punch holes, which is a certain method and skill, and then I will introduce it to you.

    First of all, we must know that the thickness of the glass is still relatively large, so when punching holes in the glass, we must use a special machine, so as to ensure a reasonable passage through the glass, so as not to damage other parts of the glass. In addition, in the process of perforating the glass, we must choose according to the quality of the glass, if the quality of the glass is fragile, it is not recommended to perforate, because it is likely to cause the glass to break. The second is that we must pay attention to the position of the hole when punching, we use a marker pen to mark in advance, so that it can also be carried out according to this mark when punching, and also according to the indication of the hole to the fixed thickness of the hole, and then according to the requirements of the size of the processing to punch, after the hole must be processed, but also the glass hole needs to be edging and chamfering, otherwise it is likely to cause the glass chips on the glass to enter our **, Thus causing some damage to our body.

    It can be seen that it is still a difficult task to punch holes in the glass, because many young friends will choose glass doors when decorating the bathroom, and at this time they need to punch holes in the glass, so as to install the upper row of curtains, so that the glass door can be used well.

    Finally, I want to say that if you want to buy some glass doors or other glass supplies, try to choose a better material at this time, because there are many glass materials that are not the same, if you buy cheap glass, then it is very likely that we will not be able to withstand the high temperature when taking a bath, so that there will be an explosion, which is quite harmful to our body.

  6. Anonymous users2024-02-07

    There are many products around me that are made of glass, and the glass will be made into different shapes, and some need to be punched on it, what is the specific punching method?

    1. How to operate the perforation on the glass.

    1. If you want to punch holes in the glass, you need to use a glass drill bit and prepare the tools for punching. Then in the process of punching, while watering and drilling, but not too much water, as long as there is smoke to be able to water, and then continue to punch.

    2. You can choose a hand drill, first to determine the location of the hole, the choice of drill bit is also more particular, generally speaking, the choice is a hollow drill bit, so that the ability to drill will be stronger. Place a mat at the identified location, drill a mark with a hand drill, and then take the mat. Drill a small hole in such a position, water it as you go, and then polish the hole until it meets your requirements.

    3. It can also be operated by a punching machine, and drilled by professional masters. Coupled with water cooling, it is easy to break, and the requirements for punching are relatively high. Through the punching machine to punch holes, its hole size can be effectively controlled, and the accuracy is relatively high, and there will be no wear.

    2. What are the types of glass?

    1. Flat glass, that is, the most common type of glass. It is mainly used in doors and windows, playing the role of light transmission, heat preservation and wind blocking, generally speaking, colorless, good transparency, and large and small thickness.

    2. Patterned glass, also known as patterned glass, is generally used in the design of doors and windows, such as the toilet door of the bathroom.

    3. Insulating glass.

    It is more common, it is composed of two or more layers of glass, sealed with a sealing strip around the perimeter, filled with dry gas, which can play a sound insulation effect.

  7. Anonymous users2024-02-06

    Laser perforation of glass produces glass holes with well-defined geometries. Drilling glass holes with well-defined geometries is becoming increasingly important in a wide range of industries. Glass laser drilling machines are replacing traditional drilling processes to support many applications.

    Depending on the application, a variety of lasers can be used for laser precision drilling or laser cutting of round holes. In 2016, Kolode Laser Jixiangyun Technology Co., Ltd. successfully developed a high-speed connection laser perforation equipment, and at present, the field of photovoltaic glass laser perforation has covered about 70% of the market share, and the sales volume will be 100 million yuan in 2021. Kolode laser machines contribute to the productivity of the glass industry.

  8. Anonymous users2024-02-05

    It is more convenient to choose to tape all around the perimeter of the glass and then use something more advantageous to knock the fight, and it will also avoid changes in the surrounding glass.

  9. Anonymous users2024-02-04

    You can use a special electric drill to punch holes in the glass, or you can use a glass knife that specializes in cutting glass, and the efficiency is relatively high.

  10. Anonymous users2024-02-03

    Holes can be drilled using specialized equipment, either by marking the location of the hole in advance, by using an electric drill, or by knowing the status of the hole.

  11. Anonymous users2024-02-02

    For many people, when decorating their homes, they can want to punch holes in their own glass to install things, which is very common in our ordinary life. Not only that, for punching, if we don't pay attention to it, it is easy to cause some substantial damage on the glass, which will affect the beauty of our furniture. Many people will ask the decoration master whether their furniture can be punched before punching, in fact, for the decoration master they have certain skills in punching holes in the glass, today I will teach you how to avoid damaging the glass when punching.

    Method 1: First of all, we need toothpaste and a melted container, and we also need to choose some small amount of cement, and we need to prepare these tools and then punch the holes. This simple method is that we don't need to use a drill or any other machine, we just need to lay our glass flat and then pad something underneath. Then we mix it with cement and water and put it where we want to drill the hole, and after making the middle into a funnel shape, we have to measure that the hole we make is equal to the bottom of our funnel hole.

    At this time, you pour our molten metal solution into our finished hole, and then it will melt into the hole we want along the shape of the hole.

    Method 2 The second method is also relatively simple, we only need to make our drill bit into a round sleeve according to the size of our drilling, but in the process of doing it, we need to leave a little seam, so that the drill bit can be directly punched on our manual drill. Because for the drill bit, the damage to the glass is very large, if we directly use the drill bit to punch holes, it is easy to cause our glass to be damaged. If a drill bit cover is attached to the front of the drill bit, friction can be reduced, and holes can be drilled to prevent glass breakage.

    Note: We need to check our equipment in the process of punching, if we are sure that our glass can drill gray and white foam, it means that we can start drilling, at this time we can drill through the thicker glass several times. When we are drilling, if the round knot pen and drill bit on the hand drill move, we need to repair it in time.

  12. Anonymous users2024-02-01

    First of all, you should use some particularly fast machines, and secondly, you must pay more attention when punching, you must be fast and accurate, and the orientation must be correct, as long as this will not destroy the glass.

  13. Anonymous users2024-01-31

    We need to choose relevant tools when drilling glass, for example, we can use glass drills, glass knives and other related tools to punch holes. In the process of punching, the speed should be slow, the force should be light, especially when the glass is about to be drilled, the force should be weakened. In general, the thinner the glass, the lighter the drilling force, and if the glass is drilled through quickly, it is easy to have the problem of drilling and exploding.

  14. Anonymous users2024-01-30

    I think that at this time, we should go to a professional person to punch holes, because this operation is particularly difficult, and ordinary people can't operate it. Broken glass.

  15. Anonymous users2024-01-29

    Only choose a professional grinder for punching, so that it can be effectively avoided, and you must pay attention to the strength, which is very important.

  16. Anonymous users2024-01-28

    1. First of all, we have to buy a professional drill bit, and then install the purchased special drill bit on the hand drill;

    2. Draw marks on the position that needs to be punched on the glass, hold the electric drill, turn on the switch, and make the drill bit and the glass plane at an angle of 45 degrees;

    3. Slowly approach the marking line, advance little by little, pause when a small nest is drawn, and then drip water at the marking place to lubricate and cool, and then follow the operation of the previous step to make the drill bit contact the glass.

    4. As the drill bit rotates, the hand drill slowly stands upright, so that the drill bit is finally perpendicular to the glass plane, that is, grinding out a circle;

    5. Continue to process, and slow down the advancing speed when approaching the drilling through the glass, so as to ensure that there will be no large gaps on the reverse side of the glass.

  17. Anonymous users2024-01-27

    How do you punch holes in glass? The guy taught you a very practical method, netizen: It's so simple, I will too.

  18. Anonymous users2024-01-26

    Don't go to the work yourself, you can generally punch holes in glass shops nowadays, and the price is not high.

    If you must try, you can find a straight copper pipe (according to the size of the hole you need), clamp it on the pistol drill, add a little and water-moistened emery to the glass that needs to be punched (if it is not easy to find, the coarser river sand can also be replaced), and then slowly drill on the glass, remember, you must not be impatient, and not too hard, the violent friction will make the glass burst, add water and sand while drilling, remember to be slow, especially at the moment of piercing, the action must be light, Otherwise, the consequences will be serious.

  19. Anonymous users2024-01-25

    Tool Preparation:

    1. Console, marker.

    2. Glass drill (drill bit), the size depends on how big the hole you want to open (too large a hole, can not be drilled directly.) )

    3. Pistol electric drill (others such as bench drills can also be used).

    4. Tap water.

    Processing: 1. Lay the glass flat onto the operating platform.

    2. Mark the place where the hole needs to be opened with a marker.

    3. Install the glass drill on the electric drill.

    4. Start drilling, pay attention to the beginning, drill one side of the hole first, that is, the electric drill can not be straight to the operating table, it should be obliquely fed! The speed of the drill should not be too fast.

    5. After feeding, try to shake the electric drill, the feeding speed should not be too fast, and add some water to the borehole.

    6. When the glass is drilled through quickly, you must be careful about the feeding speed, which may cause the hole edge to collapse if it is too fast.

    7. After drilling, remove the glass fragments from the glass drill. Then start the next drilling.

Related questions
2 answers2024-07-13

The 50 most commonly used Jing prescriptions (encountered almost every day) - Fuxing Chinese Medicine Network Liu Guantao. >>>More

7 answers2024-07-13

1. Rui. Rui is a Chinese character, pinyin ruì, is the meaning of huiyi, is wise, wise, accessible, wise. The total number of strokes is 14, and the radical is the eye, which can be used as both an adjective and a noun. Original meaning: accessibility; Wise. >>>More

26 answers2024-07-13

You can let your child communicate with others more, enroll him in some extracurricular classes, and communicate with friends of the same age, so that you can slowly open their hearts, or you can raise some pets, and children will slowly open their hearts when they are in contact with pets.

16 answers2024-07-13

Half a year ago, I still used two packs of cigarettes a day, but now half a year has passed, and I really quit smoking, and I didn't smoke a cigarette! Speaking of which, what is the method? I have summarized the following points: >>>More

13 answers2024-07-13

I personally recommend bamboo cotton, which I bought in the summer of 13 years, the fabric is similar to human made, comfortable to wear, but for me I will buy light weight shirts, which are not suitable for matching together, suitable for matching with corduroy fabrics, and if the requirements are not high, you can wear them at will. Muji striped shirts and base layers, a good choice for everyday life. Sunspel is a brand worn by the British royal family, authentic British production, Indian cotton is the starting fabric, the highest island cotton, the base ** is slightly higher, the size is large, especially the armpits are very loose.