How to disassemble the toilet bowl and how to remove the toilet seat

To remove the toilet, check for rupture first, then dismantle the water tank, drain the water in the tank, and dry the toilet. After that, disassemble the base and cut the sealant to remove the toilet, remember to block the drain.

1. Check whether there are cracks on the old toilet first, please pay special attention to the fact that you should start lifting the toilet carefully, most of the toilets are made of ceramic, like glass will cut people, so when moving the toilet, you should wear thick work gloves.

2. Pick up the lid of the water tank - remove the lid of the tank and take the lid to the place where it will not be touched.

3. Turn off the water source, and the position of the water valve is on the left side of the toilet.

4. Flush away the water in the water tank, press the flush handle, let the water run out completely, wear rubber gloves, and use a sponge or towel to dry the water in the water tank that has not flowed away.

5. Use a small disposable container to scoop up the remaining water in the toilet. Use a sponge or towel to dry the remaining water in the toilet.

6. Remove the connecting water pipe from the toilet bowl and pour the remaining water into the bucket.

7. Connect the water tank to the toilet seat. There is a possibility that the bolt will not be removed. It can sometimes take hours to remove the water tank from the toilet seat.

8. Remove the nut and the bolt for fixing. Sometimes the bolt turns, so use a hacksaw to cut the bolt. You can buy a single-handle saw that can be used in areas where space is limited.

9. If your toilet seat is glued to the floor with gap filler, please use a knife to cut the sealant.

10. Shake the toilet quietly to loosen the toilet from the sticky sealant.

11. Ask another person to help lift the toilet. At this point, keep your back straight and use your legs to support the weight. Put the old toilet bowl that has been removed in a place where it will not obstruct the work, and put a rag or towel underneath it, as it will be a little dirty.

Otherwise, you can put it on a rag or plastic sheet and drag it away.

12. Plug the drain pipe with rags to prevent the gas from the sewer from escaping.

13. If the fixing bolts are now broken, they should be removed and replaced.

14. Use a putty knife to scrape off the flange and the old sealant on the floor.

How to disassemble the toilet, the specific steps are as follows:

Step 1: Prepare the tools before disassembling the toilet, generally you need to use a screwdriver, wallpaper, knife, gloves, towels, etc.

Step 2: Remove the lid of the water tank first so as not to hit yourself, close the water valve, and dispose of the water in the tank and toilet.

Step 3: The bucket can be long pressed to flush the button, and the toilet can be scooped out with an old towel or small box.

Step 4: Remove the connecting pipes and connectors from the tank and remove them with a little force.

Step 5: Generally, there will be a circle of glue under the toilet, which is cleaned with a wallpaper knife.

Step 6: Shake the toilet vigorously and ask someone to help you lift it up and place it in a safe place.

Step 7: Plug the drain with rags so that the gas from the sewer does not escape.

The steps to remove the toilet seat and replace it are as follows:

Prepare materials: Rice screwdriver.

1. Remove the fixed screw of the toilet seat.

2. Use a screwdriver to remove the screws on the left side of the toilet lid fixing opening.

3. In the same way, remove the right screw of the fixed opening of the toilet seat.

4. Use both hands to gently lift the toilet lid.

5. The toilet lid has been disassembled.

1.Stand up the toilet lid Stand the toilet lid upright, generally speaking, there is a screw on both sides of the toilet lid for fixing.

2.Loosen the screws Once you have found the screws, use a screwdriver to loosen the screws in the opposite direction, and when they are loose, you can easily lift them up and remove them.

3.One-piece toilet If it is a one-piece toilet lid, you only need to unscrew the set screws on the back of the toilet.

How to remove a domestic toilet seat.

Yes, it won't break.

1. How to dismantle the toilet.

1.First of all, it is necessary to observe whether there are cracks in the toilet, because the toilet is generally made of ceramic, and if there are cracks, it is easy to hurt the construction personnel in the process of removing the toilet. Therefore, wear gloves during construction, and then remove the water tank cover and put it in a place where there is no water, turn off the water source to remove the water in the water tank, and be sure to press the handle of the water tank and do not put it, so that the water can be discharged completely.

2.Use a tool to remove the remaining water from the toilet bowl, and then use a dry rag or sponge to wipe the water inside the toilet bowl dry. Then remove the hose that connects to the toilet bowl and pour the excess water into the bucket.

3.Use a hacksaw to cut the screws connecting the water tank and the toilet, and you can prepare a small single-handle saw to facilitate the use of small spaces. If the toilet is glued to the floor with gap filler, then use a tool to cut the sealant directly, then gently shake the toilet to loosen the sealant, and then lift the toilet bowl, pay attention to keep its back vertically raised, and put it next to it.

At this time, be sure to block the mouth of the drain pipe with rags or other things to prevent the odor of the sewer from running out and debris from falling into the drain.

No matter how the toilet is dismantled, there are some details to pay attention to. For example, before dismantling, it is necessary to determine whether the toilet is drained under the drain or side, and if it is drained, the toilet should be purchased according to the size of the distance from the spout to the wall. If the size of the toilet is too small, it will cause a large gap between the water tank and the wall, and if it is too large, the drain of the toilet will not match the drain outlet.

How do you remove a toilet?

1. How to dismantle the toilet The first step is to check whether the toilet has cracks, it is made of ceramic magnet and is easy to hurt people, and it is necessary to wear protective work gloves when working. First remove the lid of the water tank and place it in a place where there is no water, turn off the water source to flush the water in the water tank, press the flush handle and do not put it, let the water run completely and wear rubber gloves, and use a sponge or towel to dry the water in the tank that has not flowed away.

2. The next step is to use a tool to get rid of the remaining water in the toilet, and then you can use a dry towel or sponge and other absorbent things to dry the inside of the toilet. The bolts may not come out, and it can take hours to remove the tank from the toilet seat. Remove the connected hose from the toilet bowl and pour the excess water into the bucket so that the tank is connected to the toilet seat.

3. We can use a hacksaw to cut off the bolts and disassemble them, and we can buy a single-handle saw to facilitate work and use in a relatively small space. If your toilet bowl is glued to the floor with gap filler, you can use a tool knife to cut the sealant. Gently shake the toilet to loosen the adhesive sealant and lift the toilet again.

What are the precautions for removing the toilet?

1. The waterproof engineering of the toilet at home must be done carefully, especially when the toilet is replaced, the toilet sewer pipe should be waterproofed, because when the old toilet is dismantled, the original waterproof layer is easy to cause damage. Therefore, during the insurance period, it is better to do waterproofing again to avoid unnecessary trouble to the family.

2. Before disassembling the toilet, we must first determine whether the lower drain or the side drain of the toilet at home is clear, so as not to cause the wrong toilet to be purchased and not used. If it is a drain, measure the distance from the drain to the back wall and then buy the toilet according to the size, after the installation of the small size, the toilet tank will leak a large gap from the wall, if the size is large, the drain of the toilet and the drain of the floor drain will not be used.

Then everyone should have an understanding after reading it. In addition, although we know how to remove the toilet, it is necessary to learn the precautions for removing the toilet, but it is recommended that it is better to let a professional get it when replacing the toilet, so that it will be more assured. I hope what is written above can help you and serve as a reference suggestion for you.

The steps to disassemble the toilet are as follows:

1.Turn off the water source: Before disassembling the toilet, you need to turn off the water source to avoid leakage.

2.Drain the water tank: Drain the water in the tank, either by using a pump or by pouring water.

3.Removing the water tank: When disassembling the water tank, you need to remove the water tank cover first, and then remove the screws at the bottom of the water tank to remove the water tank from the toilet.

4.Remove the seat: The seat is the part that connects the toilet bowl to the drain pipe, and you need to use a wrench or a wrench to pull the screw to remove the seat.

5.Disassembling the toilet: To remove the toilet from the ground, you need to remove the screws at the bottom first, and then gently shake the toilet bowl to disengage it from the seat.

Notes:1When disassembling the toilet, it is necessary to pay attention to safety to avoid the toilet from bursting or being damaged.

2.After the disassembly is complete, the toilet bowl and seat need to be placed in a safe place to avoid damage.

3.Before disassembling the toilet, you need to prepare the necessary tools and materials for the dismantling work to be completed smoothly.

Summary. The first step is to close the angle valve and remove the hose, the second step is to cut all the glue at the bottom of the toilet with a blade, and shake the toilet back and forth with your hands, and the toilet will be removed, the third step is to wipe the ground clean, screw the hose on the inlet valve, the fourth step is to put the flange on the connection between the toilet and the sewer, the fifth step is to adjust the flatness of the toilet, the sixth step is to screw the hose on the angle valve, and glue around the toilet.

The first step is to close the angle valve and remove the hose of Fuzishan, the second step is to use a blade to cut all the glue at the bottom of the toilet, and shake the toilet back and forth with your hand, and the toilet will be removed, the third step is to wipe the ground clean, screw the hose on the water inlet valve, the fourth step is to put the flange on the connection between the toilet and the sewer, the fifth step is to adjust the flatness of the toilet, the sixth step is to screw the hose on the angle valve, and glue around the toilet.

First of all, it is necessary to observe whether there are cracks in the toilet, because the toilet is generally made of ceramic, and it is easy to hurt the construction personnel in the process of removing the toilet. Guess the width to Shi Chun Zhaochang to wear gloves, and then remove the water tank cover and put it in a place where there is no water, turn off the water source to discharge the water in the water tank, be sure to press the handle of the water tank, so that the water can be discharged completely. Second, use a tool to remove the remaining water from the toilet, and then use a dry rag or sponge to wipe the water inside the toilet dry.

Then remove the hose that connects to the toilet and pour the excess water into the bucket.

Finally, use a hacksaw to cut the screws connecting the water tank and the toilet, and you can prepare a small single-handle saw to facilitate the use of small spaces. If the toilet bowl is glued to the floor with gap filler, then directly use a tool to cut the sealant, and then gently shake the toilet to loosen the sealant, and then lift the toilet, pay attention to keep the back vertically raised, and put it next to the side after lifting. At this time, be sure to block the mouth of the drain pipe with rags or other things to avoid the smell of the lower liquid ridge waterway from running out and debris falling into the drain.

Nowadays, the toilet has become an indispensable bathroom product in everyone's life, it is easy to use, and it will be safer for the elderly and children at home. Toilets will deteriorate or be damaged after a long period of use, and need to be replaced. So how to disassemble the toilet?

How to disassemble the toilet

1. Check whether the toilet has cracks before disassembly, if there are cracks, it is easy to be injured during disassembly, and protective measures should be taken. Then remove the water tank and turn off the water valve at the same time, flush the water in the tank and clean the inside of the water tank. Next, clean up the remaining water from the toilet bowl and wipe it dry, then remove the water pipe that connects to the toilet.

2. Some toilets and water tanks are tightly connected and difficult to disassemble, so the water tank should be removed first. If it is difficult to disassemble, the bolts can be sawn off with a hacksaw. If caulking glue is used when installing the toilet, the glue should be cut with a tool, and then slowly shake the toilet bowl and lift it gently, so that the toilet bowl is disassembled.

What are the precautions for disassembling the toilet

Waterproofing around the toilet bowl is very important, and the waterproof layer will be somewhat damaged when disassembled. In order to prevent the illusion of water leakage, it is best to apply another layer of waterproofing after the toilet is disassembled. In addition, before disassembling the toilet, you should understand how your pipes are connected, see whether you use the lower or side row, and then choose a suitable new toilet.

How to buy a toilet

It is best to choose a brand for the toilet, because its quality is trustworthy. When purchasing, you can observe the flush button to see if it can be easily rebounded, if the rebound is not flexible or the flush water pressure is not enough, then the quality is relatively poor. When buying a toilet, the flush should be clean first, then the noise should be low, and finally the design should be reasonable and comfortable.

How to disassemble the toilet:

1. Close the water valve and remove the water tank cover.

When disassembling the toilet, first of all, it is necessary to see whether there are cracks on the toilet, it is best to wear gloves to prevent scratches from the surface, and the toilet bowl is relatively heavy to prevent fingers from being pressed. Then close the water valve behind the toilet, and then remove the water tank lid and place it in a spacious place next to it to prevent damage.

2. Drain the water in the tank.

Then rinse the water in the tank, hold down the flush button with your hand all the time, let the water all rinse away, if there is a little water left, you can use a sponge to suck it dry. If there is water in the toilet, you can scoop it out with a small cup or use a sponge to blot it dry.

3. Disassemble the water pipe and water tank.

Then remove the water pipe connected to the toilet bowl and drain the water in the pipe. Then remove the water tank, the water tank is generally bolted, and it should be removed with a screwdriver. If the bolts on the tank will turn and it is difficult to disassemble, you can use a hacksaw to cut it, so that it is very convenient to disassemble.

4. Pry off the sealant underneath.

Usually sealant is used under the toilet, and the sealant connecting the toilet to the floor should be pried open. Then gently shake the toilet with your hands to loosen the sealant underneath, and then the toilet can be lifted.

5. Plug the drain pipe.

After the toilet is removed, it should be placed in a safe place, and if the toilet can be repaired, it may be able to be reused. And it is better to put a piece of paper shell or cloth on the ground, and then put the toilet on top to prevent damage to the bottom of the toilet.

After disassembling the toilet, be sure to block the drain with rags to prevent the gas from the sewer from escaping. And to clean the sealant at the bottom of the toilet, you can scrape it off with a putty knife, otherwise it will affect the appearance.