How to adjust the water volume of the toilet? How to adjust the flush volume of the toilet

1. Adjust the connecting rod.

Open the toilet tank, you can see the black column on the tank, this is the toilet connecting rod, mainly to adjust the toilet button. For better use, it is recommended that the connecting rod should not be too long, as long as it is in contact with the blue and yellow two small pieces under the water tank. During the adjustment process, it is recommended to make the connecting rod one short and one long, and the flushing volume of the toilet will be more moderate.

2. Adjust the overflow pipe.

The long pipe in the toilet box is called the overflow pipe, after the toilet is installed, check the distance between the water level of the water tank and the overflow pipe, under normal circumstances, the water level of the water tank can not be higher than the overflow pipe, if it is found to be too high, it should be adjusted immediately. First, find the white rod in the toilet tank, adjust the white rod to drain the water, and observe the relationship between the water level and the overflow pipe while turning. When you see that the water level is lower than the overflow pipe, you can stop.

3. Adjust the amount of water discharge.

In the toilet tank, in addition to adjusting the overflow pipe and the white rod, there is also an obvious structure that the yellow block moves back and forth, which is also used to adjust the drainage. As the yellow pieces rise and fall, the water displacement of the tank will also change. In the process of adjustment, you can first look at the toilet to see how the drainage is, and then move the yellow block to adjust the drainage.

How it works:

Disassemble the toilet lid and remove it directly.

There are two parts inside the tank, one is the water inlet and the other is the water outlet.

To adjust the water level, you need to adjust the switch of the water inlet, which can be removed and adjusted.

It is also possible to rotate the gears directly.

Rotate the lever clockwise or counterclockwise to adjust the water level of the switch.

Comparing the above figure, you can see that the distance of the gear determines the level of the water. Just reinstall the device to the water inlet.

1. Open the water tank of the toilet.

There are only three parts in total, and the one in the ellipse row is found.

2. Adjust the switch.

Just find the little pillar next to the float.

Don't pull when adjusting, you should rotate it, so that the float position can rise and fall, the float position is the water level, and the water level is high, and the water volume will naturally be large.

The toilet flush is controlled by a limit (float), and when the water in the tank rises to a certain position, the float that controls the water will automatically turn off the water supply. When you put bricks in the toilet, the water level in the tank will be raised, so that the float will reach the position where it can stop filling the water in advance, and the amount of water will be reduced a lot.

The parts in the tank can be adjusted as long as they can be adjusted.

How to adjust the amount of toilet flush volume

Step 1: Open the toilet tank lid and unscrew the drain valve directly.

Step 2: There are two small mechanisms on the drain valve of the toilet, which are the two scales on it, which are used to adjust the amount of water; The two scales correspond to the two buttons on the toilet, which are full drainage (white) and semi-drainage (blue), and there is a gear, the higher the gear, the lower the water level; We only need to adjust the white button under the full drain to the bottom 1 gear, and the water output will be large and violent.

Step 3: The blue button corresponding to the semi-drainage is also adjusted to the lowest, and the problem of small water output is easily solved.

Ways to save toilet flush water

1. You can prepare a bottle of mineral water filled with water, and put it in our water storage tank after the lid is tight, so that the amount of water in one bottle of water will be reduced every time you flush it, and if the water storage tank is relatively large, you can stuff one more bottle of mineral water bottle.

2. You can also put two stone bricks in the water storage tank, which can reduce the amount of water discharge by the same principle as the water bottle.

3. Bend the float handle in the water tank down a little to reduce the flushing volume of the toilet.

Automatic toilet flush size adjustment method 1, first open the lid on the automatic toilet tank, you will see that there are two mouths, one is water inlet and the other is water outlet. 2. Remove the water inlet and find the regulating valve that adjusts the water level inside. 3. Rotate the gear clockwise, you can raise the water level, but the design of each brand is different, some are dialed up and down, if it is this kind of flush toilet, if you want to increase the flushing strength, you have to dial down, and lowering the water level is to dial up.

4. There is also a white cylinder in the water tank of some flush toilets, there will be different units on the cylinder, and the two blue gears can be adjusted to the size of the gear, and the upward adjustment is to raise the water level.

Hello, automatic toilet flush volume adjustment method: Step 1: Open the toilet tank lid and unscrew the drain valve directly.

Step 2: There are two small mechanisms on the drain valve of the toilet, which are the two scales on it, which are used to adjust the amount of water; The two scales correspond to the two buttons on the toilet, which are full drainage (white) and semi-drainage (blue), and there is a gear, the higher the gear, the lower the water level; We only need to adjust the white button under the full drain to the bottom 1 gear, and the water output will be large and violent. Step 3:

The blue button corresponding to the semi-drain is also adjusted to the lowest, and the problem of small water output is easily solved. 

When installing the toilet, there is a valve next to the bathroom. We can adjust the size of the valve according to the water consumption of the household to control the water consumption of the toilet.

First of all, you need to open the lid of the toilet, and after opening, you only need to adjust the two drain valves, and the upper buttons are all adjusted to the bottom.