How do you want to adjust the flush volume of the toilet?

The frequency of use of the toilet is relatively high, and the flushing volume is closely related to the cleanliness, if the flushing volume is too large, it is easy to waste water, but the water bill is relatively high after a long time, and it is not cost-effective. However, if the toilet does not flush enough, it cannot be cleaned, which is very uncomfortable. So how do you adjust the flush volume in the toilet?

To adjust the flushing amount of the toilet at home, first lift the toilet lid and you can see two round bumps in the tank.

These two round bumps are also known as full drainage and semi-draining, as the name suggests, the total drainage is sufficient, and the semi-drainage is not very much. It is usually possible to adjust the two pimples to the midpoint, which is more water-efficient and at the same time easy to use. Open the toilet tank, you can see the black column on the tank, this is the toilet connecting rod, mainly to adjust the toilet button.

For better use, it is recommended that the connecting rod should not be too long, as long as it is in contact with the blue and yellow two small pieces under the water tank. During the adjustment process, it is recommended to make the connecting rod one short and one long, and the flushing volume of the toilet will be more moderate.

The long pipe in the toilet box is called the overflow pipe, after the toilet is installed, check the distance between the water level of the water tank and the overflow pipe, under normal circumstances, the water level of the water tank can not be higher than the overflow pipe, if it is found to be too high, it should be adjusted immediately. First, find the white rod in the toilet tank, adjust the white rod to drain the water, and observe the relationship between the water level and the overflow pipe while turning. When you see that the water level is lower than the overflow pipe, you can stop.

In the toilet tank, in addition to adjusting the overflow pipe and the white rod, there is also an obvious structure that the yellow block moves back and forth, which is also used to adjust the drainage. As the yellow pieces rise and fall, the water displacement of the tank will also change. In the process of adjustment, you can first look at the toilet to see how the drainage is, and then move the yellow block to adjust the drainage.

When installing the toilet, there is a valve next to the bathroom. We can adjust the size of the valve according to the water consumption of the household to control the water consumption of the toilet.

First of all, you need to open the lid of the toilet, and after opening, you only need to adjust the two drain valves, and the upper buttons are all adjusted to the bottom.

How to adjust the amount of toilet flush volume

Step 1: Open the toilet tank lid and unscrew the drain valve directly.

Step 2: There are two small mechanisms on the drain valve of the toilet, which are the two scales on it, which are used to adjust the amount of water; The two scales correspond to the two buttons on the toilet, which are full drainage (white) and semi-drainage (blue), and there is a gear, the higher the gear, the lower the water level; We only need to adjust the white button under the full drain to the bottom 1 gear, and the water output will be large and violent.

Step 3: The blue button corresponding to the semi-drainage is also adjusted to the lowest, and the problem of small water output is easily solved.

Ways to save toilet flush water

1. You can prepare a bottle of mineral water filled with water, and put it in our water storage tank after the lid is tight, so that the amount of water in one bottle of water will be reduced every time you flush it, and if the water storage tank is relatively large, you can stuff one more bottle of mineral water bottle.

2. You can also put two stone bricks in the water storage tank, which can reduce the amount of water discharge by the same principle as the water bottle.

3. Bend the float handle in the water tank down a little to reduce the flushing volume of the toilet.

Hello, automatic toilet flush volume adjustment method: Step 1: Open the toilet tank lid and unscrew the drain valve directly.

Step 2: There are two small mechanisms on the drain valve of the toilet, which are the two scales on it, which are used to adjust the amount of water; The two scales correspond to the two buttons on the toilet, which are full drainage (white) and semi-drainage (blue), and there is a gear, the higher the gear, the lower the water level; We only need to adjust the white button under the full drain to the bottom 1 gear, and the water output will be large and violent. Step 3:

The blue button corresponding to the semi-drain is also adjusted to the lowest, and the problem of small water output is easily solved. 

Automatic toilet flush size adjustment method 1, first open the lid on the automatic toilet tank, you will see that there are two mouths, one is water inlet and the other is water outlet. 2. Remove the water inlet and find the regulating valve that adjusts the water level inside. 3. Rotate the gear clockwise, you can raise the water level, but the design of each brand is different, some are dialed up and down, if it is this kind of flush toilet, if you want to increase the flushing strength, you have to dial down, and lowering the water level is to dial up.

4. There is also a white cylinder in the water tank of some flush toilets, there will be different units on the cylinder, and the two blue gears can be adjusted to the size of the gear, and the upward adjustment is to raise the water level.

The adjustment method of small toilet flush pressure is as follows:

1. Water tank type: There is a toilet with a water tank at the rear, when flushing, the water always feels weak, and the water volume in the water tank can be improved by adjusting it. As for the switch at the back of the toilet, it is to adjust the amount of water inlet into the water tank, regardless of the flushing force.

2. Pressure type: it will flush when pressed by the wrench (there is no water tank at the back of the toilet), not "there is a switch behind the toilet that can be turned by a vise".

Instead, there is a screw with a circular slotted hole threaded hole on the adapter next to the pipeline next to the pressure spring barrel (the same as the shower head and the wall elbow to adjust the size of the water outlet), and turning to the right with a slotted driver will cause a large amount of water to flush.

Which flush effect is better in the toilet

1. Straight flush type

The flush toilet is to rely on the momentum of the water flow to discharge our poop, the wall of the toilet is relatively steep, the water storage area is small, the water power is concentrated together, the impact force is large, and the flush is very clean.

2. Siphon type

The siphon toilet pipe is a "" type, if the pipe drains for a long time, there will be a lot of scale in it, and there is a certain gap in the water level.

Because the siphon toilet flushing is with the help of water impulse, the water area in the pool is relatively large, and the flushing sound is also very small. There are two types of siphon toilets, one is a vortex siphon and the other is a jet siphon.

3. Vortex siphon

The flush port of the toilet of the vortex siphon is at the bottom of the toilet, and the water flow is formed along the pool wall when flushing, so that the flushing of the pool wall is increased, and the suction power is also increased, and it is easier to discharge the internal organs of the toilet, so that the toilet is kept clean and tidy, and it is not easy to breed bacteria.

4. Jet siphon

Jet siphon is the use of the principle of siphon, on the toilet has been transformed, but at the bottom of the toilet added a jet secondary channel, aimed at the center of the sewage outlet, when flushing, part of the water flows out from the cloth hole around the toilet circle, one is sprayed out from the jet port, the water flow of this toilet is very large, and the stains can be flushed away quickly, and there is no need to worry about not flushing clean, smelling and other problems.