How to remove the trademark glue on stainless steel basins?

1. How to remove the glue stuck to the stainless steel basin.

1. We soak the stainless steel basin with warm water, and then tear off the self-adhesive label on the basin, and the residual label can be wiped clean repeatedly with a cloth dipped in a little soapy water, and finally rinse the stainless steel basin with water. Or use a hair dryer to blow the label for a while, and then tear it off completely, pay attention to be patient when tearing, do not pull and tear violently, so as not to have residual self-adhesive.

2. If there is wind oil essence or nail polish remover at home, it can also be used to remove the self-adhesive label on the stainless steel basin, we will drop the wind oil essence or nail polish remover on the self-adhesive label, let it stand for a few minutes, and wipe it with a cloth. For example, hand cream, facial cleanser, vinegar, etc. can also remove self-adhesive labels from stainless steel basins.

Second, how to clean and use stainless steel basins.

1. The stainless steel basin is relatively simple to clean, for example, we can easily remove the dust on the surface and the dirt that is easy to remove with soapy water. If there is drifting agent on the surface of the stainless steel basin, we can clean it with a neutral washing liquid. If the stainless steel basin is rusty, you can wipe it off with sandpaper or use abrasive detergent to clean it.

Note that the stainless steel basin cannot be cleaned with strong alkali and strong oxidizing detergent.

2. In daily life, it is best not to store corrosive items in the stainless steel basin for a long time, otherwise it will cause damage to the stainless steel basin, and the items with strong acid and alkali will react with stainless steel, which will have a certain impact on the human body. Stainless steel basins cannot be used to boil traditional Chinese medicine, which will not only affect the efficacy of the medicine, but also produce harmful substances.

Soak the wind oil essence into the label, gently scrape off the soft part of the bubble, repeat the action several times, and in about 2 minutes, a piece of self-adhesive will be cleaned off. Then wipe it with a clean cotton cloth, and the sticker will come off.

Trademarks on stainless steel devices are generally made of paper material. You can use dish soap or an alcohol-based solution to dissolve and erase it.

Do not peel off the trademark on the stainless steel basin directly, do not blister with water, use a hair dryer to blow on the side without a label for a while, when the temperature reaches 60 70 degrees, gently uncover a corner, and slowly tear it off. Then wipe it with alcohol, wash it with water, and you can use it.

Tear off after a little heat (e.g., blowing a hair dryer for a while);

If there is any residual glue, you can apply some oil (vegetable oil, wind oil essence...).Soak for a while and wipe off with a scouring pad.

Heat it with a hair dryer first, and then it's easy to tear.

Hair dryer: Use a hair dryer to blow hot air on the label on the basin, blow for about 1 minute, gently tear off by hand, you can remove the label completely, without any traces. Apply the wind oil essence to the offset printing of the label, apply it evenly and leave it for one minute.

Then wipe it with a damp towel and it will be as clean as new. <

1. Hair dryer: Use a hair dryer to blow the hot air on the trademark on the basin, blow for about 1 minute, and gently tear off the label by hand, you can completely remove the label without any traces.

2. Apply the wind oil essence to the offset printing of the label, and leave it for one minute after applying it evenly. Then wipe it with a damp towel and it will be as clean as new.

3. Pour the liquor on the paper towel, and then put the paper towel on the label, stay for 5 minutes, after the time is up, directly remove the paper towel, the label can also be removed, the alcohol component in the liquor can dissolve the organic glue in the label, and the white vinegar can also be used to remove the label with the same operation.

Here's how to remove the label glue from the basin:1. First of all, pour an appropriate amount of boiling water on the label at the bottom of the newly bought stainless steel basin, and scald the label of the basin to soften.

2. Next, tear off the label at the bottom of the newly bought stainless steel basin and tear it until only the glue remains.

3. Wait for all the labels to be removed from the silver to the bottom of the stainless steel basin and wipe the water in the basin dry with a paper towel. Spike feast.

4. Then prepare several sections of waterproof tape as shown in the figure below, and pay attention to the waterproof tape not to get wet.

5. Next, use waterproof tape to repeatedly glue out the remaining glue stains on the stainless steel basin label as shown in the figure below.

1. Use a hair dryer to blow hot air on the label on the basin and blow for about 1 minute.

2. Gently tear off the hand, you can completely remove the label without any traces. This method does not damage newly purchased items and works well. If you have already torn half of it and it is very sticky, then use what we commonly call "wind oil essence" to rub a few more times on that place, and look at method 2 for details, it will be completely removed.

3. Apply the wind oil essence to the offset printing of the label.

4. Spread the wind oil essence evenly on the label.

5. Spread evenly and leave it for one minute.

6. Then wipe it with a wet towel, and you can see that it is very clean.

7. Pour the liquor onto a paper towel.

8. Then apply this tissue to this label. The alcohol component in the liquor is able to dissolve the organic glue inside the label.

9. Stay for 5 minutes, when the time is up, we will directly remove the tissue, and the label can also be followed. Very clean. The same can be done with white vinegar to remove labels.

1. There are the following six ways to remove the trademark of the plastic basin:

2. Blow with a hair dryer for a while, the glue will melt after heating, and it can be easily removed. If there are still some traces that cannot be removed, you can apply it with wind oil essence in the middle of the attack, and it will be cleared relatively cleanly.

3. Wipe with a paper towel dipped in some alcohol, and then rub it a few times to be clean.

4. Use acetone, the method is the same as above. The amount is small and thorough, and the best thing is that it removes these residual gums very quickly and easily, which is better than alcohol.

5. Use nail polish remover. The usage is the same as alcohol acetone. The effect is also very good. Nail polish remover does not require quality, good or generally fine, as long as it can wash off the nail polish.

6. Use hand cream. Tear off the printed products on the surface first, then squeeze some hand cream on it, and slowly rub your brother's thumb, and rub it for a while to rub off all the sticky residues. It's just a little slower.

Hand cream is an oily substance, and its properties are incompatible with glue. This is the use of this property for glue removal.

7. Banana water is an industrial agent used to remove paint, and it is easy to buy, and the method is the same as alcohol acetone.

8. It is difficult to remove the trademark that has been used for a long time, so you can use a hair dryer to heat it to soften it and remove the film, and then use rosin perfume to wash off the residual adhesive on the glass.

First, pour in boiling water, blanch this label until soft, and wait for about a minute. Quickly peel off the label paper until only the glue remains. Find a little waterproof tape and cut a few sections with scissors.

Then use toilet paper to wipe the water on top of the remaining glue. Glue a piece of waterproof tape to the residual adhesive, press the tape vigorously, then lift the tape vertically up with both hands, and repeat until the glue is finished. You can remove the label glue on the stainless steel.

1. First pour in boiling water, blanch this label until soft, and wait for about a minute.

2. Quickly tear off the label paper until only the glue remains. Find a little waterproof tape and cut a few sections with scissors.

3. Then use toilet paper to wipe the water on the residual glue dry.

4. Take a piece of waterproof tape and stick it to the residual glue, press the tape vigorously, and then lift the tape vertically up with both hands, and repeat this action until the glue is finished.

5. You can remove the trademark glue on the stainless steel.

Label offset printing method for removing stainless steel discs:

1. Tools and raw materials.

Scissors, waterproof tape (sold at hardware stores).

Hot water, toilet paper.

Second, the method steps.

1. First of all, we pour a little boiling water and soften the label for one minute.

2. Then, we quickly peel off the label paper by hand and tear it off quickly until it leaves only glue.

3. Then, we find a small waterproof tape, cut a few sections with scissors, and place it in the stainless steel basin (be careful not to let the water on the waterproof tape).

4. Then, we use toilet paper to dry the water on the residual glue, and it must be wiped clean. Otherwise, the tape becomes ineffective when exposed to water.

5. We put a piece of waterproof tape on the residual glue watermark, press the tape hard to make it stick, and then lift the tape directly up with both hands, and repeat the action repeatedly until the cut tape is used up.

6. In this way, we use waterproof tape, and the glue watermark remaining on the stainless steel container is quickly removed, which is a safe and fast method.