How to disassemble an ordinary household hair dryer, how to disassemble a hair dryer How to disassem

1. First of all, you need to prepare the dismantling tool, as shown in the figure below.

2. You need to find the two screw holes on the handle of the hair dryer below, as shown in the figure below.

<>4. The following places need to be removed from the power cord connection, as shown in the figure below.

<>6. Use pliers below.

Drag out the generator of the hair dryer, as shown in the figure below.

7. Then disassemble a layer of tin foil on the outside of the development motor.

Yes, as shown in the figure below.

8. Finally, the disassembly of the hair dryer is completed, as shown in the figure below.

<>2. Then find the two screw holes on the handle.

3. Unscrew the two screws on the handle and open them gently to prevent something like a spring from flying out.

4. Remove the place where the power cord is connected, you can see a simple switch and two not-so-healthy power cords.

5. After taking them all out, pinch the two thin things behind with one hand and two fingers and open the lid at the back.

6. Pull the generator out with pliers.

7. Disassemble the outer layer of tin foil or something.

8. Finally, the dismantling is completed, as shown in the figure below.

Hehe, I want to fix it myself.

Hair dryers are different, depending on which one you are. Most common hair dryers, if you only want to remove the handle, don't move the screws on the hair dryer, otherwise it will be troublesome to restore. Similarly, if there is a problem in the hair dryer, do not disassemble the handle part.

The heating wire in the hair dryer is red, the wind is small, there is no hot air, there is no wind but the heating wire is hot and red, which is generally a fault in the hair dryer, only dismantle the hair dryer. When disassembling, the screws on the left and right sides of the hair dryer should not be completely twisted out, twist out half, and then carefully pull out the front half of the hair dryer. There is no reflection when the power is turned on, and the power cord at the handle is generally broken.

Only the handle is removed. Switches are less broken.

<>1. Clamp both sides of the fan shaft hole with needle-nose pliers and pull out the fan blades;

2. Wrap a small section of single-strand copper wire around the soldering iron head a few times, leave a section to insert into the fan shaft hole, resist the fan motor shaft to heat the motor shaft for about 1 minute, and then use needle-nose pliers to pull out the fan blade;

3. Do not use too much force when clamping the blades with needle-nose pliers, so as not to crush the plastic blades. The blades are installed with a hot sleeve process, so some are very tight and can't be pulled out, when heating with an electric soldering iron, try not to burn the plastic blades and overheat.

The steps for the hair dryer are as follows:Material preparation: hair dryer, screwdriver.

1. There are generally screws on the handle of the hair dryer, so remove the screws on the handle first.

2. The others are basically buckled, and there are no screws. So you just need to find the right place to buckle it up.

3. Below are all the parts after turning on the hair dryer.

The specific steps of disassembling the hair dryer are as follows:

Tools: hair dryer, screwdriver.

1. Find the two screw holes on the handle.

2. Unscrew the two screws on the handle and open them gently to prevent something like a spring from flying out.

3. Remove the place where the power cord is connected, and you can see a simple switch and two power cords.

4. After all the troubles come out, pinch the two thin things behind with one hand and two fingers, open the lid at the back, and pull the generator out with pliers.

5. After disassembling the outer layer of tin foil and the like, the hair dryer is disassembled.

1. Be sure to disconnect the power supply and prepare a screwdriver when dismantling. Find the screw knob of the hair dryer handle and remove the screw.

2. Dismantle the protective cover, the clip bite is very in place, basically a disposable product, and it is not easy to remove good makeup.

3. When dismantling, you must pay attention to it, you can't use a screwdriver to pry hard, just take it off carefully by hand, and be careful to hurt your hands when you take it off. Remove the casing on the rear of the fuselage to completely open the casing of the hair dryer. Tips:

You must not change the line by yourself and increase the power of the hair dryer, which may bring unnecessary trouble, and you must pay attention to safety when dismantling.

1. First of all, you need to prepare the dismantling tool, as shown in the figure below.

2. The following needs to be disassembled and then find the two screw holes on the handle of the hair dryer, as shown in the figure below.

<>4. The following places need to be removed from the power cord connection, as shown in the figure below.

<>6. Use pliers to pull out the generator of the hair dryer below, as shown in the figure below.

7. Then disassemble a layer of tin foil on the outside of the development motor, as shown in the figure below.

8. Finally, the disassembly of the hair dryer is completed, as shown in the figure below.