How to disassemble the hair dryer, how to disassemble the hair dryer

When disassembling the hair dryer, you must find out the structure of the hair dryer, and the steps are as follows:

1. Prepare the disassembly tool and find the two screw holes on the handle.

2. Unscrew the two screws on the handle and open them gently to prevent something like a spring from flying out.

3. Remove the place where the power cord is connected, you can see a simple switch and two power cords.

4. After taking them all out, pinch the two thin things in the back with one hand and two fingers, open the lid at the back, and pull the generator out with pliers.

5. After disassembling the outer layer of tin foil and the like, the hair dryer is disassembled.

1. Boring dehumidification. Families with babies always can't dry when it rains. Use a hair dryer.

Blow it, it works well.

2. Electrical dust removal. After household appliances are immersed in water or damp, they can use a hair dryer to drive away the moisture; In the case of power failure, the back cover of household appliances with dust accumulation can be turned open, and the dust can be blown away by a hair dryer and cool breeze to avoid short circuit and high-voltage breakdown, and extend the service life of the appliance.

3. Correct the refrigerator seal. After the refrigerator has been used for a long time, the door seal will deteriorate and become uneven. Use a hair dryer to blow on the original depression of the local area can be restored to its original state, and then cover it with a cold towel to cool it down, repeat it a few times, and the door seal will be repaired.

4. Defrost the refrigerator. If the refrigerator needs to be defrosted for a long time each time, if you open the freezer door, use a hair dryer to blow hot air inside.

The time of defrosting can be shortened, and the intention of rapid defrosting can be achieved.

5. Stop bleeding. In ordinary days, if you accidentally cut a part of your body and bleed, you can immediately use a hair dryer to blow hot air to the wound, which can scab over and stop bleeding in a short time, which is of great help to avoid trauma infection and speed up wound healing.

6. Health care. Have low back pain or frozen shoulder.

Before applying the plaster, you can blow the handle with a hair dryer for a while, and then apply the plaster after a little massage, which has an obvious healing effect. In addition, use a hair dryer to target the affected area and insist on blowing hot air at appropriate intervals for 5 to 10 minutes each time to reduce the pain.

7. Insect control. Aim the hair dryer at the holes and cupboards.

If the gap in the table is blown, the ants and nails will run out when the heat is unbearable, and they can be destroyed in one fell swoop.

8. Anti-mildew and insect prevention. Books, stamps, photo albums, etc. can often be blown by a hair dryer for a while, which can repel moisture, mildew, insects, and paper yellowing.

The steps for the hair dryer are as follows:Material preparation: hair dryer, screwdriver.

1. There are generally screws on the handle of the hair dryer, so remove the screws on the handle first.

2. The others are basically buckled, and there are no screws. So you just need to find the right place to buckle it up.

3. Below are all the parts after turning on the hair dryer.

How to disassemble the SOOC S hair dryer.

Hello, dear, according to your description, how to disassemble the SOOC S hair dryer; 1. To remove the shell, we first rotate and remove the hair dryer nozzle and back cover. Next we find the set screw at the hair dryer housing and loosen it with a screwdriver to remove it. Finally, we will break the front and rear shells of the hair dryer, if it is not easy to disassemble, we can use a slotted screwdriver to pry along the gap between the front and rear shells to separate the front and rear shells.

2. The accessories of the hair dryer can be divided into three parts: motor, heating wire and switch module. We can directly pull out the switch module at the handle and remove the wires at the switch module block with a screwdriver. Then we use a screwdriver to loosen the motor fixing screws, pull out the motor and the heating wire, and then disassemble the wires connected to the heating wire and the motor to separate them.

Step 1: Lay the hair dryer flat, and you can see that there is a rotating buckle at the connection between the nozzle and the hair dryer.

Step 2: Under normal circumstances, the buckle is stuck clockwise, so it needs to be rotated counterclockwise to open.

Step 3: Gently and forcefully rotate counterclockwise, feel the buckle is loose, and the nozzle can be removed.

Step 4: In the same way, if you need to install other functional heads of the hair dryer, you only need to align the barrel.

Step 5: After screwing it clockwise, it can be used normally.

1. Be sure to disconnect the power supply and prepare a screwdriver when dismantling. Find the screw knob of the hair dryer handle and remove the screw.

2. Dismantle the protective cover, the clip bite is very in place, basically a disposable product, and it is not easy to remove good makeup.

3. When dismantling, you must pay attention to it, you can't use a screwdriver to pry hard, just take it off carefully by hand, and be careful to hurt your hands when you take it off. Remove the casing on the rear of the fuselage to completely open the casing of the hair dryer. Tips:

You must not change the line by yourself and increase the power of the hair dryer, which may bring unnecessary trouble, and you must pay attention to safety when dismantling.