How to disassemble the flash grid hair dryer? How to disassemble the flashed hair dryer

2. Then find the two screw holes on the handle.

3. Unscrew the two screws on the handle and open them gently to prevent something like a spring from flying out.

4. Remove the place where the power cord is connected, you can see a simple switch and two not-so-healthy power cords.

5. After taking them all out, pinch the two thin things behind with one hand and two fingers and open the lid at the back.

6. Pull the generator out with pliers.

7. Disassemble the outer layer of tin foil or something.

8. Finally, the dismantling is completed, as shown in the figure below.

Nowadays, hair dryers widely use the buckle design, although there are no screws, you can see obvious gaps, wrap them with cloth and tap them hard, and when the gaps become larger, you can pry them open with a hard plastic sheet.

There is a high probability that there are screws at the handle position, which are generally hidden under the label, pay attention to remove)

Flashing, on behalf of the power bank internal charging circuit board working in a high-current charging state, once the internal charging battery voltage reaches a certain value, the charging indicator will advance one grid, when it reaches more than three grids (note, my charging treasure flashes three grids and four grids do not flash), the charging current decreases, and it will trickle small current charging. There is still a fault in the voltage detection of your power bank, or there is a problem with the voltage indicator circuit, if you can find the manufacturer to replace it, it is best to use it.

Hit it with a hammer, and if it doesn't work, turn the mouth of the hair dryer and open it.

Even lucy!

First disassemble the outer fixing screws of the flashed hair dryer, disassemble the shell of the flashed hair dryer, and remove the internal parts.

1 Find the two screw holes on the handle, 2 Unscrew the two screws on the handle and open.

3. Remove the place where the power cord is connected, and you can see a simple switch and two not-so-healthy power cords.

4After taking them out, pinch the two thin things behind with one hand and two fingers, and open the lid on the back.

5. Pull the generator out with pliers.

6. Disassemble the outer layer of tin foil or something.

7. Dismantling is complete.

How to disassemble the flashing hair dryer, hello! 1. Prepare to disassemble the tool 2, find the two screw holes on the handle 3, unscrew the two screws on the handle and open them gently to prevent something like a spring from flying out 4. Remove the place where the power cord is connected, you can see a simple switch and two unhealthy power cords 5, after all are taken out, hold the two thin things behind with two fingers of the punch hand, open the back cover and judge the good sub 6, use pliers to pull the generator out 7, disassemble the outer layer of tin foil and the like8, In order to make the hair dryer play the effective role of drying and shaping, to achieve correct, reasonable and safe use, and to prolong the life of the appliance, the following matters should be paid attention to when blowing: (1) The hair dryer must be used under the power supply voltage specified on the nameplate.

For hair dryers with three-wire power cords, the grounding wires should be properly connected. (2) When using the hair dryer, the air inlet and outlet must be unobstructed, otherwise it will not only fail to achieve the use effect, but also cause overheating and burn out the utensils. (3) When used to dry wet hair, the air outlet of the hair dryer should be kept at a certain distance (not less than 50mm) from the hair to prevent blocking the air outlet and burning the hair.

At the same time, it is important to keep a certain distance to avoid water vapor generated when drying hair that affects the dielectric strength and cause leakage. (4) Before the end of use, try to switch the hair dryer from the "hot" to the "cold" mode first, so as to cut off the power supply of the electric heating element first. Then let the remaining heat of the electric heating element be blown out by the cold air, so that the internal temperature of the electric hair dryer will be reduced, and then all the power will be cut off.

This slows down the aging of the internal insulation of the hair dryer and prolongs the service life. At the same time, it is not easy to burn other objects when placed on the table. (5) Try not to use the hair dryer for too long in continuous sections, and should be used intermittently to avoid overheating and burning out of the electric heating element and motor.

When the electric hair dryer is not in use, it should be placed in a dry place, and should not be placed in the open air or wet place, and when it is taken out after long-term use, the insulation resistance should be checked first, and it can be used normally under the requirements to ensure personal safety during use. Due to the presence of dust in the air, although many hair dryers have a filter at the air inlet to protect them, they cannot prevent dust with very small particles, and not all hair dryers have a filter cloth. For this purpose, dust must be cleaned regularly to prevent clogging of the air ducts and damage to the elements.

6) Do not throw the hair dryer at will, the electric heating element and the motor will be damaged by mechanical impact, and do not disassemble it easily to avoid damaging the parts. In order to ensure the normal use of the electric hair dryer, the bearing part of the motor and other rotating parts should be regularly lubricated, but the amount of oil should not be too much, so as not to flow to the coil and cause failure. Hope it helps!

1.There are generally screws on the handle of the hair dryer, so the dust stool should remove the screws on the handle first. 2.

The rest is basically buckled, and there are no screws. So you only need to find a suitable place to buckle it, and generally buckle it tightly, pay attention not to hurt. 3.

In fact, there is not much after opening, you can check to see what is broken, and then connect the terminals, change the wire or something.

1. To remove the shell, we first rotate and remove the hair dryer nozzle and back cover. Next, we find the fixing screw at the housing of the blowing loss and width machine, and loosen it with a screwdriver to remove it. Finally, we will break the front and rear shells of the hair dryer, if it is not easy to disassemble, we can use a slotted screwdriver to pry along the gap between the front and rear shells to separate the front and rear shells.

2. The accessories of the hair dryer can be divided into three parts: motor, heating wire and switch module. We can directly pull out the switch module at the handle and remove the wires at the switch module block with a screwdriver. Then we use a screwdriver to loosen the motor fixing screws, pull out the motor and the heating wire, and then disassemble the wires connected to the heating wire and the motor, and sell them separately.

Summary. Disassembling a flash-frame hair dryer requires care to ensure you understand the location and function of the individual components. If you are not sure how to disassemble your hair dryer, it is recommended that you seek the help of a professional.

Disassembling a flash-top hair dryer requires care to ensure you understand the location and function of the individual components. If you are unsure how to disassemble the hair dryer, we recommend that you seek professional help.

I'm still a little confused, can you be more detailed?

If you need to disassemble the flash-frame hair dryer, you need to pay attention to the following steps:1First, disconnect the power supply and wait for the hair dryer to cool down so as not to burn yourself.

2.Use a screwdriver to remove the housing of the hair dryer, usually there are several screws on the casing, and you need to remove them all. 3.

Once you remove the case, you will see the circuit board and motor inside the hair dryer. If you need to replace the motor or other parts of the cavity, you can remove them. 4.

If you need to replace the circuit board, you will need to remove the connecting wires from the board first, and then remove the circuit board from the inside of the hair dryer. 5.If you need to replace the fan blades, you can use a wrench to remove the fan blades and install the new ones on the shed hair dryer.