Is it possible to change the oil yourself without the tools?

If you don't have these things, you should go to the repair shop, don't toss around, the car will be more than worth the loss, it is best to bring it yourself, there are many fakes in the auto repair shop. However, the cost performance of their own maintenance is really high, and I now also buy imported GT magic red engine oil on the Internet, and now it is more than 10,000 kilometers to change once, and the rapid acceleration is much cooler than the original engine oil before The engine sound is not harsh. Much better than the original oil.

Start by jacking the vehicle up, and it's a good idea to have wedge-shaped wood to support the vehicle in case the jack suddenly comes loose. Then we find the drain bolt, unscrew the oil, and pay attention to the oil temperature to prevent burns. At the same time, you must let the oil drip for a while, so that it will be cleaner.

When we find that the oil is cleaned, we can screw back the oil drain bolts, taking care not to tighten it too much to prevent damage to the oil pan. Then we can unscrew the filter element and put the container under the oil filter. If the temperature of the filter is too high, wear gloves.

At the same time, be careful not to damage the interface screws on which the filter is installed and the components around the filter. Then we can refer to the manual on board to select the appropriate oil filter, and remember to apply new oil to the interface gasket of the new filter. As a side note, if the filter is installed vertically, add some fresh oil to the filter so that dry grinding can be reduced the next time the engine starts.

Immediately after that, we can screw in and tighten the oil filter, and the way to tighten the oil filter is usually to tighten it and then screw it in 3 or 4 turns. Finally, it is time to add a new engine oil, and we need to choose the right oil according to the manual that comes with the vehicle. And to prevent oil leakage to the outside of the engine, a funnel can be used.

After adding oil, we need to check the lower part of the engine for leaks, and if everything is in order, then we can pack up our tools. Finally, there are a few points that we need to pay attention to when buying engine oil. First of all, there is no need to use a higher grade oil, nor can you use a lower grade oil on a more demanding engine.

At the same time, some domestic brand engine oil is already quite good, and it is relatively cheap, which can be considered. Finally, low viscosity oil should be chosen when the temperature is low in season; High viscosity oil should be selected in the hot season or when the engine is severely worn.

I don't think we can change the oil of the car by ourselves, because it will bring us a lot of unnecessary trouble, and it is not conducive to ensuring the safety of our lives, so I think the oil of the car should not be changed by ourselves.

Yes, but you need to understand the way to change the oil, and you also need to have the skills to change the oil, and when you change the oil, you must choose the right oil.

No, there is a certain danger in doing so, it may affect the life of the engine, and there may be some impurities.

The tools needed to change the oil by yourself are: 1. Lifting equipment (lift or replacement bracket); 2. an oil filter element wrench; 3. an oil-draining screw wrench; 4. Connect the waste engine oil basin. Extended Materials.

Steps to change the oil:

1. Choose a flat ground and align the bracket with the wheels of the car. 2. Drive the front wheel of the car to the bracket and prepare to change the oil. It's better to have a companion outside to command here.

3. Find the oil drain screw, place the waste oil basin under the screw, and use a special wrench to loosen the oil drain screw. 4. Open the oil cap above the engine and unscrew the screws to make the oil flow out quickly.

5. Replace the filter element with a new filter element with a special wrench.

6. When there is no waste oil flowing out of the oil drain screw, tighten the oil drain screw. Add new oil above the engine.

7. When adding engine oil, it should be controlled between the upper and lower engraved lines of the oil dipstick.

The oil change is complete.

It is not recommended to change it yourself, you have to start the car first to change the oil, and then there is a bolt on the chassis under the engine, and you can release the oil if you unscrew it But because the temperature will be very high, it is easy to be injured without experience, and the oil that is changed is not easy to handle. If you don't want to use the original oil, you can bring your own oil. I am now bringing my own imported G T Magic Red engine oil, bought on the official website, there are no fakes, the quality is good, the reputation is good, and the cost performance is very high.

To change the oil by yourself, you need to loosen the wrench of the oil pan drain screw, the wrench to replace the oil filter element, the rag, the jack, and the oil basin, and the specific operation steps for changing the oil are as follows

1. Use jacks to lift vehicles.

3. Loosen the oil pan drain screw.

4. Drain the oil.

5. Tighten the oil drain screws.

6. Unscrew the filter element.

7. Replace it with a new filter element.

8. The introduction of new engine oil is completed.

Hello, you need to lift the car, you need to use an oil grid wrench, you need a common tool to remove the oil pan oil drain screw.

1.Lifting equipment (lifts or changing brackets);

2.oil filter element wrench;

3.oil-draining screw wrench;

4.Connected to the waste engine oil basin.

The oil filter can be changed by yourself, but it is not recommended to do it yourself. Because the oil filter element is not screwed well, it is easy to slip, and the amount of oil is not well controlled, it is easy to add more or less, which will affect the normal operation of the engine. Engine oil is the "blood" of the engine, which plays an important role in the whole working process of the engine, not only to provide sufficient lubrication for the piston cylinder and the internal moving parts of the engine, but also to cool, seal, prevent rust, clean, buffer, etc.

1. First of all, open the oil filler cap and pull out the dipstick. Loosen the oil drain screw on the oil pan and catch the waste oil with a basin, and remove the oil filter by hand while draining the oil. After the standby oil is basically cleaned, unplug the high-voltage line on the distributor cover, start the motor for about 5 seconds, force the remaining oil to be discharged, and then install the high-voltage line and tighten the oil drain screw.

2. Pay attention when installing the oil filter: the new oil filter must be filled with oil, and the sealing rubber ring should also be coated with an appropriate amount of oil to prevent it from being crushed during installation. The oil filter is not tightened as tightly as possible, but it is advisable to use a wrench to twist 1 2 3 4 turns after it cannot be twisted by hand.

3. Fill the engine oil. Generally, an inline 4-cylinder engine with a displacement of liters requires about 4 liters of engine oil, please refer to the vehicle's manual for the specific amount. After the oil is added, start the engine, under normal circumstances, the oil pressure lamp should be extinguished, idle for about 10 minutes, check whether there is leakage in each part, wait a while after the ignition is turned off and then check the oil dipstick, the oil level should be located between the upper and lower limits, if it is insufficient, it should be added in an appropriate amount.

Photo by Q&A) M5 Xpeng P7 AION V Trumpchi GS8 Xpeng P5 Ideal ONE @2019