-
Anonymous users2024-02-13The first thing to do is to find a lift that can lift the car up, there is really no lift to find a trench or a vacant land, prepare an empty basin, drill under the car, unscrew the oil pan screw with a wrench, use the empty basin to receive waste engine oil, pay attention to the hands and feet to be fast, do not splash on the body, it is difficult to wash. The old engine oil is almost finished after about half an hour, and the original car oil pan is screwed on. Then open the engine cover, find the oil port, pour the oil into it from the oil port, and look at the amount of oil poured from the oil ruler.
It's not very difficult to operate.
-
Anonymous users2024-02-12If you simply change the oil, it is relatively simple, tell you the method, use a jack to support the car, if there is an engine guard, first remove the engine guard, screw the oil filler, and then remove the oil drain screw, remove the oil filter element, tighten the oil drain screw, install the new filter element, fill the oil, install the filter element, measure the oil level, take a taxi to see if there is oil leakage, over!
-
Anonymous users2024-02-11It is not difficult to change the engine oil, and the steps are as follows:
1 Raise the car a little and find an oil drain screw under the engine and unscrew it.
2 It is best to use a container to catch the released engine oil, so as not to corrode the ground with the oil, and it is also easy to clean.
3 When the standby oil becomes dripping, tighten the oil drain screw.
4 Add new oil.
-
Anonymous users2024-02-10If you just change the oil, you don't need a lift or a gutter, just buy a pair of car maintenance ramps.
-
Anonymous users2024-02-09If it's a bit like when you can't control it remotely, then go ahead and do it as scheduled.
-
Anonymous users2024-02-081. Start the car engine first, and then extinguish it when the water temperature reaches the normal range. The car can then be lifted using a jack or a car lift.
2. Then open the oil port at the bottom, and use a special wrench to open the oil filter element, you should know that the flow rate of the oil port is very slow, and you can open the filter element for secondary release at this slag time. However, it is important to note that you must wear gloves during this process, after all, the oil and filter cartridge are very hot.
3. After the last wheel, when all the oil is clean, use a wrench to install the new oil filter. Pour the oil that meets the specifications (just the right amount) into the oil pan and you're done, but be sure to aim at that mouth, and use the funnel to fill if you can't do it.
4. Of course, we also have to start the engine to see if the oil volume is normal, which is to check whether there is any leakage in the lower part of the engine.
-
Anonymous users2024-02-071. If you want to change the engine oil by yourself, you must first prepare a waste oil basin and put it under the oil port screw. Then use a special wrench to loosen the oil port screws and let all the old oil flow into the waste oil basin.
2. Unscrew the oil filter and replace it with a brand new one. At this time, it is also necessary to pay attention to cleaning or replacing the oil filter element, because the main function of the oil filter element is to filter the impurities in the oil, if it is not cleaned or replaced, it will lead to the impurities on the oil filter element, flowing into the clean oil, resulting in the oil being polluted, and it will lose the meaning of replacement.
3. Pour brand new oil, you need to pour it in the specified position, and at the same time, you should use the oil dipstick to verify whether the filling amount is in the normal range. Then check for oil leaks and make sure that there is no future to install the guard. Since the oil will have some impact on the environment, the replaced oil needs to be placed in the oil purifier and cannot be thrown away.
-
Anonymous users2024-02-06With the increase in car ownership, most people own a car, but they don't know how to maintain it, YACCO imported lubricants and share with you how to change the oil filter.
Tools Required: Raw materials.
1. One barrel of engine oil, one original machine filter, and one machine filter tool that meet the lubrication standards.
2. A live wrench or a board suitable for the size of the oil bottom screw, an oil basin, and a piece of cotton cloth.
1. Start the vehicle for about 1 minute to make the oil flow fully, and then turn off the engine.
2. Open the oil filling port cap and loosen the filter and oil bottom screws with tools.
3. Place the oil basin under the oil bottom screw, completely loosen the oil bottom screw, and release the old engine oil until it does not flow at all.
4. Tighten the oil bottom screws and wipe off the excess oil stains with a cotton cloth. Unscrew the old filter, it is recommended to put a cotton cloth on the hot hands carefully, apply oil to the sealing ring of the new filter, and tighten it in a clockwise direction.
6. Restart the engine for 1-2 minutes, observe whether there is oil leakage at the oil bottom screw and the filter, and if the oil leaks, the engine should be turned off in time for inspection and treatment; If there is no oil leakage, check the oil quantity of the dipstick after the ignition is turned off, add it to the standard position (the position where the center line of the oil scale is up), and replace it.
-
Anonymous users2024-02-05It is not difficult to change the oil by yourself, but the difficult thing is the site and tools, and with the tools, you can plan to change the oil by yourself.
1. First buy the oil and oil filter suitable for your own model, the sleeve wrench of the oil filter 2, drive the car to the gutter or bracket, unscrew the cover of the oil filling port, unscrew the bottom oil drain screw, prepare a basin in advance to receive waste oil, and it is best to wear a disposable glove when screwing to save a hand of oil.
If you use a pumping unit, you don't need to put it on the shelf, but the car with the machine filter at the bottom must have a trench or bracket.
3. Remove the filter, if it is at the bottom, you can pour some oil into it before installing the new filter4. After the oil is finished, install the oil drain screws back, and pay attention to fastening according to the specified torque value.
5. Add oil according to the specified amount, and check the oil dipstick after the vehicle is off the shelf to see if the oil filling amount is appropriate. Don't dump the waste engine oil, and you can give it to the repair shop after bottling**.
-
Anonymous users2024-02-04Step 1: Turn off the car after driving onto the lift, then use the lift to jack the vehicle, pull up the handbrake and squeeze the front wheels up with a wooden wedge.
Check the drain bolts, reinstall the drain bolts, and be careful not to overtighten the bolts to prevent damage to the oil pan.
Step 3: Move the oil container under the oil filter, use an oil filter wrench to loosen the filter, and then unscrew it by hand. If the filter is still hot, remember to wear gloves.
Even if the filter element was tightened before, there is no need to worry about damaging the filter element during the removal process, as long as it does not damage the connection screws that install the filter element and the parts around the filter element, after all, we no longer use the removed filter element.
Step 4: Refer to the user manual to select the appropriate oil filter.
Step 5: Use new oil to apply the interface gasket of the new filter. If the filter is installed vertically, you can pour some fresh oil into the filter, which will reduce dry grinding the next engine start.
Screw the filter in by hand and tighten the filter as indicated (usually after tightening the filter by hand and then screwing in 3 or 4 turns).
Step 6: Pour the new oil into the oil pan, taking care to refer to the user's manual. A funnel can be used to prevent oil from being poured on the outside of the engine.
Check the lower part of the engine for leaks. If there is no leak, put down the vehicle, check the dipstick, and start the engine, the indicator light on the gauge should turn off immediately after starting. Finally, turn off the engine and double-check the oil level and dispose of the old oil and filters according to local regulations.
-
Anonymous users2024-02-035.How do you change the oil?Why does the 4S shop always say that 5,000 kilometers to change the engine oil?After reading the knowledge.
1.Now put the two iron frames (rhinoceros ramps) under the front wheels, and be sure to use jacks in case of accidents. >>>More
Nowadays, there are many brand stores that deal in loose diamonds on the Internet, most of which can be DIY to choose, according to their budget preferences, choose cost-effective loose diamonds, and choose their favorite rings. But first of all, you have to understand the diamond 4C, compare a few more and then decide to buy, due to different brands, different marketing models, the products sold by each merchant will be different, so don't just care about **ignore the diamond 4C. After understanding the 4C standard, you should also pay attention to some details when choosing diamonds, and also pay attention to whether the diamond has fluorescence, diamonds with fluorescence are cheaper than those without fluorescence, if the diamond has a weak fluorescence, it will not affect the quality, if it is medium or above or strong blue fluorescence, you should consider it carefully. >>>More
The snack box is a bamboo frame found in an old house, and when I found it, it was very dirty because it was full of dust, and I almost threw it away. I thought I might be able to wash it out, so it took me half a day to scrub it out, and I was surprised to think it was super tasty, and I liked it very much. So I used it as a snack box and placed it on the bedside stool.
When bathing the corgi at home, you must buy it a special dog shower gel, and after washing, you must use a special drying box for dogs to dry its hair, otherwise it is easy to catch a cold.
Do more things at home, let your parents feel that they have grown up and have the ability, participate more in some major events in the family, express their opinions more, be assertive, make your family feel that they can rely on you, and the key is to make yourself very strong, very good, and have the ability to take care of your family, protect your family, and become the core force of the family.