Which is better, pure wood or carbon

The ground floor is a bit of a problem.

The second and third floors have already said the difference almost, and add a few:

At present, the arc circle is in power, the vast majority of professional players are using pure wood 5 clips or 7 clips, there have been some woven carbon layer is very close to the surface of the violent board, but because the carbon rigidity is too strong, it is difficult to control and the disadvantage is obvious after retreating. After several years of adjustments, the characteristics of carbon strength have been weakened as much as possible, such as thickening the surface layer to bury the carbon deeper, or giving up the weaving carbon and replacing it with thin carbon, carbon sheets, carbon glue or mixed other fibers, etc., to make it closer to the performance and feel of pure wood.

Professional players are mostly cautious about switching to carbon plates: either taste it at a glance such as Marlene soft carbon, or comprehensive weaving such as Marlon glass carbon mix, and more people use aromatic carbon mixing, etc. Because it's the inorganic era, and the position is getting higher and higher, maybe the original violent board will reappear, but I think the mixed editor may have a better chance of becoming the protagonist.

Each has its own advantages, and it is chosen according to the individual's feel and playing habits.

Usually the pure wood bottom plate has a good feel, good ball holding, strong ability to make arc circles, the pure wooden board of five clips is generally suitable for arc fast play, and the pure wood board of seven clips is suitable for fast arc play, and at the same time, because of the clear feel and relatively strong control, it is recommended for beginners.

The carbon base plate is fast, the ball is fast, and the body is tough at the same time, easy to borrow, and the power is greater in the middle and near Taiwan, which is generally suitable for fast arc play, and the strength and speed are stronger than the pure wood bottom plate, but the control is not as good as the pure wood, and the carbon base plate can be considered with a certain level of technology.

The power is great with pure wood.

If the strength is small, make up for it with carbon.

There is also a pure wood bottom plate that requires higher technical action, and pure wood is used for the most quality treatment in the table.

There is also technology that determines everything, and the pure wood bottom board can also play with high quality.

This one should be chosen according to the individual's feel.

Usually the pure wood bottom plate has a good feel, good ball holding, strong ability to make arc circles, and at the same time, because of the clear feel, the control is relatively strong, in addition, because if it is a thinner pure wood board (such as 5 wood), usually the deformation will be relatively large, and the power of the COSCO platform is strong.

The carbon bottom plate is fast, the ball is fast, and the body is tough at the same time, easy to borrow, the power is greater in the near and middle stage, the strength and speed are stronger than the pure wood bottom plate, and now after the use of inorganic glue in table tennis, I think the carbon plate may become the mainstream in the future.

It depends on the individual, the power of pure wood is relatively large, but the control is relatively weak. The control of carbon is relatively good, but there is a slight gap in strength. The key depends on the individual's style of play. However, the one with glass fiber is also better, and it should be somewhere in between. Relatively balanced.

1. Good carbon fiber.

2. Reasons: (1) The density of the carbon fiber racket is uniform, the force reaction speed in all directions is the same (elasticity), and the movement state of the table tennis ball is completely determined by the way the player hits.

2) The density of solid wood rackets is uneven (annual rings), there are slight differences in the speed of force reaction in all directions (different elasticity), and the movement state of the table tennis ball is not determined by the way the player hits it (there is a certain degree of chance). Even if the density of the composite board is as uniform as possible in all directions, there are still differences.

3. Note: The carbon fiber racket cannot be vibrated violently, resulting in cracks, which will destroy the uniformity of density.

Summary. Table tennis rackets can be divided into two categories according to the classification of materials, pure wood bottom plate and carbon bottom plate.

2. Extended introduction.

1) Single plank, is a whole piece of wood, only single cypress and single ayous two kinds, single plank is very violent, but basically the thickness of the double-sided will exceed the standard, and it is heavier, South Korea and Japan are more famous for their single cypress There are many players, such as Yoo Seungmin.

2) Five clips of pure wood, it is heavier than eating the ball deep, creating an arc circle, to the opponent's table to rotate to cause two jumps to accelerate. Five-clamp pure wood is the most widely used.

3) Seven clips of pure wood, with the characteristics of fast speed and great strength, suitable for fast attack near the platform and retreat from the middle of the platform.

4) Carbon bottom plate, carbon bottom plate is not the whole ball board is carbon, but the carbon layer is added to the wood interlayer, or toner is added to the glue when the wood is bonded. The carbon base plate is very elastic and has more strength than a pure wood base plate with the same structure without carbon. However, the carbon bottom plate has the characteristics of poor feel and weak control, especially when it does not exert force, it is almost the same as when it is forced, it plays very strongly, and the small ball in the table is particularly at a loss, and it is usually used by amateurs to make up for the lack of physical strength.

5) Fiberboard, fiberboard is a combination of the rotation of pure wood board and the speed of carbon board, usually used as a fast speed and strong arc ball play.

Which wooden table tennis racket is good?

Hello! We're happy to answer your questions.

Here are a few of them, I hope you find them helpful.

Table tennis rackets can be divided into two categories according to the classification of materials, pure wood bottom plate and carbon bottom plate. 2. Extended introduction 1) Single plank, that is, a whole piece of wood, only single cypress and single ayous two kinds, single plank is very violent, but basically the thickness of the double-sided will exceed the standard, and it is heavier, South Korea and Japan use single cypress to be more famous There are many golfers, such as Liu Chengmin. 2) Five clips of pure wood, it is heavier than eating the ball deep, creating an arc circle, to the opponent's table to rotate to cause two jumps to accelerate.

Five-clamp pure wood is the most widely used. 3) Seven clips of pure wood, with the characteristics of fast speed and great strength, suitable for fast attack near the platform and retreat from the middle of the platform. 4) Carbon bottom plate, carbon bottom plate is not the whole ball board is carbon, but the carbon layer is added to the wood interlayer, or toner is added to the glue when the wood is bonded.

The carbon base plate is very elastic and has more strength than a pure wood base plate with the same structure without carbon. However, the carbon bottom plate has the characteristics of poor feel and weak control, especially when it does not exert force, it is almost the same as when it is forced, it plays very strongly, and the small ball in the table is particularly at a loss, and it is usually used by amateurs to make up for the lack of physical strength. 5) Fiberboard, fiberboard is a combination of the rotation of pure wood board and the speed of carbon board, usually used as a fast speed and strong arc ball play.