How can you make the meter run slower? How to make the meter run slowly

In fact, the meter is according to the normal speed, if the electricity consumption at home is more, the meter will naturally go faster, and the electricity consumed is also more.

If you want the meter to go slowly, then you usually need to turn off the power in time when using electrical appliances, and the electrical appliances that are not used should also be unplugged, and usually when you go out, you should also turn off all the electrical appliances at home, so that you can also make the meter go slower, and naturally you can save a lot of electricity bills, and some electrical appliances also consume electricity when they are plugged in, but the consumption is relatively small.

You can open the meter housing and loosen the ejector wire above or below the center of the rotating disc a little, while tilting the vertically mounted meter 15 degrees. This will allow the meter to go a little slower.

1.Tilt the vertically mounted meter by 15°

2.Open the meter wiring cover, loosen one of the screws of the current wiring card in the upper left corner of the terminal (horizontal clip), (note that there is electricity, please use an insulated screwdriver to operate), the meter at this time is counted when the electricity load is large, and the load hour is not counted.

3.If you are more professional, you can open the meter shell and loosen the top wire above or below the center of the rotating disk, which works best with the first method.

If you can move the meter, there are several ways to make it slower.

1. Change the voltage of the voltage coil.

2. Change the number of current coils.

3. Change the digital metering gear.

4. Change the gear ratio of the turntable shaft (this trick is the most unique, as long as you can't see the flaws in the table dismantling, it is difficult for experts to find out).

5. Control the internal electricity consumption of the meter (this method can only control the turn and stop of the meter, not fast or slow) 6, other methods.

Use a professional instrument [electric energy meter effectiveness device] to calibrate the meter, so that the electronic meter can be adjusted slowly or faster.

Modify the pulse constant in the metering program.

First of all, if you want to make the meter run slower, then you should use it less. Electrical appliances. As long as you use less, he will naturally spin more slowly, and if you want to make it slower yourself, it must be illegal.

According to your description, this is an act of electricity theft.

Electricity theft is illegal, and no individual or organization may use any means to commit electricity theft.

According to the relevant laws and regulations of our country.

It is stipulated that the power supply enterprises will stop the electricity thieves who are found and can stop the power supply on the spot. The person who steals electricity shall pay the electricity fee according to the amount stolen, and bear the default electricity fee of three times the electricity fee. If the power supply company refuses to bear the responsibility for electricity theft, it will report to the power management department to deal with it in accordance with the law.

If the amount of electricity stolen is relatively large or the circumstances are serious, the power supply enterprise will request the judicial authorities to investigate criminal responsibility in accordance with the law.

We hope you find ours helpful.

As long as the connection piece on the inlet terminal of the live wire is disconnected, but the zero line cannot be disconnected, and the meter will not turn when it is broken; If it is a three-phase watt-hour meter and does not have a transformer, it is enough to disconnect the two-phase jumper meter.

Electronic meters are special measuring instruments, which have strict quality management requirements when they leave the factory, and are subject to random inspection by the quality supervision department. Although there are often people who find ways to find the loopholes of the electronic meter, and want to make it slower and pay less electricity, it turns out that these practices are futile, from the point of view of the electricity consumer, there is no way to take measures, if the meter is disassembled, it will be severely punished, and the result is more than worth the loss.

With less or no electricity, it will not turn or turn slowly.

With the rational use of high-power electrical appliances, the meter will be slower.

Most of the time the meter is "running fast" is not because there is a problem with the meter, but because you have a lot of high-power appliances in your home, sometimes they are on at the same time. For example, in winter, many southern friends will use an electric heater called "Little Sun" to keep warm, and sometimes put one in a room.

It is impossible for you to adjust or change the meter yourself, it is illegal, and you can only save electricity at ordinary times.

Operating Instrument: Electricity Meter.

Here's how to slow down your meter:

1. As long as you cut off some of the coils in the meter, you can slow down the meter.

2. There is a professional instrument energy meter effect test device on a certain treasure, take this to calibrate the meter, so that the electronic meter can be slowed down.

3. After disassembling the meter, add a copper wire on the sampling shunt.

Precautions for using the meter:

1. Many people have installed more electricity meters in their homes, so many electricity meters, pay attention to his pointer when making the crack with the answer, whether there is zero, if it is not explained at zero, you need to adjust the mechanical pointer to the zero position.

2. When using the meter, pay attention to the signs on the meter, such as plus and minus signs, which are the positive and negative poles, and the red and black wires should be inserted into the positive and negative electrodes respectively.

3. When using the meter, if you want to measure the meter, we must use a special test tool, and do not touch the meter with your hands to prevent the current from causing electrocution. <>

There is a screw on the left side of the shell of the table, which is 1cm in diameter, which is used to calibrate the watch, and can be turned clockwise with a flat mouth, it will go slowly, but the slowest can only be less than about one degree of electricity a day, if you want to only go ten kilowatt-hours a month or less, you have to use the second method to steal the beam and change the column, take a 600 rpm meter, that is, turn 600 times to one kilowatt-hour of electricity, the larger the number means that the same electricity will be turned more times, remove the gear combination inside, Change it with the gear combination of your big meter, your big meter must be the kind of 200 rpm, after replacing it, haha, your electricity bill is the original 1 3, rest assured, the parts in the meter are standard parts, it must be worthy of it, but it is to completely remove the meter when doing hands and feet, it is more troublesome, once it is replaced, it is the person from the meter factory who will not find the reason to check, unless he takes the meter back to the tester to measure the number of revolutions, the general electricity bureau does not have this equipment, haha.

The above method is a bit troublesome, the last plan, is to stop the table completely, this method is easier to implement, notice that there is a rectangular cover at the bottom of the table, remove the only screw on the top, there are a few screws on the left inside, two of them are connected with a small horizontal connecting strip, loosen the two screws, dial the connecting strip to the other side, cover the lid, okay, see if the meter is still gone, it is recommended to walk on ten kilowatt-hours of electricity every month and then do this, Otherwise, you can't use 0 kWh of electricity in a month.

Turn off the lights and use less electricity or pull the brake directly.

Install (do not disassemble) the leakage protector to avoid a large amount of leakage. Whether your home's electricity will slip away quietly, a small object is crucial. It is the leakage protector.

Aging wiring in the home, being bitten by small animals or being damaged by other external forces may cause the wire insulation skin to be damaged and leakage. If the weather is humid, the meter will "run fast", and it is all money. The owner of a pig farm once wound wires around the laundry rebar, causing the insulation skin to be damaged and leaking.

He did not install a leakage protector, and lost more than 8,000 yuan in vain in just one month. A properly functioning leakage protector can completely avoid these situations. It can detect the leakage current in the home and automatically cut off the power to stop the meter from "flying".

With the rational use of high-power electrical appliances, the meter will be slower.

I'll come back to you on this question, if you don't use much electricity, it will definitely turn slowly.

Such a solution that affects normal use is generally not feasible. I recommend switching to an electronic meter so that it doesn't turn at all!

Here's how the meter can turn slowly:

If it is daytime, we can set the temperature of the air conditioner to 26, which can save electricity and make the human body more comfortable. Laughter.

Now the outside temperature is about 30 and we turn on the air conditioner at 26. The temperature difference between indoor and outdoor temperatures is not too large, which can also play a role in saving energy.

Here's how to adjust the speed:

The same as the meter has a calibration button, so the speed of the meter can be adjusted, but it will be inaccurate after adjustment, so it is strictly forbidden to adjust the meter privately after calibration.

If you can open the lid of the meter, there are many ways to do it. The energy meter of manual meter calibration only needs to change the meter calibration to make the meter go slower or faster.

The electronic meter can also be opened, but it has to be unpacked, there are adjustable resistors and voltage regulation in it, and the mechanical ones can be unpacked, but they have to be unpacked. The simple way of the machine is to find a strong magnet and put it on the meter.

The screws marked with the plus and minus signs on the left side of the old-fashioned meter glass are adjusted to speed and slow, but the one has a lead seal, which can only be adjusted by opening the glass cover, and the adjustment in the direction of the minus sign is slow.

The reasons for the speed of adjustment are as follows:

The sub-meter itself consumes electricity, each sub-meter consumes about one degree of electricity per month, then the total meter reading will be larger, when there is a situation of electricity theft, the total meter reading will be much larger, and the sub-meter is very little.

The meter measurement is not accurate, and most of the meters installed by the power supply bureau are slightly fast, and the meter has errors. <>