Can the Haval H6 run in the first three gears during the run in period?

Of course not, it needs to be used in every gear to achieve the normal run-in of the gearbox gears.

The break-in period before the first maintenance of a car is generally referred to as the break-in period. There will always be certain subtle defects on the surface of the new transmission parts of the automobile, which makes the joint and meshing between the parts and components not tight enough when they are running, resulting in more intense friction at the contact point. If the speed is too fast, the parts will be permanently damaged due to the high friction temperature of the contact points or the excessive load.

Therefore, in the initial operation of new automobile transmission parts, the relative speed of the contact point should not be too high and the lubrication should be replaced in time, so as to avoid the metal fragmentation suspended in the lubricating oil from entering the friction surface and accelerating the wear of the parts. After a period of operation and friction of the new transmission parts, the contact between the joint and the meshing surface is very consistent, and the surface is very smooth, which is called running-in.

After the run-in period, all parts need to be checked and tightened, and the oil deterioration is also serious, so the vehicle needs to be maintained in time.

Precautions: 1. Do not drive at high speed At the beginning of the new car, you should not run at high speed. The first stage of the run-in period is the first 100 kilometers, which is the most important period!

Try to change gears as much as possible within these 100 kilometers, grind, but don't drive too hard, and drive gently. The second stage is between 100 km and 1000 km, with a maximum speed of no more than 80. The third stage is from 1000 km to 3000 km, the speed does not exceed 80% of the maximum speed, and it is required to pay attention to the engine tachometer and speedometer in use, so that the engine speed and speed are working at medium speed, about 3000 rpm.

3000-5000 kilometers, after the first insurance, you can go to pull the highway, the purpose is to remove carbon deposits in the engine. There are two-wheel drive and four-wheel drive multi-mode cars, in the run-in period are used for use, the speed is gradually accelerated, do not use in the early stage, to the run-in period is almost out of the run-in period, we all know that four-wheel drive is more differential than two-wheel drive, which is also gear, and the run-in method of the gearbox is actually the same. In addition, because the load on the engine and gearbox is different between the four-wheel drive mode and the two-wheel drive mode, it is recommended that the four-wheel drive run-in speed is lower than that of the two-wheel drive, which has a protection for the car as a whole.

Second, do not drive with full load The various parts of the new car are just processed, the run-in period of the new car will produce a lot of debris in the engine, and the shock absorption system of the new car, the transmission system and the brake system are all new parts, and the joint part of each other is not very tight and smooth, and the full load will cause damage to the engine and other components due to excessive load. Therefore, during the run-in period, it cannot exceed 80% of the rated load. The best way to do this is:

During the run-in period, the car should not be full, and try to ensure that only two people are in the car.

That's right. Try to run in the first 3 gears, which is more conducive to the slow run-in of the engine, which is good for the car and you. FYI: Please set to .

It's okay, as long as the engine speed doesn't exceed 3000 rpm, it's fine! 6 gears can run the same!

This is not good for the vehicle, it is recommended that the run-in period choose different gears according to the road conditions, and each gear is run-in.

It is best to use several gears, because it is a run-in, so each gear should be used.

The break-in period means that the engine should be running at 3,000 rpm and should be used in every gear. The gears are also running-in.

The run-in period of the new Haval H6 car refers to the stage when the new car leaves the factory for the first time to drive a certain distance to make the run-in of each component of the module smooth, and the run-in mileage of the new car is generally 1000 km - 3000 km. In addition, the new Haval H6 run-in period. It should be noted that;

1. The development of heating first: this is also for the EFI truck, before the development, the key should be turned to the second gear and wait for 5-10 seconds, restart, which is also because after the key door is opened, the oil pump will start to work, so that the steam pressure and ignition advance angle will be adjusted, therefore, restart after a few seconds to maintain the new car engine;

2. Avoid emergency braking: emergency braking not only damages the brake blind car system in the running-in, but also continues to increase the impact load of the automobile chassis and the diesel engine, and it is best not to have emergency braking within 300 kilometers of the first drive;

3. Prevent the load from being too heavy: if the new car is fully loaded during the run-in period, it will cause damage to the parts, therefore, within 1000 kilometers of the first drive, the domestic car can not exceed 75%-80% of the rated load;

Generally speaking, before the first change of engine oil for the first time of the first warranty of a new car, it can be called the run-in period of the new car, but now the production and manufacturing technology of the vehicle is becoming more and more precise, and the definition of the run-in period is gradually eliminated. For the safe driving style during the run-in period, the general standard is to prevent violent or limited safe driving, for example, it is not necessary to prevent the car engine from constantly spinning at high speeds, and there is also a little attention to let the vehicle gently "warm up" after the cold start in the morning

Millions of car purchase subsidies.

The run-in period of the new Haval H6 car refers to the period when the new car leaves the factory for the first time to run in for a certain distance to make the various parts of the engine run in smoothly, and the run-in mileage of the new car is generally 1000 km - 3000 km. In addition, the run-in period of the new Haval H6 car. It should be noted that;

1. Preheating at the start: This is for the EFI car, before starting, you should turn the key to the second gear and wait for 5-10 seconds before starting, this is because after the key door is opened, the gasoline pump will start to work, so that the oil pressure and fuel injection amount will be adjusted, therefore, start after a few seconds to protect the new car engine;

2. Avoid emergency braking: emergency braking not only makes the braking system in the run-in be impacted, but also increases the impact load of the chassis and engine, and it is best not to brake urgently within 300 kilometers of the initial driving;

3. Avoid overload: If the new car runs at full load during the run-in period, it will cause damage to the parts, therefore, within 1000 kilometers of the initial driving, the domestic car can not exceed 75%-80% of the rated load;

Generally speaking, before the first oil change of the first warranty of a new car, it can be called the run-in period of the new car, but now the manufacturing process of the car is becoming more and more sophisticated, and the concept of the run-in period is gradually fading. As for the driving method during the break-in period, the general rule is to avoid intense or extreme driving, such as not avoiding frequent engine ramps to high revs, and pay a little attention to allowing the car to gently "warm up" after the cold start in the morning

How long is the run-in time of the Haval H6?

The run-in period of the new Haval H6 car is generally within 3000 kilometers after landing, so that you can drive the car to the 4S shop to enjoy the first free maintenance.

The body size of Haval H6 is 4640 1825 1690mm, and the wheelbase is 2680mm, which surpasses the large empty room of SUVs and joint venture sedans of the same level, and will bring customers comfortable, convenient and multi-functional freedom. While creating a spacious and comfortable riding space, Haval H6 pursues a higher level of overall harmony, covering overall luxury, ride comfort, driving convenience, safety, and even economy.

Following the bumper harvest of the Haval H5 word-of-mouth ticket market, Sun Yu Great Wall once again launched the heavyweight product Haval H6. This model has already attracted the attention of the market because it is still in the stage of secrecy, and it has now been confirmed that it will be launched on August 25. Although there is not much difference in body size, the positioning of the Haval H6 is very different from that of the H5.

The H6 can only withstand light off-road with a load-bearing body, two-wheel drive or four-wheel drive, but it is more suitable than the H5 in terms of urban roads.

Millions of car purchase subsidies.

The following points should be paid attention to during the run-in of Haval H6:

1) When driving the vehicle, try to avoid high-speed, long-distance and full-load driving, and try to preheat the engine before driving, so that the internal parts of the engine can be fully lubricated.

2) First of all, the speed of the vehicle and the engine speed should be strictly controlled. During the run-in period, the maximum speed should not exceed 90 km/h, and the engine speed should not exceed 3000 rpm, so as not to cause excessive load on components such as the engine and gearbox. But try not to let the vehicle drive at low speed for a long time, and change gears in time during the run-in process, so that the gearbox can be fully run-in.

3) Try to avoid sudden acceleration and sudden braking during driving, because this operation is easy to have a great impact on the engine, gearbox, braking system, chassis and suspension.

Different from the non-load-bearing body used by the Haval H5 before, the H6 chooses a load-bearing body structure that emphasizes more comfort, and adopts MacPherson + double wishbone front and rear suspension combined with stabilizer bars. MacPherson front suspension has obvious advantages such as simple structure, small mass and space-saving, which is also the suspension structure commonly used in most urban SUVs. A double wishbone rear suspension with stabilizer bars makes the vehicle more stable, and the H6 also adds rear-wheel steering technology.

According to the manufacturer, it can greatly improve the accuracy and stability of the inflated vehicle when turning at high speeds, which is not obvious in actual driving.

The throttle pedal of the diesel H6 feels lighter than that of the gasoline version, and the response when the throttle is stationary is quite sensitive, so as long as you press lightly, the engine speed can easily jump to the turbine when it turns, and the turbo intervention will make the engine start to exert power quickly, but it does not feel as surging as the gasoline turbo. I don't know if it's because of the weight of the H6 by nearly a ton or the difference between diesel and gasoline supercharging. However, the power loss of the diesel version of H6 is quite serious after the number of revolutions exceeds 4000 rpm, which is in line with the principle of diesel engine, so friends who are used to gasoline engines need to adapt, and the gear shift must be below 3700-3800 rpm.

Within 120km h, the power can be said to be okay. After 120 km h, the power is not so abundant at first, and the acceleration starts to drop.

Millions of car purchase subsidies.

The new Haval H6 should not be run in with sudden acceleration or braking. The engine speed should not exceed 3000 rpm, and the high speed should not exceed 120km h, after the engine and gearbox are running-in, the run-in can be completed at 5000km, and the oil can be changed at the first time.

The run-in period of the new Haval H6 car refers to the period when the new car runs a certain distance for the first time after leaving the factory to make all parts of the engine run smoothly. The run-in mileage of new cars is generally 1000-3000 kilometers. In addition, the run-in period of the new Haval H6 car.

Note the intent of nuclear dismantling:1. Warm up before starting:

This is for EFI vehicles. Before starting, turn the key to second gear and wait 5-10 seconds before starting. This is because after the key door is opened, the gasoline pump starts working, adjusting the oil pressure and the amount of fuel injected.

Therefore, it should be started after a few seconds to protect the new engine. 2.Avoid emergency braking:

Emergency braking not only shocks the braking system during break-in, but also increases the shock load on the chassis and engine. It is best not to brake urgently within 300 kilometers of the first drive; 3.Avoid overloading:

If the new car is running at full capacity during the break-in period, it will cause damage to the parts. Therefore, the first time the domestic car travels 1000 kilometers can not exceed 75%-80% of the rated load; Generally speaking, before the first oil change of the first warranty of a new car, it can be called the run-in period of the new car. However, now the manufacturing process of automobiles is becoming more and more sophisticated, and the concept of run-in period is gradually diluted.

As for the driving method during the run-in period, the general rule is to avoid intense or extreme driving, such as not avoiding frequent high engine speeds, and paying a little attention to warming up the car after the cold car starts to hail in the morning.

Millions of car purchase subsidies.