After 6 years of decoration, the wall falls off, is the wall damp or the decoration is not done?

There is a slight seepage of water into the wall, but it does not penetrate into the room, so the wall is white and falls off due to the tide; The outer edge of the wall is insulated or the construction quality of the real stone paint is unqualified, and the wall stone is frosted, so the wall is white and falls off due to the tide; After 6 years of settlement, due to the relative humidity of the air at home, the wall was closed and the white fell off; During the decoration, the wall was not rolled with super glue, and the quality of the application was not up to standard.

After these problems, I don't want to worry about the interior decoration, because the original to the decoration of the house I am responsible for the person in charge can come to help inquire about the sake is very good, this thing does not want to think about this, it is proposed to let the property management look down, after the wall is treated, the wall inside to find a painter master can be quickly repaired, if the problem factors do not carry out maintenance, only repair the interior wall is meaningless, it will not take long to continue to occur the same problem. If the scope of damp peeling of the wall is relatively large, and there is a double layer of mold, it is proposed to remove part of the damp peeling surface layer and carry out the problem of painting again. The first step is to remove the damp parts of the surface; Then change the sandpaper, etc., and polish the surface layer to polish and flatten; The façade clearance should be moderately expanded, with a relative height of more than 50 cm compared to the current damp.

Use a brush or roller brush to carry out uniform brushing 2-3 times with moisture-proof and mildew removal anti-mildew separator, and then brush horizontally, vertically, and horizontally to ensure that the title page liquid is fully brushed and evenly brushed; Each time, start the next brush after it has completely dried. Until the anti-mildew barrier solution is sufficiently dry, tap water mixed with the anti-mildew isolation layer to the mud after the removal of the wall to a batch scraping, scraping to the same level as the unshoveled wall, this layer of key is to remove mildew and supplement a function. Finally, change to waterproof putty paste to repair and level, and continue to apply latex paint to repair the damp and peeling wall.

We must look for the root cause of damp and mildew in the wall, and we must not only care about how to repair the wall, but also look for the cause of damp and mildew before repairing the wall, and then respond to the wall after solving it. If the walls on both sides of the bathroom door are damp and mildew, then the toilet has a large water demand, causing the water to seep into the sand layer below according to the tile gap, overflowing from the threshold stone, and causing the walls on both sides of the bathroom door to be damp and mildew, so that more bathroom water seepage is solved, and then the wall is treatedTherefore, it is very simple to fix the wall, but it will not be long-term to repair the wall without turning on the water resources.

It may be because of the phenomenon of water seepage and leakage in the wall, or the wall is damp, or it may be caused by improper construction at that time.

This is because the decoration is not done well, of course, it is directly related to the dampness of the wall, and it needs to be renovated.

It is due to the dampness of the walls, and if this happens, then it should be redecorated and can last longer.

Damp walls after renovation can easily cause people to be troubled, mainly because it can have a serious impact on indoor air quality and may even cause health problems. In order to solve this problem, we need to first find out the cause of the dampness on the wall, and then take targeted measures to deal with it.

1.Poor indoor ventilation. If there is a lack of circulating fresh air in the room, the walls are prone to moisture accumulation, leading to dampness. Therefore, after the decoration, it is necessary to keep the indoor ventilation as much as possible, and if possible, you can often open the window for ventilation to avoid a humid environment.

2.The wall building materials are unqualified. If the building materials of the wall are not up to standard, such as the surface paint contains excess water, then in the case of poor ventilation, the wall will be damp. At this time, it is generally necessary to replace the building materials to avoid unnecessary trouble.

3.The foundation is unstable. If the foundation is unstable, the groundwater will seep into the wall during the subsidence of the building, resulting in dampness of the wall. In this case, the foundation needs to be repaired or replaced in time to ensure the stability of the foundation of the house.

4.The paint is peeling off. If the paint does not meet the quality standards during the decoration, it is easy to be damaged and fall off. At this time, the paint that has penetrated by moisture should be treated in time and recoated with the paint that has been refreshed.

In short, for the damp situation of the wall, we need to find out the cause first, prescribe the right medicine, and take effective measures to deal with it. After the renovation, ventilation should be carried out in time to ensure the comfort, health and safety of the living environment.

Hello, it's not normal. There are several reasons for the peeling of the wall skin: (1) The base layer is not cleaned clean or improperly handled.

2) The quality of the prepared mortar and raw materials is not good and the use is improper. (3) The deviation of the base layer is large, the one-time plastering is too thick, and the dry shrinkage rate is large. (4) The ash on both sides of the door and window frame is not tight, and the embedded parts of the wall do not meet the requirements, resulting in hollowing and cracks at the door and window frame.

5) After mixing, the mortar is not used up in time, and the parking time is too long.

The wallpaper used for decoration is not easy to fall off, and the situation of falling off does not reflect that the wallpaper is not good, but that it is not pasted well during construction.

Liquid wallpaper is not "paper" to be precise, it is still latex paint. Just use different tools and add different colors, you can roll out different patterns, so that it looks like wallpaper. Liquid wallpaper construction is more expensive than brushing latex paint.

However, it is generally not a separate liquid wallpaper construction, but the base treatment of the wall is undertaken together with the latex paint.

Wallpaper is divided into a variety of materials, try not to use PVC synthetic wallpaper in the family when buying, because the environmental performance of PVC is relative to natural material wood pulp wallpaper, fiber wallpaper. Fabric wallpaper is poor, especially those that smell plastic. Environmental protection is the first condition for choosing wallpaper, and the décor and ** take a back seat.

No. My house has been sticking for half a year, and there is no problem at all.

It has been glued and will not fall off if it is not torn.

It should be noted that the corner line of the wall will sometimes open a little corner, but it does not affect the wallpaper, when sticking the wallpaper, tell the workers to pay attention to the corner line.

Categories: Life >> Home improvement.

Problem description: The shower of my bathroom is on the load-bearing wall, in order to make the layout more reasonable, we changed the shower to the non-load-bearing wall, which led to water seepage outside the wall skin of the non-load-bearing wall, and our waterproofing and plumbing are not problematic. If this is really the case, it can't be changed now, is there any good way to solve it? I also heard that in the first year of the renovation of a new house, it is easier to rewind the wall skin of the state code, is that so?

Analysis: Is it best not to put the bathroom shower on the wall of the non-load-bearing wall, so that the bucket is particularly easy to seep water, is this so?

That's not true. It is okay to install shower heads on load-bearing walls and non-load-bearing walls, but the key is that the waterproofing is not done well.

If this is the case, it can't be changed now, is there any good way to solve it?

It must be waterproof from the new, and a thin layer of foam board must be added to it from the inside, and the height should not be less than 1.5 meters. (The tiles should be changed to "all-porcelain").

That's right, a new house has to go through the "four seasons" to dry out, so a new house is not suitable for decoration within the first year.

Renovating a beautiful and comfortable home can be an exciting experience, but it can be frustrating and irritating when you find that the walls are falling off. Falling off walls can not only ruin the appearance of a house, but it can also cause safety and health issues. That's why timely measures are needed to address this issue.

Here are some ways to solve the problem of wall detachment:

1.Find the root cause of the problem.

The first thing to do is to find out why the wall is falling off, which will help us find a solution. Sometimes the wall peels off due to a lack of binder or too much moisture on the wall, and sometimes it is due to negligence during construction. Once we find out the cause, we can choose how to deal with it.

2.Repaint.

If you find that the decoration process is not in place, resulting in some parts of the wall falling off, you can use paint to repaint. When painting the wall, it is necessary to pay attention to the fact that the wall should be dry and clean, without oil stains, otherwise the adhesion effect will be affected.

3.Repair the walls.

If the paint doesn't solve the problem, then it may be necessary to cut and re-block the detached parts and use adhesive to bond the bricks. If the cracks in the wall are severe, the cracks can be filled or repaired.

4.Redecorate.

In some cases, it may be necessary to redecorate the entire wall to ensure stability and solidity, such as lead walling. Redecorating can take a lot of time and expense, but it's a long-term solution.

In short, different solutions are needed for different situations. If you're not sure how to solve this problem, it's best to contact a professional renovation company or renovation specialist, who will provide a suitable solution based on your problem. Avoid installing valuables and highly sensitive fixtures around the wall before the problem is resolved.

With people's living standards, many people have their own houses, and they will go through a long process from the construction of the house to the decoration. After the house is renovated happily, there will be many problems in the house, among which it is a very common problem to find that the wall is damp after the decoration. So when the house has a resurgence of moisture, how to deal with it in time?

I'll break it down with you.

First of all, we need to know what is the reason for the resurgence of moisture in the walls of the house. In fact, the wall is damp and other problems. This is caused by the cold of the wall, which is commonly known, but it is actually the reason why the wall insulation is not done well.

Whether the wall that is returning to the moisture is an exterior wall or a wall that is related to the outside world. If yes, that's basically the reason. The wall insulation is not done well, it is a problem of building quality, in the north, a very important part of housing construction is the external wall insulation.

In general, measures are taken in the north to carry out thermal insulation treatment, and the main method is to sandwich insulation materials in the wall. Block the conduction of heat by the wall. If the wall insulation is not done well, it will lead to cold penetration, and the phenomenon of cold penetration is mold, blackening, and hair growth on the indoor wall.

The reason is that the indoor air is warm and the water vapor saturation is high, and the wall is not well insulated, so the wall is cold, and the water vapor will crystallize into water droplets on the wall, and the wall will become moldy and hairy when it is wet.

Workaround:

The wall is damp, mainly because the wall insulation should be done well. But sometimes under the current technical conditions in our country, it is impossible to deal with it very, very well, if the indoor humidity is too large, even if the wall insulation meets the requirements. Among them, there are many ways to keep warm, such as:

EPS board, XPS board, thin plastering, exterior wall insulation, polyurethane rigid foam insulation and so on.

In general, the renovated house has a resurgence of moisture on the wall, almost all of which is caused by poor insulation. In fact, at this time, we only need to insulate the wall accordingly to solve this problem.

If you want to deal with the moisture return of the wall, you need to check whether there is any leakage, if there is, you must pry open all the walls for maintenance, and after the repair, you can make up the wall.

In fact, the best way to deal with the phenomenon of dampness is to re-scrape the damp area, so that the wall can be restored very well.

If you find that the wall is damp, the best solution is to contact your property, as it is likely to be related to the overall location.

The cause of peeling and cracking of the wall.

1. Generally, there will be a process of foundation settlement in a new house for one or two years. During the settlement process, the wall stretches, which will cause wall cracks or wall peeling and cracking. In the process of foundation settlement, do not rush to partially repair the wall, it is best to wait for the settlement period of 1-2 years to gradually stabilize before starting to repair the wall.

2. When the developer delivers the house, the wall is smoothed with plain ash, and the workers must shovel off the plain ash of the base layer and re-brush the primer when painting the wall. If the workers do not clean the base layer in the decoration, it will cause the wall to peel and crack for a period of time after brushing the latex paint.

3. Some decoration companies cut corners in order to save money when decorating for the owners, and the ratio of raw materials is unreasonable, for example, too much moisture in the paint.

The walls are peeling. The main reason: less than a year after the decoration, the wall began to peel, the main reason is the poor craftsmanship of the construction workers, putty, paint adhesion and shrinkage performance.

Solution: The worker's process, the layman is completely indistinguishable, first of all, we must choose high-quality products, especially high-quality putty, and we should choose water-resistant putty from well-known enterprises. These putties have high whiteness, good water resistance, high bonding strength, no peeling, no chalking, and no falling off after use, which can solve the trouble of wall skin peeling; Before applying latex paint, you need to scrape the putty at least two or three times; Add 108 glue with gypsum powder to increase the viscosity.

It is recommended that friends paint special use as well. Interior wall latex paint has high requirements for scrubbing resistance, and it is easy to stain the wall in home life, so it can be wiped with water at any time. Exterior paint can be used for interior painting because it also has water resistance, while interior wall paint does not have sun protection and therefore cannot be used to paint exterior walls.

Cracked walls. The main reason: it may be caused by the shrinkage of the putty, the first putty is not dry in the construction, the next putty is scraped, and the second putty is not dried to brush the paint, resulting in cracking of the putty after drying.

Solution: During construction, you should wait for the last putty to dry thoroughly and then scrape the next time, and the thickness of each putty should not exceed 2 mm. When reworking and repairing, the cracks should be scraped clean first, and then scraped with putty, and then painted with topcoat after the putty dried.

The walls are blistered. The main reason: When the wall is blistered, there will be small bubbles in the form of sand grains, which are caused by the following reasons.

1. Add too much pigment or mixed with impurities in the paint mixture;

2. The paint barrel, brush, roller or spray gun is not clean;

3. Before the paint surface is completely dry, moisture seeps into the paint, and the paint film loses its adhesion;

4. The painted wall is not cleaned.

Solution: Avoid painting in the season or weather with high humidity; The time interval of the number of brushing times must wait for the putty or paint film to dry and apply a next layer; Clean up the construction environment before painting and clean up the painted objects.