Why do the floor tiles under the washing machine have a watermark when they are dry?

This is normal: the glaze layer is not worn and the wax of the protective layer is not worn away.

Because the glaze layer on the surface of the newly laid floor tiles is still very good, the cross-section of the bricks is very smooth. After mopping the floor, the remaining water stains will naturally gather into balls, which are called water droplets. The watermark after drying is because the water contains stains when mopping the floor, and the stains remain after the water evaporates.

Don't worry. Rub it with a dry rag and you're good to go.

First, the reason why the floor tiles are not clean and have watermarks.

Although I have been mopping the floor carefully, after mopping the floor, there will always be an unsightly watermark on the floor tiles, and the reasons why the mopping is not clean and the watermark is left are mainly the following two points:

1. Mop tool.

If the mop is not wrung out, it will leave water stains on the floor tiles, and when it dries thoroughly, a watermark will be formed. So here are two suggestions:

When mopping the floor, you can try to wring out the mop a little, or wipe the floor with a dry rag after mopping, then the floor will not leave a watermark;

If the mop is wrung out and then mopped the floor, and the watermark is still left, then it is recommended to replace the mop tool, or check whether it is a floor tile problem.

2. Floor tile problem.

If the floor tiles are dragged and wiped, or they cannot be wiped clean, they will leave watermarks, then the quality of the floor tiles should be considered. Some floor tiles are too poor in quality and have too high absorption rate, so the sewage during mopping will penetrate the surface and form a watermark.

In this case, it is recommended to choose a full-body glazed brick, because its surface contains a glaze after high temperature, and sewage cannot penetrate.

Second, the floor tiles are not clean, there is an old watermark, how to mop the floor?

If you want to mop the floor tiles clean, there are actually three steps, and each step must be in place, so that the floor tiles will be clean and leave no water stains, the specific steps are as follows:

1. Step 1: Sweep the floor.

Sweep the floor before mopping, everyone knows. But be sure to sweep it clean, and if you sweep it a little carefully, you will find that you can sweep away a lot of dust. If you mop the floor without sweeping it, it will also leave a watermark.

2. The second step: feeding.

In the mopping water, you can add some materials, such as adding some laundry detergent, salt or baking soda to the water, which can better remove oil and stains, and it will also dry quickly, so that the floor will not leave an unsightly watermark;

3. Step 3: Wipe the floor.

If you have time, you can wipe the floor with a light-colored rag, and it should be noted that the rag must be squeezed clean before mopping the floor. The floor cleaned in this way is clean and bright.

Note: When mopping the floor, there are two tricks, the first tip is to add salt to 40 -50 warm water, which can use temperature and salt to accelerate the evaporation of the floor; The second tip is to add baking soda and white vinegar to the water, which can easily mop the oil, mop the floor effortlessly, and can also disinfect and sterilize.

Summary: There are two reasons why the floor tile mop is not clean and has a watermark: improper use of the mop tool and the quality of the floor tile. At the same time, you also need to follow the correct steps to mop the floor, so that the mopping and washing of the floor tiles will not leave a watermark.

There is no way to dispose of this, this is a seepage brick, that is to say, the quality of the floor tile itself, there is no way to deal with it, it can only slowly fade after the water evaporates over time. Floor tiles that are too dark can easily leave watermarks. If you want to wipe the floor very clean, you must have a cotton mop with good water absorption Now there is the kind of mop that can take off the mop head so that it will be much cleaner Before mopping the floor, use a vacuum cleaner to suck the ground So that most of the dust and wool debris will be sucked away Then the first mop should be cleaned and screwed until it will not drip I am generally mopping 2 times will be clean The second mop must be washed clean to mop If the first mop is wet and has more moisture, then the second time must be wrung very dry and dry And you can't wait until the first mop is dry to mop again Otherwise, it will be difficult to mop the watermark clean, and the color of the floor tiles is too dark, and it is easy to leave a watermark.

If you want to wipe the floor very clean, you must have a cotton mop with good water absorption Now there is the kind of mop that can take off the mop head so that it will be much cleaner Before mopping the floor, use a vacuum cleaner to suck the ground So that most of the dust and wool debris will be sucked away Then the first mop should be cleaned and screwed until it will not drip I am generally mopping 2 times will be clean The second mop must be washed clean to mop If the first mop is than.

The floor tiles of my house also have a layer of oil-like brightness, recently placed the humidifier for half a month, a piece of floor tiles of the oil is gone, the surface of the hand touch and other bricks are no different, but the rag on the wipe can not be wiped, I feel that there are oil stains on the ground. I don't know what to do.

Which is the protective wax on the brick can be scrubbed with double flyer powder.

You need to prepare: a basin of rice washing water, fabric softener, table salt, and a mop.

1. First prepare a basin of rice washing water for later use.

2. Then add an appropriate amount of fabric softener to the rice washing water.

3. Then add an appropriate amount of salt to the rice washing water.

4. Then pour the rice washing water into the shabu-shabu bucket of the mop for use.

5. Brush the mop in the shabu bucket below.

6. Next, wipe the ground with a mop.

7. Finally, the tile floor will be very clean after wiping, and there will be no watermark.

In fact, flooding after mopping the tile floor is also a common problem, I personally recommend wringing out the mop and then mopping or using a cotton mop, so the water absorption effect is also very good. Another solution is to wipe it with a wet mop first, and then with a dry mop, so that there is no watermark on the surface of the floor tile.

There are generally the following reasons for the watermark after the tile floor is mopped.

First, the mop itself carries too much water. It is recommended to wring out the mop, or use a cotton mop, which absorbs water better.

Second, the surface of the tile has a good protective layer, which is repulsive to water.

Its practical mop mop must have a watermark, it is nothing more than a question of how much and whether it is obvious or not. If you want to solve it, you can use a mop tray first, and then wipe it with a dry mop cloth. Or you can scrape the ground with a glass scraper and there will be no watermark, but it requires a certain amount of skill and is too tiring.

Is there too much water in the mop? You can use dry, in the rub again.

That's the floor, I didn't choose it well, I just had to wait for it to dry slowly.

Mop shabu-shabu, don't bring so much water.

Washing powder. Bubble imprints are water-based stains with weak adhesion and can be removed as follows:

If it is a glazed floor tile such as antique bricks, glazed bricks, and glazed tiles.

Stains generally do not penetrate under the glaze, and can be scraped off with a knife directly after they are dry, and then wiped dry the marks with a damp rag; If it is more laborious, you can soak the surface of the imprint with hot water for a while, and it should be easy to wipe off;

If it is a polished brick, vitrified brick, or a product with no glaze on the surface such as stoneware or ceramic brick, or a product with a relatively high water absorption, it is necessary to soak the imprint with alcohol or hot water for a period of time, and then rinse it with water after the imprint has dissolved, and wipe it with a rag during the period, and the imprint will disappear after a period of time.

84 sanitizer is not recommended.

or corrosive liquids such as banana water, which may not only burn.

The surface of the tile will also change the surface color, which will also have a certain impact on health.

1. Daily cleaning of floor tiles can be cleaned with detergent, soap, etc.

2. Use soap and a little ammonia and turpentine to clean the floor tiles to make the tiles more shiny.

3. The polished tile should be waxed regularly, and the time interval should be 2-3 months.

4. If there are scratches on the brick surface, you can apply toothpaste to the scratches, and wipe them with a dry cloth to repair them.

5. There are some watermarks on the ground after wiping, and you can use a sponge mop to drag it again. And it's very clean.

If it is not a problem with the quality of the floor, then the reason for such a problem may be:

1. The color of the floor is too dark, and it is easy to show watermarks.

2. The mop is not absorbent well.

3. The mop is not wrung out to a certain extent.

4. The mop is not washed clean, and it is easy to have watermarks on light-colored floors.

Solution: If you want to wipe the floor very clean, you must have a cotton mop with good water absorption, and now there is the kind that can remove the mop head, so that it will be much cleaner.

Use a vacuum cleaner to suck the ground before mopping, so that most of the dust and hairy debris will be sucked away, and then the first mop should be cleaned and screwed until it will not drip, generally the second mop will be clean, and the second mop must be washed clean to mop.

If the first mop is wet and has a lot of moisture, then the second time must be wrung very dry, and you can't wait until the first mop is dry before mopping, otherwise it will be difficult to mop the watermark.

There are some watermarks on the ground after wiping, and you can use a sponge mop to drag it again. And it's very clean.

The watermark is not wiped off when the water enters from the brick joint to the back of the floor tile, and the watermark can only be erased after it is completely dry, and the brick joint can be treated to avoid the watermark.

Change the handle, change to a stronger absorbent.

If it is not the quality of the floor, then there is such a problem 1 The color of the floor is too dark, and it is easy to show the watermark 2 The mop is not absorbent 3 The mop is not wrung out to a certain extent 4 The mop is not washed clean, and it is easy to have a watermark on the light-colored floor.

Not force. It's very hard haha.

There are two possibilities for a watermark on the floor tiles:

First: the water content of the base layer of the kitchen and balcony is too high, and there is water seeping into the base layer from the brick joints, which causes the base to return to the water.

Second: the quality of the floor tiles used in the kitchen and balcony. The high water absorption of ceramic tiles makes it possible to have a watermark immediately when there is water.

Another: The kitchen generally does not need to be waterproof, only dozens of centimeters of waterproof next to the floor drain.

White cement and black cement are used as brick joints, and one color of cement is selected according to the depth or lightness of the tile.

For the problem of hollowing the cement floor, it may be caused by the lack of clean cleaning of the base layer and the lack of watering before construction. It's a matter of construction process. If the house is still under warranty, ask the property to repair it for you (you may have to remove it all and rebuild it).

If it is because the quality of the tiles you bought is not good.

There is an important indicator of ceramic tile is the water absorption rate, the water absorption rate is too high in the use of the brick will appear in your home, and now you have to buy a way.

The next time you buy tiles, remember to take a bottle of water and pour a little bit on the back of the tile (that is, the unglazed side).

It means that the floor tiles in your house are not well bought, and they will seep water.

Tile leakage can be solved by doing surface protection.

Old housekeeper cleaning company.

The freshly laid floor tiles, white, with a watermark on them, can't be erased, will they fall off after a long time? Just not the floor tile, it has a layer of anti-fouling treatment on it, like this kind of water quality, when it dries, there will also be a watermark on it.

Watermark removal is more complicated, you need to remove all the protective film on the surface of the floor with a watermark, and then make a new protective film for the whole piece, which is a professional technique, some are to remove this watermark and then make up this piece, but it is not very good, or it can be seen.

It's hard to get rid of it, because the watermark has all penetrated into the brick and become a brick. I also have it in my house, just because I buy bricks of poor quality. Like the self-cleaning function of a slightly better quality surface, if something is wiped on it, it will be gone.

There is no way around this, it should belong to the quality of the bricks!! Poor waterproofing.

Rub with a damp towel dipped in toilet soap or dish soap.

Are you sure it's a watermark? If it is a penetrating stain, we have a special cleaner to solve it.

Old housekeeper cleaning company.

You get what you want, I have to admit the fact that the quality of the bricks I bought is not very good, just like that, it is difficult to get, I suggest that you do not waste too much energy on this and ignore it.

There is no way to get rid of the bricks of poor quality.