Is it better to paste the wall tiles with cement or use tile glue?

It's better to glue with tiles.

One: cement. Cement is our common basic building material, because the mechanical occlusion force generated by cement and other materials after drying and solidifying can fix objects, so cement is often used to build walls, tiles, etc.

Disadvantages: the thickness of the paving is large, the paste is not firm, the use of materials is more and easy to hollow, and the thermal expansion and contraction of ceramic tiles and cement will occur after a few years of delivery.

Two: tile adhesive.

The main advantage of tile adhesive is that the tile paste ability is strong, and it can be waterproof and moisture-proof, not easy to age, often used for exterior wall decoration, and the construction is simple, no need to soak the brick in advance, when using tile adhesive paste, only a thin layer can be needed, and it can also save the space used for coating cement.

Disadvantages: Compared with the cost of cement, the cost of tile glue will be much higher; The market level of tile adhesive is uneven, it is difficult to distinguish the true from the fake, and the inferior tile adhesive will also release harmful gases to endanger human health, and the environmental protection is relatively poor.

3. Specifically.

1. Construction.

Cement tiles are more complicated to construct, and some steps such as wet walls, soaked bricks, and support are required. Not only will the construction efficiency be very low, but the effect of sticking out is not very good (it is easy to appear hollow, falling off and other phenomena). Tile adhesive can directly omit complex steps, and it is more practical.

2. Material adhesion.

Now the quality of ceramic tiles is getting better and better, so even if it is a wall tile, the water absorption is not so high, so the water absorption principle of traditional cement mortar can not meet the current paving, and the tile is getting bigger and bigger, and the tile adhesive is easier to paste. Moreover, tile adhesive is not affected by climate and humidity, and cement mortar is likely to cause the tile to fall off due to thermal expansion and contraction.

3. Aesthetics.

The ratio of tile adhesive materials is more reasonable, uniform, and the shrinkage is more consistent when pasting, so the tiles posted in this way will look more flat, and it is a method of full slurry lamination, so there will be no hollowing and falling off.

If it is an ordinary tile, you can use cement sand, and if it is an all-porcelain one, you should use some glue appropriately.

It is best to choose tile adhesive for tile adhesive, which has good water locking, less structural stress, and better tile structure; Hydroplaning mud is often used in the basic material of construction, because it is thicker than other building materials, so that the letter is very stable and solid, so it is often used to build walls and bricks, etc., but if the cement is coated with a thin layer when tiling,

Is it better to use cement or tile glue for tiling? The traditional way of tiling tiles is to use cement mortar, relatively speaking, this technology is relatively mature, and the cost is low. The adhesion of cement tiles is very high, and the environmental protection is also stronger!

However, there may be some problems with the traditional process, such as it tests the skill of the bricklayer, if the cement is not evenly smeared, the back of the tile will be hollow, easy to fall off. Secondly, cement mortar is used on walls and floors. Nowadays, many tiles are getting bigger and thicker, and sometimes cement mortar alone cannot put new tiles on the wall.

The main component of tile adhesive is still cement, but compared with the traditional cement mortar, its thickness is only about 3 mm, and the viscosity is stronger than that of cement mortar! Some vitrified bricks and glazed bricks that cannot be glued to the wall with cement mortar are acceptable. In addition, the construction of tile adhesive is simple, and there is no need to soak bricks in advance, which is much more convenient for the construction master and the efficiency can be further improved.

1. Hydropower precautions.

1. Waterproof construction should be waterproofed by coating film.

2. The waterproof project should be done after the acceptance of the concealed project.

3. After the waterproofing is done, 2 water storage tests should be done.

4. The waterproof layer of the bathroom should not be lower than the meter.

5. Floor drains, pipelines and other places should be waterproofed more than once.

6. The floor drain should be deodorized.

7. The hot and cold water pipes are hot on the left and cold on the right.

8. Try not to walk on the ground from the water pipe.

9. The cold water pipe should have a protective layer of 1cm, and the hot water pipe should have a protective layer.

10. The bucket should be bought large.

11. The faucet and basin should be matched.

12. Silicone should be used for toilet installation.

13. After the toilet and faucet are installed, they should be taken care of.

14. When buying a toilet, consider the pit distance of the toilet.

15. The washing machine should consider whether it is an upper drain or a lower drain.

16. Don't install ** in the bathroom.

17. The size of the mirror in the bathroom should be considered.

18. Bathroom pipes should be left with manholes.

19. Strong and weak electricity cannot be worn in the same tube.

20. The left zero and right phases are grounded.

21. The power socket is 300mm from the ground, and the switch is meters.

22. Do not install the switch behind the door.

23. There are many sockets.

24. The cassette should be used well.

25. The cassette must be matched with the panel.

26. The air conditioner in the bedroom should not be facing the bed.

27. The air-conditioning hole should be tilted outward.

28. Try to consider dual control of the lamp.

29. It is best to install a splash-proof socket in the bathroom.

30. Consider a socket on the table.

31. The wire duct should be horizontal and vertical, and the photo should be arranged.

32. The public flue should be equipped with a check valve.

2. Precautions for masonry.

1. The cement cannot be used for more than three months after the factory period.

2. Different varieties and grades of cement cannot be mixed.

3. Yellow sand must be made of river sand.

4. The wall and floor tiles should be soaked in water for more than 2 hours, and they can be pasted after drying.

5. It is better to buy a few more wall and floor tiles, not less.

6. There can be no two rows of non-whole bricks on one wall.

7. Clean the tiles immediately after the joint is completed.

8. The ground is pasted with marble, and the back of the stone should be waterproof.

9. The sunny angle should be cut at a 45-degree angle.

10. The floor tiles should be inclined to the floor drain to avoid water accumulation.

11. The ground marble should be dry-paved.

12. The floor tiles must be dirt-resistant and non-slip.

13. Matte tiles are difficult to clean.

14. Pay attention to the drainage direction of balcony floor tiles.

The thickness of the cement mortar will vary greatly from the traditional paving method (thick paste method). The material requires different paving when using tile binder, directly mixed with water can be used, no longer need on-site ratio of cement mortar, the quality standard is easy to grasp, the bonding strength is relatively high, the construction efficiency is also greatly improved, the cement mortar needs to be mixed with water and sand, so whether the cement ratio is reasonable, whether the amount of material is in place, whether the mixing is uniform will affect the quality of cement mortar. Due to the simple operation, professionally trained workers can use ready-mixed tile binder for paving, which greatly improves the efficiency and makes faster progress during paving.

Skilled skilled workers are needed to pave, if the paving process is not in place, it is easy to cause problems such as tile hollowing, cracking, etc., and it is difficult for the paving workers who are not in place to pave the tiles smoothly. In addition to the same need for base treatment and brushing of the wall, the flatness of the wall is required to be higher, and the wall is generally required to be leveled, but the glazed brick is not required to be soaked in water. If the tile is soaked in water, it must be dried in the shade, and the back of the brick is clean and pollution-free.

It is necessary to carry out base treatment and brushing of the wall, and the paving can be carried out after the treatment; Glazed tiles need to be soaked in water. Effect comparison The expected effect of using tile adhesive and cement mortar is as follows: thin wall, reduced hollow drum rate, fast tiling speed and long service life.

Tile adhesive: the tile does not need to be soaked in water, the wall does not need to be wet, and the tile and the wall can be firmly pasted together; The thin paste method is adopted, the thickness only needs 3-5mm, and in the case of the base leveling, it can usually be paved 20 square meters a day.

Tile adhesive: Tile adhesive is relatively simple, as long as you add water and stir, you can use it, saving a lot of processes.

Tile adhesive for wall tiles has a better effect and higher efficiency.

Hope it can help you, thank you.