Do you still need to brush the adhesive on the bathroom wall to do waterproofing? What do you think?

In the case of house renovation, after the water and electricity change in front of the house is completedThe first indoor space of the following interior decoration is the toilet, because of the large water demand, the toilet is in a wet and cold situation every day, and it is also an area with more applications, so it is very important to make waterproof materials. The walls and pavement that have been renovated by the water improvement circuit will be uneven, and things like this cannot be done to prevent moisture.

Apply floor leveling cement mortar.

Carry out ground leveling of walls and pavement, condense and dry, clean the dust and tidy, and then make waterproof materials. According to the walls and pavement solved by ground leveling, the toilet must be made of waterproof materials three times and waterproof coatings.

Stronger maintenance of the restroom, preventing hardcover rooms.

Later, water leakage and other conditions occur, do many waterproof material connection points, the interface around the wall foot, the odor-proof floor drain drainage outlet, continue to brush the waterproof material several times, and the wall is more than three meters high as moisture-proof.

In the case of bathing, the water is not easy to seep into the opposite side of the wall, after the three moisture-proof are done, the irrigation test is carried out, and there is no leakage under the floor, and the moisture-proof is up to standard. Our goal in wall painting is to complete the closed type of porosity on the wall, so that the moisture-proof surface of the wall painting is very smooth. Such a smooth surface layer is especially not conducive to adherence to floor tiles.

, jeopardizing the actual effect of the bonding of wall tiles. In addition to the back problem of low water absorption and high density, we can also deal with the problem of the back of the general floor tile.

to improve the adhesion between the back of the general floor tile and the adhesive raw material. Since the back of the general floor tile is also very smooth, it is also very reasonable to use back dispensing to improve the bond in the middle. In short, the flexible waterproof raw material is a mixed substance of mixed mortar and super glue, that is, a mixed mortar with a certain moisture-proof effect developed by adding an appropriate amount of additives to concrete and gravel.

Normally, moisture protection is only applied to the walls and the bottom layer of the pavement.

The bathroom wall should be waterproofed and brushed with adhesive, and the roles and functions of the two do not conflict, and they need to be done.

Be sure to brush the adhesive, because after waterproofing, if you don't brush the adhesive and stick the tile, the tile is easy to fall off.

There is no need to do it, and even if you do, the adhesive dries quickly and does not work.

It's not necessary, and even if you do, the adhesive will dry out quickly and won't do anything.

If you don't brush it, then the wall is easy to fall off if the stickiness is not good, which will be very dangerous, so it must be very strong.

Be sure to brush it, otherwise the walls will fall off due to the increasing penetration of water vapor. For waterproof walls, special spraying materials or brushed materials are generally used to pull out granular spots on the wall to enhance the combination of adhesive materials and waterproof surfaces.

The full name of the adhesive is called tile back glue, which can solve the problem of low porosity on the back of the tile and increase the adhesion of the back of the tile, so if you want to prevent the tile from falling off, the adhesive must be brushed; The specific method is to first rinse the back of the tile with clean water. If there is a release agent on the back, it also needs to be sanded, and it should be rinsed with water after sanding. , brush back glue.

It should be painted tightly, painted full, and not omitted. Dry.

Must, the wall of the bathroom is waterproof, which means that in the decoration specification, it is required that the corresponding area of the bathroom wall must be painted with waterproof coating.

It should be decided by considering the problems that will affect the waterproofing of the wall. First of all, the surface smoothness should be high, and then the interval on the surface of the cement mortar layer should disappear.