How to make your own distilled water when maintaining the battery

How to make your own distilled water in the maintenance of the battery, distilled water is often an indispensable substance, and it can not be replaced by ordinary tap water, mineral water, pure water, and because many people do not know or have no place to buy, back here, I am here to introduce to you a simple way to make distilled water: tool material preparation: ( Induction cooker, gas stove, electric stove, etc. (induction cooker is preferred, it is best not to use a coal stove, because it has dust) ( A stainless steel pot (with a lid, the larger the pot body, The faster the production speed, a stainless steel basin (used to hold distilled water), a brush (lacquer brush).

Steps: Wash both items in ( ) with tap water once or twice, and should be cleaned fairly clean, so as not to have impurities (solid impurities) that affect the purity. Fill the stainless steel pot with half a pot of water, cover it, and put it on the induction cooker to heat it (the heat is a little bigger, the speed is faster) until it boils, but don't turn off the power You open the lid, you will find that there are a lot of small water droplets on the lid, that is distilled water, but these can't be used, because they are washed with tap water, there are still many impurities (ionic impurities) on it, put these water into the basin, because the amount is relatively small, so you can brush them into the basin with a brush every time, and then cover them back after you are done After a minute or so, after removing the lid, use a brush to brush those small droplets into the basin, cover them back again, and after a minute, open them again.

After a few times, you'll notice that you've gotten a little bit done. But as mentioned above, these cannot be used, and these are used to clean the basin and brush with distilled water, and the amount of water should be enough to clean the basin, and after washing, it should be discarded. Then repeat the above steps, after a few times, the impurities will be less and less, if the requirements are not very high, the water after three times can be used as distilled water, if you think it is a little higher, you can clean it a few more times.

After that, the water is available. In this way, the distilled water we want is ready. A few additions:

1. Stainless steel pots and stainless steel basins are best newly purchased 2, heating process, after the water is boiled, the temperature should not be too high, it should be adjusted a little smaller, slightly open.

The water that is cooled by the hot steam is distilled water. It's the same device as the rural wine, you know, the water is often changed on it. ]

You can buy ready-made purified water from large companies, and I have tested the ionization with only two or three values, which can be substituted for battery distilled water. ]

<>1. First, use a flathead screwdriver to pry open the guard plate of the battery, and then unscrew the six plastic covers on the battery.

2. Then use the suction dropper to directly fill the distilled water until the liquid level is in the middle of the upper and lower scale marks, of course, it is not a problem to fill it up.

3. However, it should be noted that the battery cannot be charged immediately after adding water (distilled water), and it needs to be stationary for 1-2 hours before it can be charged. Because after adding water, it needs to be completely fused with the original battery liquid (dilute sulfuric acid), so as to ensure the quality of battery charging.

Theoretically, when the battery is short of water, it is only allowed to fill distilled water or purified water. Because the battery has been adjusted to the corresponding specific gravity after leaving the factory, if you add electrolyte (stock solution) by yourself, it will naturally cause the specific gravity value to rise.

Summary. Hello dear, I'm glad to answer such a question for you, it's best to add battery refill, open the outer cover of the electric vehicle battery, add refiller to each single compartment, add 5 10 ml to each single compartment of 10-14ah, add 10 15 ml to each single compartment of 17 24ah, stand still for 1 2 hours after adding, observe the inside of the liquid filling hole with a flashlight, wet and whirring just right, if you see the liquid, that is.

If you add more, you should use a needle to suck out some, find a needle, install an infusion tube on the top, insert it into the filling hole, suck the liquid upward, and suck the liquid until the upper part of the plate cannot see the liquid.

Hope mine can help you, thanks.

What should I do if there are more batteries and distilled water.

Hello I am Mao Mao teacher, graduated from East China Normal University, in the question of 1v1 cumulative service of 10,000 people, you can continue to pay attention to me if you don't understand the problem, follow-up for you to answer, typing takes a little time, please be patient and wait, about 3 minutes back to fight the code is silver jujube you

Hello dear, I'm glad to answer such a question for you, it's best to add battery refill, open the outer cover of the battery of the electric potato bright car, add refiller to each single grid, add 5 10 ml to each single grid of 10-14ah, add 10 15 ml to each single grid of 17 24ah, stand still for 1 2 hours after adding, observe the inside of the liquid filling hole with a flashlight, wet and whirring just right, if you see the liquid, that is. If you add more, you should use a needle to suck out some, find a needle, install an infusion tube on the top, insert it into the filling hole, suck the liquid upward, and suck the liquid until the upper part of the plate cannot see the liquid. I hope my reply can help you, thank you.

If it is a maintainable battery, you can add distilled water, add it to the scale mark, and you can't add more. Because ordinary lead-acid batteries in the summer when there is a lack of electrolyte, you can add some distilled water, you can also add battery replenishment liquid. If it is a maintenance-free battery, it does not need to be added.

Distilled water can be added if there is no leakage liquid and the liquid level of the battery is low under normal use, but this distilled water must be distilled water for the battery, not other distilled water, because the distilled water used for the battery still has sulfuric acid in it, but the concentration of the electrolyte added to the new battery is much lower.

Take off the battery first, solder the connecting wire, and wipe it clean with a rag, the next thing is to open the cover, each battery has an exhaust hole, the general battery exhaust hole is on the side of the upper cover, see that there is a gap, that is, the exhaust use, put the slotted screwdriver at the notch, pat the screwdriver with your hand, make the screwdriver head enter the exhaust hole, and then warp it up, and then shoot it inside (the small battery shoots to the middle of the upper cover, because the opening inside is on both sides of the exhaust hole, but the electric motorcycle battery needs to be measured, Because the opening inside is in the middle, so that the rubber cap inside will not be damaged), warp again, do it a few more times, and the battery cover can be warped down, don't be too savage.

After opening the lid, you will find that there are 6 hats, but at this time, you may "jump" twice and fly off a few rubber caps, so don't take off the lid when you open the lid, remove it slowly, and cover it with your hands to prevent the rubber cap from flying off, because maybe the internal pressure of the battery is high at this time. Carefully remove the rubber cap, the white one is absorbent cotton, and it is okay not to remove it.

Next, you can replenish the water, add 7ml to each well (add 12ml to the electric motorcycle battery), (you can also remember that it is not an electrolyte if you buy a bottle of distilled water in the supermarket without replenishing the liquid) in order, you will not be mistaken.

After adding water, you can cover the rubber cap, and the absorbent cotton should also be restored as it is, and you can cover it after it is done, but wait, look at the next step.

After adding water, you can cover the rubber cap, and the absorbent cotton should also be restored as it is, and you can cover it after it is done, but wait, look at the next step.

Use a small screwdriver to dip some PVC glue, a few times on the cover and the battery, and then you can cover it, not too much glue, so as not to be difficult to open next time, and too much may flow to the rubber cap, so that the rubber cap is sealed, which is originally exhaust but can not be vented.

It is best to stay still for 24 hours after the water is added, if you are really in a hurry to use the car the next morning, you can also charge it immediately, if you are not in a hurry to use the car, then wait for a night to charge again, so that the water can be better absorbed, and the electrolyte concentration in each position inside the battery is consistent.

The battery is under warranty, or the battery can automatically turn green when charging, and it is not recommended to add water.

First of all, we have to distinguish between hydroelectric batteries and dry batteries, the specific gravity of the electrolyte of hydroelectric cylinders is, if the water level reaches the inner underline, add the distillation capacity.

Water is OK, if it is a dry battery, which is now a common maintenance-free battery for electric vehicles, its specific gravity is, in the power has not decreased significantly, and it has been used for more than a year (over the warranty), you can add the electrolyte, add it to the wet and wet on it, don't add distilled water, because the specific gravity of the water bottle is different, if you add distilled water power drop not far, I have been fooled. If you have the energy, you can buy a Dafeng brand positive and negative pulse punching appliance to devulcanize the battery, my battery has been used for almost four years, and it has been maintained like this, and the power is still strong.

The first step is to remove the battery from the car.

Copy it up and tear it down. This attack.

When you pay attention to the positive and negative bai pole plus water du after the installation is not confused, the second step, look at the battery liquid, is dao is not below the lowest line, if it is, quickly add water, sometimes because water has never been added, there is not even any water in the battery, of course such a battery can not be ignited!

The third step is to take off the horizontal bar on the battery, it may be a little tight, don't worry, force. Use a syringe or pen barrel to draw distilled or purified water and inject them into the holes. Pay attention to observe the water level when filling the water, and do not go higher than the water line.

Finally, after the water level is in place, put the battery back in its place and start the car to be charged.

Hydroelectric cylinder plus distilled water: must not exceed the horizontal line?

No, you cannot. What the battery needs is distilled water, that is, 100% water, without any impurities, which has no effect on the electrolyte in the battery, and if there are impurities or ions, it will disturb the use of the electrolyte.

The working principle of the battery: when charging, the external electrical energy is used to regenerate the internal active substance, the electrical energy is stored as chemical energy, and the chemical energy is converted into electrical energy output again when it needs to be discharged, such as mobile phone batteries commonly used in life.

There are many types of dry batteries, the common ones are alkaline dry batteries, zinc-manganese dry batteries, and chemical batteries that use a paste-like electrolyte to generate direct current. Dry batteries are small and lightweight, and are commonly used with remote controls, toys, flashlights, etc. Dry batteries are also known as disposable batteries, so there is no way to restore the capacity of dry batteries by adding distilled water after they run out of energy.

The paste electrolyte inside the dry battery has strong corrosiveness and greater toxicity, and it is easy to cause poisoning and ulceration if accidentally taken or stained. Therefore, destroying the battery shell and adding distilled water can easily cause the leakage of the electrolyte inside, causing danger.

Dry batteries contain toxic substances such as mercury, cadmium, lead, zinc, etc. If the shell is damaged, adding distilled water to it will not only not restore the electricity, but also cause pollution to the environment and damage human health. If people are poisoned by mercury, it will damage the central nervous system, and the main harm of cadmium is kidney toxicity, and it will also continue to cause "pain disease" and is also a carcinogen; Consumption of foods containing lead affects enzymes and normal heme synthesis, affecting the nervous system.

Due to the various characteristics of dry batteries, dry batteries that have run out of power can not be added with distilled water to restore power, nor can they be discarded at will, and discarding dry batteries at will will cause pollution to the surrounding environment, so the used batteries should be put into a special garbage bin and properly disposed of.

Distilled water cannot be added to the dry battery, and water entering the battery is counterproductive, not only does it not increase the power but also dilutes the electrolyte.

Dry batteries are also maintenance-free, and since they are maintenance-free, they do not need to be added. If you have to add it, it is estimated that the battery cap will face cripplement!

You can add it, but if you are not a professional, please do not add, if you have to add it, please ask a professional to get it, which will make your battery life longer.

No.

The "dry battery" of non-rechargeable battery is a disposable consumable, after the power is exhausted, it can not be charged, it can not be added with water, it can not be thrown at will, adding distilled water has no effect, charging is prone to danger, and littering is harmful to the environment and soil.

Distilled water is not allowed on dry batteries.

Lead-acid battery after a period of use according to the situation of water, because lead-acid battery is separated by positive plate lead dioxide and negative plate pure lead soaked in dilute sulfuric acid solution, lead sulfate and water are generated when discharged, reduced to lead and lead oxide and sulfuric acid when charging, in the process of charging and discharging, a small amount of water evaporation at high temperature leads to an increase in sulfuric acid density, sulfide into lead sulfate crystals can not be reduced to lead oxide, and the resistance increases, self-discharge increases, should be tested sulfuric acid concentration after discharge and add distilled water, do not reduce the sulfuric acid concentration voltage drop too much, pulse charge, Keting long lead-acid battery life.

The electrolyte of the battery is made of sulfuric acid and distilled water in proportion, and the heat generated during the use of the battery will evaporate part of the water, resulting in the imbalance of the electrolyte ratio, and even the concentration of sulfuric acid becomes larger to form corrosion. If you replenish ordinary water, the impurities contained in it will be deposited in the electrodes, causing insufficient or even impossible charging, so distilled water must be used.