What should I do if the freezer door cover is not tight? What is the reason why the lid of the new f

The refrigerator door will not be tightly sealed for a long time, I believe many friends have encountered this situation, the refrigerator door is not tightly sealed, not only the refrigerator food freshness decreases, but also increases the power consumption of the refrigerator, causing the refrigerator door to be not tightly sealed There are various reasons, the following is to introduce several simple repair methods.

Turn on step-by-step reading mode.

Tool material: refrigerator. How it works:

Cleaning method: When there are oil stains or stains on the hands to open and close the refrigerator door, it is bound to bring the dirt on the hands to the edge of the refrigerator door, and these stains will make the refrigerator door not close tightly after a long time.

Hair dryer. Method: In places where the refrigerator door is not tightly sealed, use hot air from a hair dryer.

Blow on the front for a while, pay attention to the time, as long as the seal of the refrigerator door becomes soft, and the deformation of the seal will be restored in a minute or two after stopping the blowing, and the door can be closed tightly.

Hot water immersion method: When the door of the refrigerator is not closed tightly, we can remove the seal on the refrigerator door, soak it in water at a temperature of about 60 degrees, try to soak every place, take it out in about eight minutes, gently straighten the deformed place of the seal, and then install it, and the situation that the refrigerator door is not tightly sealed will be solved.

Chip removal method: the seal of the refrigerator door is magnetic, and has a certain adsorption of iron filings, and some fine iron filings will inevitably be adsorbed on the seal after a long time, we can clean it with a rag regularly, as long as the refrigerator door seal is not tight due to this reason, it can be solved.

Leak filling method: we can find the location of the refrigerator door leakage, and then stuff cotton or small paper balls into the inside of the seal at the corresponding position to plug the leakage, and the way to find the leakage can be to put a flashlight in the refrigerator, and then close the door to see where the light can be seen around, so as to determine the location of the air leakage.

Bracket adjustment method: If it is found that the reason for the refrigerator door seal is not tight is caused by the fact that the box body and the door are not parallel, we can use tools to adjust the bracket of the fixed door and adjust the two to a parallel state, and the situation that the refrigerator door seal is not tight will be solved.

Direct replacement: If the seal of the refrigerator door is not tightly sealed, the above methods cannot be solved, that is, the seal is aged for a long time, resulting in the door is not tightly closed, and the air conditioner leaks and costs electricity, it is better to buy a refrigerator door seal directly to replace it, ** is not very expensive, generally bought by length, very convenient.

1. Use a hair dryer to heat the sealing strip, the refrigerator door is not closed tightly, it is very likely that the sealing strip on the door is deformed, we only need to take the hair dryer at home to turn on the hot air to blow the sealing strip for a few minutes, you can make the sealing strip back in place, so as to solve the problem.

2. Soak the magnetic stripe in boiling water. Cut several corners of the sealing strip with a knife, then pull out the magnetic stripe, soak it in boiling water at about 70° for about 20 minutes, and then reinstall it, and seal the four corners with sealant.

3. Use the refrigerator tray to keep the door level. It is also possible that the ground is significantly uneven, causing the refrigerator door to tilt and close tightly. Buy a bracket to place at the foot of the refrigerator to keep the refrigerator level as a whole.

4. Wipe the foreign objects on the door seal. Wipe the oil and foreign matter, especially some iron filings or metal powder sticking to the door seal, which will greatly reduce the magnetism of our door seal, resulting in the phenomenon that the refrigerator door is not closed tightly, and the seal should be cleaned regularly to keep it clean.

5. Replace the new sealing strip. If none of the above methods work, it means that the sealing strip of the refrigerator is too seriously aged, and the sealing strip can only be replaced with a new one. However, it should be noted that the size of the purchased sealing strip should match the refrigerator door, and try to choose strong magnetism.

If the freezer door lid is not tight, see if there is ice on the freezer, if there is ice, remove the ice cube to cover it tightly. If that doesn't work, replace the seal on the door.

If the freezer door cover is not tight, the cause should be found through testing. Replace the sealing strip if necessary.

If the freezer door is not tightly covered, first look at whether the vertical line of the door strip is damaged, if the door strip is damaged, it is best to replace the door strip.

Because they are not tightly covered. It can neither guarantee the temperature of the freezer, nor can it effectively save energy, so it is still necessary to find professional personnel to repair it.

If the popsicle is not tightly covered, it may be that the seal is not working well, and you should find someone to change it for you.

If the seal is broken, just change the seal, and at the same time see if the ice is too full, and it will not cover tightly, so just take out a little something.

What should I do if I don't keep the freezers? That must have been forgotten, and if you don't have a concept, it will definitely cost electricity.

Summary. Hello, the freezer door cover is not tight, 1, it is too much ice on the inside of the freezer lid, which causes the freezer lid to be not tight. It's OK to do a de-icing, 2, the sealing strip falls off, solution:

Cut the glued part of the four corners of the door seal with work, pull out the magnetic strip, remove the door seal, soak the deformed door seal in hot water at about 60 degrees Celsius, turn it from time to time, remove it after seven to eight minutes and put it on the platform, and gently straighten it. Once cooled, the curved door seal will be flat and straight again.

Dear I will do this question, typing, it will take a little time to check the information, and please be patient.

How long to wait. Hello, the freezer door cover is not tight, 1, it is too much ice on the inside of the freezer lid, which causes the freezer lid to be not tight. It's okay to do a de-icing, 2, the sealing god faction burner falls off, and the method of solving the game is virtual:

Cut the glued part of the four corners of the door seal with work, pull out the magnetic strip, remove the door seal, soak the deformed door seal in hot water at about 60 degrees Celsius, turn it from time to time, remove it after seven to eight minutes and put it on the platform, and gently straighten it. Once cooled, the curved door seal will be smooth and straight again.

Is the door deformed?

It's unlikely that the door will be deformed, see if there's too much ice. De-icing will do the trick.

Cleaned. If the lid is still not closed tightly after de-icing, check that the screws on the freezer lid are properly installed, loosen the screws with a tool, or tighten the screws.

Summary. In this case, I adjust the screw with a tool. In the case of new freezers, there are cases where the lid is not tight. Then it is caused by the screws on the freezer lid are not installed properly, loosen the screws with a tool, or tighten the screws.

In this case, Wu Qiao adjusts the screws with a tool. The new freezer has a situation where the cover is not tightly dusty. The screws on the freezer lid are not installed properly, so loosen the screws with a tool or tighten the screws.

The reasons and solutions for the freezer lid is not tight as follows: 1. Treat the ice on the freezer lid. If there is too much ice on the inside of the freezer lid, it will lead to a loose freezer lid.

At this time, it is enough to do a de-icing. 2. Use a tool to adjust the screws. If it's a new freezer, there's a bad lid.

Then it may be caused by the screws on the freezer lid are not properly installed, loosen the screws with a tool, or keep an eye on the screws. 3. There are too many things in the freezer. If there are too many things in the freezer and the freezer lid does not close, then take out some or adjust the position appropriately.

4. Replace the old sealing strip. The freezer's seals can also cause the lid to be loose if they are too long. At this time, replace the seal of the secret finger and you can cover it.

5. The lid of the freezer is out of shape, resulting in a loose cover. If the freezer has been used for a long time and the lid has been out of shape, then you can only change the lid or ask a professional master to deal with it.

The reason why the lid of the new freezer is not tight is that the screws on the freezer lid are not properly installed, in this case, loosen the screws with a tool, or tighten the screws.

Thank. You're welcome!

The above is all my reply, I hope it can help you and I wish you a happy life

Do you have any other questions? We'll be happy to continue to answer your questions

Don't forget to like it! Thanks for your support!

Hello dear and happy to answer for you. Hello dear, the freezer is not tight, the answer is expected to be caused by loose screws, oh dear. You can do this by following these steps:

The first is to adjust the screws with a tool. If it's a new freezer, there's a bad lid. Then it may be caused by the screws on the freezer lid are not installed properly, loosen the screws with a tool, or tighten the screws.

Kiss the answer: The Lord recommends that you travel during the epidemic, please do a good job of personal epidemic protection, remember to wear a mask, and remember to wear a mask. I hope that the answer of the Lord can help you, and I wish you a happy life