After using the Joyoung brand electric kettle for a period of time, the cover is not tightly closed,

If the lid is loose or broken, you can find an after-sales service for repair.

Proper use of the electric kettle:

1. After understanding the principle of the electric kettle, it is necessary to understand that the electric kettle will produce a certain amount of scale after heating, and if you want to extend the service life of the electric kettle, you need to clean up the scale in the electric kettle regularly, so as to enhance the heating efficiency of the electric kettle, and at the same time protect the thermostat of the electric kettle.

2. The correct use of the electric kettle is also a way to extend the service life of the electric kettle. When using an electric kettle, it is the most basic principle to follow when adding water and then turning on the electricity, otherwise it is easy to cause the heater of the electric kettle to burn empty, which will not only damage the thermostat of the electric kettle, but also cause a fire in serious cases.

3. When using the electric kettle, its water level needs special attention, the water level of the electric kettle is generally at least 3-5 cm higher than the heater, and the water level is the most important factor to ensure the service life of the electric kettle heater.

4. According to the principle of electric kettle, the power used by the electric kettle is also a factor to extend the electromagnetic service life, and the power used by the electric kettle also has certain requirements. Avoid excessive power of other electrical appliances and reduce the voltage of electric kettles.

If the cover is not tight, it may occur: 1. The cover is deformed, replace the upper cover, 2. If it is a material cover, press it to mediate 3. If the cover has a lock, see if the spring falls off If it falls off, it is very simple to reinstall it, such as replacing the lock if it is broken.

If the above reasons can't be solved, find after-sales solutions, I hope it can help you.

Joyoung. The lid of the electric kettle can not be covered, it is generally a problem of the spring, remove the screw rod up and down the pot handle, you can take out the lid to see if the spring that buckles the lid is misplaced, and the spring can be repaired by resetting.

1. The lid of the newly bought thermos cup cannot be covered because the lid and the cup mouth do not match, and it can be replaced free of charge before the warranty period.

2. Reason: If the quality of the new thermos cup is clear, the following two conditions must be met to prove that the quality is fine.

1. It feels difficult to screw: The new thermos cup feels difficult to screw because the sealing ring is new, and there are seams and no wear, so it will feel as if it is difficult to screw.

2. Seeing that there is a seam, it is because of the unevenness caused by elastic force, from another point of view, on the contrary, this is a truly new and untouched product, because the seal is tight and elastic enough, it will not leak.

3. Precautions:

1. With the increase of the number of uses, the faster the loss of the sealing ring (this is a consumable), so it needs to be replaced once a year.

3. When the lid is infinitely close to the cup body, it means that the seal has been seriously damaged, and a new thermos cup needs to be replaced to drink water.

The electric kettle is constantly charged by itself, and the lid is not tightly repaired, and it can be repaired if you have the skills to do so:

1. The working principle of the steam temperature control switch on the handle of the electric kettle is that when the lid of the kettle is tightly covered, the hot water steam boiling will automatically cut off the power, and the switch can only be turned on after the temperature drops;

2. Take a closer look at the lid, and the factors that are not tight should be excluded;

3. The cover will not be tightly covered if it is deformed, and it needs to be replaced with a cover of the same model, and the cover can be tightened to make the handle switch action; Otherwise, even if you change the steam temperature control switch on the handle, it will be in vain.

The lid of the Joyoung electric kettle can't be covered, so you can remove it and take out the spring. After taking out the spring, drag it out and stretch it, and then install it in.

The lid of the boiling kettle does not support personal disassembly, if it has been disassembled, it needs to be processed by the after-sales service department

If you have a little hands-on ability, you can take it apart to see, but you don't need to disassemble the bottom of the pot to deal with this, just start to disassemble it from the handle of the pot, I'm afraid there is a problem with the pneumatic switch or spring part inside.

During the operation, I am afraid that I will forget to take pictures at any time to avoid not being able to go back after installation.

It should be a problem with the lid of the pot, and it is not easy to repair it yourself, so you can go to the maintenance place to repair it.

This electric kettle may be the deformation of the lid caused by boiling too much water, so you can't repair it yourself, it's better to buy a new one, and it doesn't cost much, and then you have to find a professional home appliance repair master to repair it for you.

If the white steel scale is used for a long time, it may also be deformed, and special machinery is required to correct it. Because it is an electric kettle, in order to use it safely, it must be returned to the manufacturer or repaired in a specialty store to ensure the safety of use

What does a broken expansion kettle lid look like?

Summary. What's going on with the electric kettle popping up when you press it Disassemble the U-shaped reed inside, swap this reed down, it's fine, turn the kettle upside down, press the switch, and it won't jump open. The working principle of the electric kettle is that the water vapor generated when the water boils deforms the bimetal sheet of the steam temperature sensing element, and this deformation pushes the power switch to power off through the lever principle.

It is not self-resetting when it is powered off, so the kettle will not automatically reheat after the power is off. Can an electric kettle heat milk It is best not to use a water heater to heat milk directly, otherwise it will easily overflow. Heating milk at high temperatures will lose nutrients, and the kettle is heated unevenly, and the milk stains left by the milk are more difficult to clean.

Hot milk is accidentally overflowing the pot and more dangerous, resulting in a short circuit in the line, electric shock and the like, and it may also occur**. It is recommended to use a glass container to steam in water, or the microwave oven has a function button to heat the milk, and it is generally good to heat it for 40 seconds.

What's going on with the electric kettle popping up when you press it Disassemble the U-shaped reed inside, swap this reed down, it's fine, turn the kettle upside down, press the switch, and it won't jump open. The working principle of the electric kettle is that the water vapor generated when the water boils deforms the bimetal sheet of the steam temperature sensing element, and this deformation pushes the power switch to power off through the lever principle. It is not self-resetting when it is powered off, so the kettle will not automatically reheat after the power is off.

Can an electric kettle heat milk It is best not to use a pie water heater to heat milk directly, otherwise it will be easy to overflow. Heating milk at high temperatures will lose nutrients, and the heating of the kettle is uneven, and the milk stains left by the milk are more difficult to clean. It is also more dangerous to accidentally spill hot milk, resulting in short circuits in the line, electric shock, etc., and there may also be explosions.

It is recommended to use a glass container to steam in water, or the microwave oven has a function button to heat the milk, and it is generally good to heat it for 40 seconds.

What to do if the kettle smells 1. Boil orange peel, warm water and vinegar or refrigerator deodorant 2. If it is left for too long, put the bamboo charcoal inside and store it again after each use. If you use it often and there is a peculiar smell, it may be that the water quality is not good, or you have burned other things with Wu Yu, and it is not clean after use. Solution:

Bamboo charcoal is best, others such as orange peel, aged vinegar, or refrigerator deodorant. 3. This should be the result of the heat generated by the power cord or the heat of the plastic part on the pot body, as long as you boil water, it should have a taste. 4. I have a method, which was originally used to drink kung fu tea.

You use this kettle to boil tea once, and it is well known that tea leaves have a good deodorizing effect.

Dear, hello, I'm glad to answer for you: Joyoung kettle switch is normal or not working? A:

1.The electric kettle is broken but the power switch is normal If the power switch is normal, the fault mostly occurs in the insulation switch. First of all, see whether the reed of the bimetal sheet is pressed against the switch contact rod, if it is pressed too tightly, you can use tweezers to bend it upwards until the distance between the two.

If the distance between the bimetal sheet and the switch lever is normal, the switch box should be disassembled, and the contacts and reeds of the insulation switch should be cleaned and repaired. 2.The indicator light is on, indicating that the power supply has been added to the indicator circuit, and the fault is in the electric heating pipe or its connecting part, and the common electric heating pipe is damaged and the contact is poor.

Remove the electric heating pipe and measure its resistance value. The electric heating pipe is damaged and can generally only be replaced. The poor contact is mainly due to the serious corrosion or deformation of the contact reed in the power plug assembly, which can be disassembled and repaired by the switch box, and it is best to replace it with a new one if the damage is serious.

3.The water cannot boil and the power cannot be cut off, mainly due to the failure of the reset switch. The common reason is that the temperature sensor is seriously deformed or the action of the switch connecting rod is blocked, I hope that Tong Tiechen can help you, I wish you a happy life, if I am helpful to you, please give me a 5-star like, thank you for your support to me.

Hello: How can the lid of the electric kettle not cover the reason for the fact that the lid of the electric kettle cannot be covered, which is generally a problem with the spring.

Summary. Hello according to your problem description: If your Joyoung health pot is faulty, you can try the following methods to solve the problem:

1.The lid won't open: Check if the lid won't open due to water vapor and pressure.

You can cool it down for a while before trying to open it. 2.You can't add water to the pot:

Check that the lid is closed tightly and that the spout is not clogged. 3.The temperature of the water in the pot does not rise:

Check whether the heating base is energized, whether the heating base and the bottom of the pot are close together, and whether the keep warm button is turned on. 4.The water temperature in the pot is too high:

Check that the keep warm button is closed, whether the heating base and the bottom of the pot are separated, and whether the heating base is overheated.

Hello according to your problem description: If your Joyoung health pot is faulty, you can try the following methods to solve the problem:1

The lid cannot be opened: Check if the lid cannot be opened due to water vapor and pressure. You can cool it down for a while before trying to open it.

2.The kettle cannot be filled with water: check that the lid is closed tightly and the spout is not clogged.

3.The water temperature in the pot does not rise: check whether the heating base is energized, whether the heating base and the bottom of the pot are close together, and whether the hand temperature button is turned on.

4.The water temperature in the pot is too high: check whether the keep warm button is closed, whether the heating base and the bottom of the pot are separated, and whether the heating base is overheated.

How to deal with it. Hello, can you specifically describe the problem that occurred<> the water was cold on the second day of insulation, and then the word end appeared, and the pot was only bought for more than a month.

Hello, if you find that the water is cold the next day, it means that the heat preservation function of the health pot has not achieved the expected effect. There may be several reasons for this problem:1

If the health pot is not filled with water or the water temperature does not reach the set temperature when the water is added, the holding time will be affected, even in the state of heat preservation, it may cause the water temperature to gradually drop until it becomes cold. It is recommended that you fill up the water when adding water, and wait for the health pot to heat up to the set temperature before setting the holding time.

2.The thermal insulation function of the health pot is damaged: If the thermal insulation function of the health pot is damaged, it will also lead to poor thermal insulation effect.

It is recommended that you check whether the equipment is operating normally, especially whether the heating and heat preservation functions are normal. 3.External environmental influences:

The thermal insulation effect of the health pot is also affected by the external environment, such as surrounding temperature changes, light and other factors will affect the thermal insulation effect. It is recommended that you keep the environment of the health pot stable and pay attention to the holding time when you use it. If the above methods cannot solve the problem, it is recommended that you contact Joyoung after-sales service center.