What are the advantages and disadvantages of floor heating What are the specifications and standards

<>1. Paste the corner insulation strips.

2. Lay green feather extruded plastic board.

3. Paste aluminum foil tape.

4. Lay the green feather aluminized reflective film.

5. Fix the green feather coil.

6. Lay the green feather silicon crystal network.

01.Paste the corner strips, the corner insulation strips should be pasted on the wall of the heating area to prevent heat from dissipating through the wall, and the wall should be cleaned to prevent falling off before laying.

02.Before laying the green feather extruded plastic board, the original ground should be smooth, and the extruded plastic board should be spread flat on the ground. Pay attention to the seams between the extruded plastic boards, as tight as possible.

03.In order to prevent heat from being lost from the gaps, aluminum foil tape should be used for both the extruded board and the boundary strip between the extruded board and the gap between the extruded board.

04.Laying the green feather aluminized film, the reflective film should be laid flat to minimize wrinkles. The reflective film should be laid with neat squares, and the laying should be covered tightly, and there should be no leakage.

05.When fixing the ground coil of the green feather coil, the kart should be fixed with kart, and the kart should be inserted vertically into the extruded plastic board, and the amount of cart used should be strictly controlled to prevent excessive use and damage to the ground extruded plastic board.

06.Laying the green feather silicon crystal mesh, laying the silicon crystal mesh above the floor heating pipes. In order to facilitate backfilling, Karting can be used to fix both ends of the silicon crystal grid, and care should be taken when backfilling to avoid scratching the pipe.

Kiss! Hello, happy to answer your <>

Pro-floor heating installation basis: for floor heating construction, the main specifications and standards are as follows:

The national standard "Unified Standard for the Acceptance of Construction Quality of Building Engineering" GB503002, the national standard "Code for Acceptance of Construction Quality of Building Water Supply and Drainage and Heating Engineering" GB50242-2002 Industry Standard "Technical Regulations for Ground Radiant Heating" JGJ142-2004 Floor heating is the abbreviation of radiant floor heating, which is radiant floorheating in English, and uses the entire ground as a radiator. Water floor heating refers to a heating method that heats water to a certain temperature and transports it to the water pipe cooling network under the floor to achieve the purpose of heating through floor heating. The low-temperature floor heat medium forms a gradually decreasing temperature gradient from the soles of the feet to the head indoors, thus giving people the comfort of warm feet and cool heads.

Ground radiant heating is in line with the fitness theory of traditional Chinese medicine, which is the most comfortable heating method at present, and is also a symbol of modern quality of life. It is divided into two categories: water floor heating and electric floor heating from the thermal medium quality, and is divided into wet floor heating and dry floor heating from the pavement structure. From the surface decoration material, it is divided into floor type floor heating and floor tile type floor heating; Functionally, it is divided into ordinary floor heating and far-infrared floor heating. Hope mine can help you <>

Do you have any other questions?

The main specifications and standards for underfloor heating construction are as follows:

1. The national standard "Unified Standard for Acceptance of Construction Quality of Construction Projects" GB50300

The "Unified Standard for Acceptance of Construction Quality of Construction Projects" is based on the Notice on Initiating the Preparation of Construction Technology Standards (Construction Technology Standards of China State Construction Corporation) issued by China State Construction Engineering Corporation (hereinafter referred to as China State Construction Corporation) Zhong Jian Ke Zi No. 2002 389.

It is jointly compiled by the quality management department of China State Construction Engineering Corporation in conjunction with China Construction First Bureau (Group), China Construction Second Engineering Bureau, China Construction Third Engineering Bureau, China Construction Eighth Engineering Bureau and other units.

2. National standard "Code for Construction Quality Acceptance of Building Water Supply and Drainage and Heating Engineering" GB50242 2002

Code for Construction Quality Acceptance of Building Water Supply and Drainage Heating Engineering" is a book published by China Building Industry Press in 2002, covering building water supply and drainage, heating engineering and construction quality acceptance.

3. Industry standard "Technical Specification for Ground Radiant Heating" JGJ142 2004

In order to standardize the design, construction and acceptance of ground radiant heating projects, to achieve advanced technology, economic reasonableness, safety and application, and to ensure the quality of the project, these provisions are formulated.

This specification is applicable to the design, construction and acceptance of ground radiant heating projects in new industrial and civil buildings with hot water as the heating medium or cables as heating elements. The design, construction and acceptance of ground radiant heating projects, in addition to complying with these provisions, shall also comply with the relevant national mandatory standards.

For the time being, there has not been a unified national standard, but the national standard for floor heating construction "Ground Radiant Heating Technical Regulations" has begun to be revised, if the floor heating pipe is too thin, it will cause uneven heat dissipation, if it is too dense and will cause invisible waste, so it is necessary to choose a regular floor heating construction unit, which is more professional.

Floor Heating Installation Standards:

2. The laying spacing of floor heating pipes, the sunny side is 25-30 cm and the shaded side is 20-25 cm 3. The use of water separators, a water separator can lay an average of 50-75 meters of floor heating pipes, that is, about 17 square meters.

There are no underfloor heating pipes on the balcony, and there are no regulations in the state to collect money or not.

Although many families in southern cities do not have centralized heating, they will choose to lay floor heating in their own homes, which can be warm in winter, and laying floor heating is also particular. So what are the specifications and requirements for installing underfloor heating?

1. If you want to install floor heating at home, you need to make preparations in the early stage, clean the scene, install temperature control lines, and water separators.

2. The temperature control line should be buried in advance, and the water separator should be installed to the designated position, and then the floor heating pipe can be laid.

3. Before laying, it is necessary to cut the insulation board according to the size and size of the room, and then lay, and then lay the reflective film and steel wire mesh, and finally the pipeline can be laid.

4. After the pipeline is laid, it needs to go through the pressure test, inject water into the pipeline, press it with a special press, hit it to 10 kg, wait for a day, if the pressure is not less than 6 kg, it means that there will be no leakage.

China has very strict standards for the installation of floor heating, from design to material selection to construction, all need to be in accordance with certain specifications. What are the specifications and requirements for floor heating installation? Let's take a look.

1. The length of each heating pipe should not exceed 120 meters. In the selection of materials, the thickness of the benzene board is required to be 2-4 cm, and during construction, there must be a leveling layer, a moisture-proof layer, a thermal insulation layer, etc., and the thickness is between 8-11 cm. In order to ensure safe use, these installation specifications and standards need to be strictly adhered to.

2. Floor heating installation and decoration are synchronized. The installation of underfloor heating is generally synchronized with the decoration of the home. There are two phases of floor heating, the early stage is at the beginning of the decoration, after the completion of water and electricity, the installation of water collectors and laying pipes; In the later stage, after all the decoration of the home is completed, the wall-hung boiler is installed and debugged, and the debugging is correct.

3. The details of floor heating pavement are very important. The layout of floor heating pipes is more complicated than that of Narot, and it is necessary to calculate the spacing and laying shape, and if the pipes are not balanced, there will be a local situation of no heat. It is also necessary to pay attention to the choice of insulation materials, if the insulation materials are not good, it will dissipate heat downstairs, affect the comfort experience, and may also cause the release of harmful substances.

4. After the floor heating is completed, it needs to be debugged. After the installation of the wall-hung boiler is completed, the floor heating must be commissioned. It is strictly forbidden to operate the floor heating system without commissioning.

The commissioning of the whole system is carried out under the condition that all water sources, power supplies, and hot water return are in place. During the commissioning, it is also necessary to be present to supervise, and the commissioning can only be signed after the commissioning is completed.

5. The ground cannot be punched. When decorating, pay attention not to punch holes and nails on the ground, so as not to leak the floor heating coil and cause water leakage; After the decoration is completed, it is strictly forbidden to punch holes and nails after laying the floor, if you accidentally penetrate the floor heating pipe, it will be very troublesome to solve.

6. Do not place furniture with a large contact area directly on the floor. Since the surface of the floor is a heat dissipation surface, try not to make fixed decorations or install legless furniture on the floor, so as not to affect the flow of hot air and cause poor heating effect in the room.

I believe that the use of floor heating friends are not unfamiliar, especially in the cold winter, most people will use it, it can make the cold winter day warmer, for the installation of floor heating is not an easy task, there are many matters to pay attention to and specifications, so what are the floor heating installation specifications and requirements? Let's take a look with Xiaomeng Zen Fiber, I believe it will bring you different insights.

1. For the safety of use, the length of each heating pipe shall not exceed 120m, and the thickness shall be controlled between 8 and 11 cm. 2. The installation of floor heating and the construction of the living room should be synchronized. 3. Floor heating must be debugged after the construction is completed to ensure that it is correct before it can be used.

How to choose the right floor heating.

1. Service providers are very important.

Because the construction of floor heating is a project that requires high technology, if it is not installed by professionals, it is easy to have problems in the later stage, so it is very important to choose a service provider with a high degree of credibility, and they are more trustworthy in terms of product quality and after-sales service.

2. The quality of auxiliary materials should not be underestimated.

When placing floor heating, many people will ignore the selection of auxiliary materials, especially in the current messy building materials market, all kinds of uneven floor heating materials, so we must be cautious when choosing, do not be too greedy for small favors, otherwise once there is a problem, there will be a lot of trouble in the later stage.

3. Space area.

For places with a larger heating range, it is recommended to choose water floor heating, and a smaller range is suitable for electric floor heating, because the space is larger places, if electric floor heating is used, due to the insufficient power value of the household, it will cause the electric heating to be unable to use normally, at this time it is recommended to use water heating is more appropriate, if the range is small, if the use of water floor heating will increase the economic burden.

Summary: What are the above specifications and requirements for floor heating installation, and how to buy floor heating correctly are introduced here, hoping to provide you with some help. If you want to know more about decoration, you can pay attention to the relevant information of Qeeka Home.