How to remove the air conditioner filter and clean it

Before disassembling the cabin air filter, carefully open the cabin air conditioner case. Generally, there are two small slots in the air conditioner shell, and the outer cover can be gently pulled outward. After opening the cover of the air conditioner, there are often two buttons inside, which need to be gently opened to make the cover fully open.

Then take the filter. The filter is easy to hold, but it gets stuck in a couple of card slots. Filter it first...

After the filter screen is removed, some air conditioners have black particles, and the filtration is enhanced, so they should be removed separately for cleaning and drying. Then carefully rinse the filter with clean water a few times, brush it a few times with a soft brush, and finally ventilate...Remove the strainer, take the water pipe, and rinse with tap water.

Don't use dish soap or anything like that, just rinse it and you're good to go. Please dry in a cool place, not in the sun. The filter screen is generally plastic and resistant to high temperatures.

Air conditioner filter cleaning method:

1. Before disassembling and washing the air conditioner filter, the power supply should be disconnected to ensure safety.

2. Turn on the air conditioner panel switch, one on each side of the air conditioner.

3. Buckle outward at the same time.

4. Buckle the panel to see the filter.

5. Lift up the filter screen buckle.

6. Then you can remove the filter with one pull.

7. Rinse the filter with clean water.

Precautions for cleaning the air conditioner filter.

1. When cleaning the air conditioner filter, you should remove the dust filter on the surface first according to the instructions in the manual. During the disassembly process, the metal parts of the indoor unit should not be touched, because these metal parts are very sharp and easy to be scratched.

2. The water temperature used for cleaning should be lower than 50 degrees Celsius, and detergents such as washing powder and detergent should not be used, otherwise the filter dust net will be deformed.

3. The filter screen cannot be directly brushed with a hard brush when cleaning, so as to prevent damage to the filter screen and affect the filtration effect of the air conditioning filter. Sponges should also not be used, as sponges can damage the surface of the filter and cause some wear and tear.

4. After the air conditioner filter is cleaned, you need to wipe the dust filter with a soft towel and dry it in a cool position.

The method of removing and cleaning the filter screen of the air conditioner is as follows:Tools Raw materials: air conditioner, filter, faucet.

1. Unplug the outlet of the air conditioner.

2. Open the panel of the air conditioner and you can see the filter.

3. Gently push up and pull down to remove the filter.

4. The filter can be cleaned directly under the faucet, and can be gently brushed with a brush.

5. Place the filter screen in a ventilated and dry place to dry.

6. After drying, the filter can be installed.

7. When installing, you only need to gently send the filter to the inside, and then send it to the next card to complete the disassembly and washing.

How to remove and clean the filter screen of the air conditioner:Tools Material: Gree air conditioner, detergent.

Method Steps:

1. First of all, cut off the power supply of the air conditioner to be cleaned.

2. Open the air conditioner panel from both ends (directly buckle open, no tools required) and you will see two air conditioner filters.

3. Just pull out the two filters directly by hand.

4. Put the extracted filter into the water to clean (there is no soft brush and add a little detergent).

5. After washing, it is much cleaner and can be dried.

6. Install the dried filter back into the air conditioner, and cover the air conditioner cover directly. Next time, you can use it directly, clean and healthy is as simple as that.

Here's how:1. Open the front panel with air conditioning. The specific method is shown in the following figure:

2. Slowly push the air conditioner filter inward along the frame. The specific method is shown in the following figure:

3. Insert the lower edge of the filter into the card slot. The specific spike reed method is shown in the figure below

4. The same method is used for the filter on the other side. The specific method is shown in the following figure:

5. Cover the lid of the air conditioner with the back of the state. The specific method is shown in the following figure:

The method is as follows: Step 1: If there is a manual, first see if the manual has a specific air conditioner cover structure and a method of dismantling the network. If not, here are the common methods.

Step 2: Open the empty flush alarm shell, pay attention to be careful, usually there are two small card slots stuck, gently pull the outer cover outward.

Step 3: After opening the outer cover, you will also see that there are two buckles inside, and you have to gently pick open it to make the outer cover fully open.

Step 4: At this time, you can take off the filter screen, the general filter screen is stuck in the card slot, you only need to push the filter screen up slightly, and the bottom will be out of the card slot, and you can take the past with a little hand drag.

1. Open the outer panelStand in the direction of keeping it level with the air conditioner and open it to the outside of the burying pie outside to bend the greeting board.

2. Expose the filterWhen you open it, you can see that the filter is exposed.

3. Push open the filterGently push the filter away with your hand.

4. Pull out the filterBuckle both sides and pull out the filter of the air conditioner.

5. Successfully take it outFinally, the air conditioner's filter was successfully removed.