What should I do if I find that the wall is uneven and has sand holes during the acceptance?

Introduction: During the acceptance, it was found that the wall was uneven, and there was a trachoma, it is recommended that you and the third-party engineering quality supervision unit re-apply for verification, mainly because we are not qualified to refuse to sign, and once they repair the problem, we can ask the developer to compensate for economic losses. The quality of the house must not be ignored, if you ignore it now, it will also cost a lot of money to repair it later, so it must be done at one time.

1. The third-party engineering quality supervision unit can apply for re-verification

The decoration of the house needs to be paid special attention, a little attention may appear some hidden pits, these pits we did not find in the early stage, and it will cost a lot of money to make up for it in the later stage.

It is recommended that we apply for re-verification with the third-party engineering quality supervision unit, as long as the quality is unqualified, then we can have the right to terminate the contract and require them to compensate. <>

Second, if there is a problem in quality, you can apply for compensation, and let them fix it

We must check the quality of the wall when we inspect the house. The first is verticality.

As long as these things affect our normal residence, we can request to terminate the contract and compensate for the loss of quality, and we can also ask the seller to repair and compensate. <>

3. Be extra cautious and careful when inspecting the house

And when we inspect it, we also have to see if there is a hollow drum on his wall, we can't not check it because it is not easy to check, there must be a new oxygen.

Be sure to see clearly, for all the ingenuity to complete the inspection through percussion, you must know that once the wall is hollow, it is easy to cause the wall to crack and fall off, and the later use effect has a very big impact. It costs a lot of money to buy a house, and it costs a lot to renovate a house, so we can't spend money and not see a real return.

You can apply some quicklime water to the wall to make the surface extra flat, or you can put some stickers on it to cover the unevenness of the potholes.

As with the renovation workers, let the renovation workers renovate, or you can indirectly use sandpaper to polish the original foundation, or you can or may scrape a new layer of putty.

Communicate with the decoration workers, let the decoration workers renovate, or you can directly polish with sandpaper on the original basis, and you can also scrape a new layer of putty.

These parts should be reflected, and it is hoped that the renovation workers will change this situation, and then carry out corresponding inspections, and must reflect such a situation to the property management.

After the renovation, the wall surface is uneven- First of all, the wall is uneven, not only visually uncomfortable, but after placing the furniture, the overall effect will decrease, as if it is somewhat tilted, which is very unpleasant, so if there is an irregular wall, it is necessary to level the painting.

After the renovation, the wall surface is uneven- Secondly, if in this case, the decoration of the building is adopted, the acceptance can be refused, and the request for treatment must be ensured, it must be ensured that the repair will not be carried out in the future; We must also supervise, but not before. First of all, I know a little bit about this.

After the renovation is accepted, the wall is uneven - second, the wall is divided into three situations. One of them is that most of the front remains flat, but locally unevenAfter the renovation, the wall surface is uneven-Thirdly, most of the irregularities are less than 1 cm, and thirdly, there is a certain error in the flatness of the surface of the wall. More than 1 cm;

Fourth, there are local violations. This situation is best handled. It is usually applied directly on the basis of the original putty, and then the sandpaper is then compared to the entire wall. Once the flatness is confirmed, you can paint.

Fifth, when inspecting the surface of the wall, it was found that there was a certain error in the flatness of the front, and the error was within 1cm. If the bottom of the wall is made, you can apply 1 2 cm of putty directly in front and then flatten it. If the bottom of the wall is not good, you need to shovel the original wall with cement mortar and plaster and level it again, and then brush the putty with sandpaper.

Sixth, if there is a straightness error in a large area larger than 1 cm in front, please observe how the front base is made. If necessary, scoop the entire wall and smooth out the cement and plaster. If the error is too large, you should use plaster.

Place the board, then putty, on the drywall, sandpaper and then paint.

The above isAfter the renovation, the wall surface is unevenI hope the brush will help you.

We first have to look at the wall of the house, it is best to take a small piece of wood in our hands, knock on the wall, listen to see if there is a hollow drum sound, this is easy to hear, if the wall is not real, it will make an empty sound. Check whether the door opening and closing is smooth and flexible, and whether there is any abnormal noise; whether the closure is tight; When the door is opened, whether the handle hits the wall; whether there is a phenomenon of "door fighting"; Tsuneshi-kun personally believes that the first thing to pay attention to is to inspect the house procedures. Check whether the house is the house you have purchased, if you are not satisfied with the purchase contract, accessories and supplementary agreement, you should ask the real estate agent before moving in, re-check and replace.

<> in the precautions for the inspection of the rough house, the inspection of the wall is very important, and the inspection should be done by gently tapping the wall with your hands, judging whether the wall is hollow from the sound, and visually inspecting whether there are cracks on the wall. There are four common cracks: strength cracks, settlement cracks, temperature cracks, and deformation cracks.

This really doesn't need to be taught