The correct installation method of the floor heating water separator, and where is the floor heating

Underfloor heatingWater separatorsThe correct installation method is as follows:

During construction, the water separator needs to be set at the top, and the water collector is set at the bottom, the distance between the two is 200 mm, and the water collector ** is more than 280 mm from the ground, and the water collector is separated.

Normally, it is supported by a bracket, and during the installation process, it is necessary to refer to the height of the drawing and use expansion bolts.

Lock to the wall and finally attach the manifold to the bracket.

Attention needs to be paid to the installation of the water separator:

1. The location of the water separator needs to be found first, so as to avoid frequent replacement during subsequent maintenance, and to ensure that the position is sufficient, which will normally be set on the wall, the outer layer of the pipe well or the inside of the cabinet under the basin, and determine whether the pipeline system is installed vertically or horizontally according to the position direction.

2. No matter how many roads are divided, the length needs to be controlled, and the problem of insufficient needs to be avoided, such as 70 meters of one road, must be controlled in the corresponding range to avoid too large a gap, otherwise there will be unbalanced force after installation.

3. When installing, the water pipes equipped with each branch can not be interspersed, and the water separator needs to be connected separately from the pipeline of the water point, and the hot and cold water separator can be connected together with a water separator box.

1. For central heating in the community, it depends on the location of the main inlet pipe of the hot water, and the nearest convenient place from this location is the best. Underfloor heating pipes are laid out radially in parallel from the water divider. Because it is a water facility, in order to prevent water leakage and water leakage during maintenance, most of them are placed in the kitchen and bathroom, which have been waterproofed.

In order not to get in the way, in order to be neat and beautiful, it is often hidden, so the vast majority of people are housed in cabinets. Of course, there are also a few people who put them in the dining room and balcony for the convenience of switching.

Second, your own household wall-hung boiler burning, depending on the location of the wall-hung boiler. Generally speaking, gas pipeline safety requirements can only be in the kitchen, not through the living room, dining room, bedroom space. Then the kitchen and the bathroom partition, put it there and put it here, one is to see where there is a place to install and is not awkward or in the way, and the other is to see which side of the pipe laying is more reasonable and convenient.

Then, the kitchen and bathroom are not next door, and the wall-hung stove can only be placed in the kitchen, so the water separator is also best placed in the kitchen. Put it elsewhere, your hot water pipe goes over, the water is divided, and the floor heating pipe has to come back, which is very unsmooth, and the benefit is slightly affected.

Extended information: Floor heating water separator and water collector refer to the device used to connect the main heating water supply pipe and return pipe in the floor heating system.

The floor heating water separator is a water distribution and water collection device used to connect the water supply and return of various heating pipes, and its functions are mainly four items: pressurization, pressure reduction, pressure stabilization and diversion.

It is generally pure copper and resistant to decay; Also available in stainless steel; But never cast iron.

Hello! The floor heating water separator is generally placed in the cabinet under the basin in the bathroom, or the cabinet in the kitchen is concealed, and it is generally not surface-mounted, which not only saves space, but also compounds the aesthetics of the project, if you still feel that the space is relatively small, you can also open a 10 cm slot in the wall of the bathroom, so that the HVAC company can make a control cabinet and hide the water separator in it, which is also very space-saving. Wuhan Junda HVAC Co., Ltd. provides.

Generally, it is installed on the wall below the wall-hung boiler, and the location is required to be easy to operate and easy to discharge. Because the outlet and return water are placed separately, the two must be staggered in a certain position, so that the same outlet pipe and return pipe can be matched and corresponded. The height should be close to the ground, and the installation should be firm and reliable, and it is not easy to be collided and dislocated by other objects.

Hello, the installation location of the floor heating water separator is generally waterproof and has a floor drain in the bathroom; secondly, in the kitchen cabinet or balcony; If it is a duplex structure, the upper and lower water separators are best set on the same set of risers; For public construction projects, it is necessary to consider the symmetrical placement of water separators, especially the narrow swimming pools around them, and to prevent the over-dense arrangement spacing caused by over-dense water separators; Some large studios or floor-to-ceiling glass curtain buildings cannot be set up against the wall, so you can consider placing the water separator at the front desk and adjacent rooms, and for the sake of aesthetics, you can use flower beds or other shapes as the box of the water separator. I suggest you come here for self-study, and I saw it here!

First of all, every room should be installed, the location is far away from the heating closest to the wall or made in the wall, and the boiler is back to the balcony or kitchen.

Priority should be given to the cabinet, preferably in the middle of the whole house, and the underfloor heating company will give advice.

In home decoration, the placement of the water separator is judged by the area and structure of your room, generally two areas, one is the bathroom, the other is the kitchen, because these two areas are floor tile areas, the pipe interface leakage damage furniture, the second is because these two areas have floor drains or drainage pipes, the first is convenient maintenance, and the second is not afraid of water damage to the floor. Generally, the heating area of the room is less than 60 square meters, the kitchen and bathroom can be, and the larger unit should be considered to be placed in the guest bathroom, which is the center of the room, to ensure that the distance from each pipe to each room is balanced, so that there will not be too many passing pipes, waste heat loss, and water flow pressure balance. If it is a villa, there is no doubt about choosing the bathroom.

The water separator is placed in **, the ground temperature is the highest, and you know the consequences if you put it in the kitchen, and the kitchen is relatively hot and ...... when cookingThe floor heating pipe laying area of the bathroom itself is small, so the temperature generally does not reach 18-22 degrees, if the water separator is placed here, the temperature will be Monmonda, and the drying effect is also good.

Generally installed in the kitchen, the bathroom is better.

The underfloor heating separator is installed on top of the water collector because the water separator is installed on top of the water collector because of the high pressure and easy circulation.

In underfloor heating systems, water distributors and water collectors connect the main water supply pipe to the return pipe. Water dispensers are used to connect heating pipes in water systems**.

The functions of the return water distribution and water collection device are mainly pressurized, depressurized, stabilized and diverted, which are normally pure copper, corrosion-resistant, and stainless steel; But by no means pig iron.

The bathroom can be placed, that is, if you have multiple circuits, your bathroom door may not be large enough, the bathroom can be installed under the basin, and the standard water collector is installed between 50-60cm

It can be installed in the bathroom or in the kitchen.

Where is the appropriate place to install a manifold for underfloor heating? Chengdu Taiyang HVAC will give you a detailed analysis:

The main function of the manifold is to distribute the hot water from the pipeline system to the various rooms that need to be heated through the floor heating coil buried under the floor, so as to achieve the heating effect. So, where is the appropriate place to install the manifold for floor heating?

First of all, the manifold should be installed before starting to lay underfloor heating pipes. When installed horizontally, the general water separator is more suitable for installation, the water collector is installed below, the center distance is 200mm, the center of the water collector should not be less than 300mm from the ground, if installed vertically, the lower end of the water collector should not be less than 150mm from the ground.

Secondly, the location of the manifold should be designed in a place that is easy to control, maintain, and has drainage pipes. Not suitable for installation in bedrooms, living rooms, and even less suitable for installation in storage rooms or cabinets.

Finally, for the semi-over-the-top room, the manifold is suitable for installation at a high or high place, and for the duplex structure house, the manifold is suitable for installation on the corresponding unified main pipe of the upper and lower floors.

Where is the appropriate place to install a manifold for underfloor heating? As long as the above three points are operated, the role of the manifold in floor heating will be played to the fullest.

Floor heating water separator is a very important part of the floor heating system, and the correct installation method can ensure the stability of its performance and the extension of its service life.

This article will detail the correct installation method of a floor heating water divider, as well as the things you need to pay attention to during the installation process.

1.Check the underfloor heating system.

Before you start installing a floor heating manifold, you need to check that the floor heating system is functioning properly. Check that the underfloor heating pipes are unblocked, that the pipe joints are secure, and that the branches are properly connected.

2.Measure the position of the water separator.

The position of the separator needs to be measured before the installation location can be determined. Depending on the size and layout of the room, choose the right location for the water separator. Typically, the water separator is installed in the corner of the kitchen or bathroom, far away from the main water supply pipe.

3.Prepare the installation tool.

Before installing the underfloor heating water separator, you need to prepare the required installation tools, such as drill bits, pliers, pipe cutters, raw meal tape, sealing rings, etc.

1.Assign water pipe diameters.

Before installing the floor heating water separator, it is necessary to determine the diameter of the water inlet and return outlet of the water separator according to the design requirements. Normally, the inlet is 4 pipes and the return port is 6 pipes. If there are special requirements for the old design, the relevant regulations should be observed.

2.Install a water separator.

First, use a pipe cutter to cut the separator pipe. According to the design requirements, the water separator is installed in the designated position and fixed firmly. Make sure that the base of the separator is vertical and well fixed, and check whether the connections are secure.

3.Connect a variety of pipe fittings.

Connect the water inlet of the water separator with the main water supply pipeline, and install the valve; Connect the return port of the water separator with each branch and seal it with raw meal tape; Fix all kinds of pipe fittings on the water separator.

4.Debugging and use.

After the installation is completed, it needs to be debugged and used. Open the main valve and check whether the various branches are connected correctly and whether the water separator is operating normally. If something goes wrong, it needs to be adjusted and fixed in a timely manner.

Clean the water separator.

Before installing the underfloor heating manifold, the water separator needs to be cleaned. Cleaning can remove impurities and dirt in the pipes and improve the use of water separators. After washing, it needs to be rinsed with clean water and dried.

2.It is forbidden to hang items on the water separator.

When installing a floor heating water divider, it is forbidden to hang items on the water divider. This will cause the hanger to fall and affect the operation of the pipeline, and in severe cases, it may lead to damage to the water separator.

3.Exhaust operation must be carried out after installation.

Before the underfloor heating system can be put into service, the pipes need to be vented. This prevents gas from accumulating in the pipeline, affecting the operation and service life of the system. The exhaust operation should be carried out after the installation of the separator is completed.

The correct installation method of the underfloor heating water separator is as follows:

1.Determine the installation location: First of all, you need to determine the installation location of the floor heating water distributor, which is generally on the more central wall. Mark the corresponding position on the wall, and use a flat ruler to ensure that the position is level and flat.

2.Install the water separator bracket: according to the marked position, install the bracket of the water separator on the wall, the bracket is generally made of iron material, which needs to be drilled first, and then the bracket is fixed on the wall with fixing screws.

3.Install the water separator: Place the water separator on the bracket and make sure the water separator is level and secure.

Connect the underfloor heating main in front and back of the water separator and tighten the nuts with a wrench. When installing the water separator, carefully check whether all the connecting parts are tight to ensure that the subsequent operation and use are safe and reliable.

4.Turn on the power supply: Turn on the power supply of the floor heating water divider, and adjust the temperature controller of the water divider, adjust the set temperature of the temperature controller according to the required indoor temperature, and ensure the stability and comfort of the indoor temperature.

In the process of installing the floor heating water separator, it is necessary to pay attention to the safety of the installation site, connection part and power supply to avoid leakage and potential safety hazards. In addition, during operation, the corresponding installation specifications and operation guidelines should be followed, and the appropriate floor heating water separators and accessories should be selected to ensure the quality of installation and the use effect. Consult a professional for advice and assistance if needed.

The correct installation method of the underfloor heating water separator is as follows:

Determine the installation location: Choose a suitable location to install the underfloor heating manifold, usually where the underfloor heating pipes enter the room, such as under the wall or floor.

Prepare installation materials: Prepare the underfloor heating water separator and required mounting accessories, including bolts, nuts, gaskets, etc.

Mounting bracket: Use bolts and nuts to secure the bracket of the underfloor heating water separator in the installation position. Make sure the bracket is firm and stable enough to withstand the heavy lifting of the underfloor heating water divider.

Connect the tubing: According to the design and layout of the underfloor heating system, connect the underfloor heating pipes to the underfloor heating separator with suitable connectors. Make sure the connection is tight and there are no water leaks.

Install the control valve: According to the needs of the underfloor heating system, install a regulating valve to control the water flow and temperature of the underfloor heating water distributor. Install the control valve correctly according to the instructions provided by the manufacturer and make sure it is working properly.

Connect the power supplyTesting and debuggingAfter the installation is completed, the necessary testing and debugging work will be carried out. Check whether the various parts of the floor heating water separator are working properly, ensure that the water flows smoothly and without leakage, and adjust the water flow and temperature.

Install a protective deviceInstall corresponding protection devices for the floor heating water distributor, such as filters and safety valves to prevent scale, so as to prolong the service life of the floor heating system and improve the safety performance.

Please note that during the installation of underfloor heating separators, it is advisable to seek professional help or consultation to ensure that the installation process is safe and reliable, and that it complies with the relevant building codes and standards.