What are the tips for the pasting of tile adhesive?

Tile adhesives are generally divided into ordinary type (model 1), strong type (model 2) and tough type (model 3). Among them, ordinary tile adhesive is generally used for the bonding of a variety of floor tiles or small wall tiles on the ordinary mortar surface; Strong tile adhesive has stronger adhesion than ordinary glue, and has the ability to prevent falling, and is suitable for wall tiles and wood boards with relatively large adhesive requirements; Strong tile adhesive has excellent flexibility, very large adhesion, better than strong type, can effectively prevent the damage of thermal expansion and cold contraction to ceramic tiles, usually used for fiberboard, gypsum board, plywood or old finishes and other bonding. How to use:

Wet construction walls, ground, the inside of the wall and ground must be kept dry, the surface of the wall and ground needs to be kept flat, and the uneven or rough surface can be smoothed with cement mortar; Remove the floating ash, oil and other stains of the base layer, otherwise it will affect the adhesion of the tile adhesive; Adjust the binder, the water-cement ratio is about 1:4, and stir well. The binder should be used up within 5 to 6 hours (when the temperature is relatively high and the light is sufficient, it should be used up in a shorter time); Apply the mixed adhesive to the back of the tile to be laid, press firmly until the tile surface is flat, and the tiles that have been laid in 15 minutes can be corrected by moving.

Use a toothed scraper to apply the glue to the working surface to evenly distribute it and form a toothed pattern (adjust the angle between the scraper and the working surface to control the thickness of the glue). Each coating is about 1 square meter (depending on the weather temperature, the required construction temperature range is 5 40), and then the tile can be kneaded on it within 5 15 minutes (adjustment needs to be carried out within 20 25 minutes); The selection of tooth scraper size should consider the flatness of the working surface and the convex and concave degree of the back of the tile; If the gap on the back of the tile is deep or the stone and tile are large and heavy, double-sided gluing should be carried out, that is, the working surface and the back of the tile are coated with glue at the same time; Pay attention to the retention of expansion joints; After the brick laying is completed, the next step of the caulking process can only be carried out after the mortar is completely dried (about 24 hours). Clean the surface of the tile (and tools) with a damp cloth or sponge before drying. If it has been cured for more than 24 hours, the stains on the surface of the tile can be cleaned with a tile and stone cleaner (do not use acidic cleaners).

Tile adhesive, also known as ceramic tile adhesive, is mainly used for pasting decorative materials such as tiles, face tiles, floor tiles, etc., and is widely used in interior and exterior walls, grounds, bathrooms, kitchens and other building finishing decoration places. Its main characteristics are high bonding strength, water resistance, freeze-thaw resistance, good aging resistance and convenient construction, which is a very ideal bonding material. Tile adhesive, also known as tile adhesive or binder, adhesive and other names, is a new type of material for modern decoration, replacing the traditional cement yellow sand, the adhesive force is several times that of cement mortar, can effectively paste large ceramic tiles and stones, and avoid the risk of falling bricks.

Good flexibility to prevent hollowing in the production of drums. This product is a polymer modified cement-based tile adhesive, which is divided into No. 1 (ordinary type (reinforced) and No. 3 (larger size tile or marble) and other varieties. Tile adhesive contains a variety of additives, specifically the functionality of tile adhesive.

Generally, cellulose ether, which provides water retention and thickening effect, is added to tile adhesives.

As well as to provide latex powder to increase the adhesion of tile adhesive, the most common latex powder is vinyl acetate copolymer, vinyl laurate, ethylene vinyl chloride copolymer, acrylic acid and other additives, the addition of latex powder can greatly increase the flexibility of tile adhesive and improve the role of stress, increase flexibility. In addition, other additives are added to tile adhesives with special functional requirements, such as adding wood fiber to improve the cracking resistance of the mortar and improving the opening time, adding modified starch ether to provide anti-slip performance of the mortar, adding early strength agent to make the tile adhesive improve the strength faster, adding water repellent agent to reduce water absorption rate and provide waterproofing effect.

1. Before paving, the base surface must be treated well to keep the surface clean and tidy. If the base surface is uneven, it should be dealt with in time to prevent the surface from being uneven and affecting the bonding effect of tile adhesive. If the levelness error of the surface is more than 3 mm, it should be leveled with cement mortar, and the loose material and sand and gravel on the surface should also be shoveled to remove the poor branches.

2. Brush the interface agent Then, a layer of interface agent should be painted on the base surface, and the purpose should be to increase the roughness of the base surface and ensure that the tile can be pasted more firmly. After brushing the interface agent, it is best to pre-pave the tiles first, which needs to be pre-paved according to the style on the drawing, and the elastic line treatment should be done on the base surface. If it is a non-whole tile, it should be attached to a hidden place, such as:

corners, under the cabinet, so as not to affect the appearance. 3. Stirring tile adhesive should be adjusted in strict accordance with the proportion, mixing water and powder, and then stirring with a stirrer. Stir until particle-free paste is sufficient.

Do not add cement, sand and gravel when stirring, and then let it stand for a few minutes to allow it to fully mature. It should be noted that it is best to stir for a while before use, and the prepared tile adhesive should be used within 2 hours. 4. Tiling can start to paste tiles next, according to the control line of the base surface of the paving, Qingna first stick the tiles against the wall, from the inside to the outside of the paving.

Then use a scraper to apply the tile glue behind the tile, lay the tile flat, press it flat, and then use a rubber hammer to beat it firmly. 5. After cleaning the tile surface and tiling the paving, the stains on the surface of the tile should be cleaned up in time, especially the tile adhesive, to prevent it from sticking to the surface and affecting the appearance. After 24 hours of paving, caulking should be carried out to prevent the accumulation of stains in the crevices.

As we all know, special glue must be used to paste tiles, so that there will be no falling bricks and other phenomena. So what glue is used to paste tiles? What should I pay attention to when using tile adhesive? Let's take a look!

Tile adhesive, tile adhesive, and colorful caulk can be used to paste tiles. Among them, tile adhesive is characterized by high bonding strength, water resistance, freeze-thaw resistance, and aging resistance. Tile adhesives are characterized by simplifying the process and saving money.

Colorful caulk is characterized by multi-color spring pattern, strong pressure resistance, wear resistance.

What should I pay attention to when using tile adhesive:

1. When using tile adhesive, although there is no need to soak the tile and the ground in water, if you encounter a tile or base layer with strong water absorption, you should soak it in water for a few minutes.

2. The initial strength of tile adhesive is relatively low, and the strength can be reached only about 7 hours after pasting, and the ridge thickness should be avoided within 24 hours to avoid heavy load Sakuramori Town on the surface of the tile.

3. The anti-freeze type in winter can be constructed within -10.

4. The adhesion of tile adhesive to ceramic tiles and base surface is several times that of cement, which can avoid brick dropping.

How to construct tile adhesive:

1. Clean the wall or ground so that the surface is dry, clean, and free of stains.

2. Add water to the tile adhesive and stir it into a paste, then wait for 10 minutes before stirring, remember to use it in about 2 hours, and do not reuse.

3. Use a scraper to apply the glue to the wall, and knead the tiles on it for fifteen minutes. If it needs to be adjusted, it should be adjusted before the tile adhesive is not solidified.

4. Finally, the expansion joint should be retained, and the product should be used in the environment of 5 40, and the product can be stepped into or caulked after 24 hours.

Article summary: Well, about what glue to use for pasting tiles and what to pay attention to in the use of tile adhesive related knowledge is introduced here, friends who need more information, please continue to pay attention to Qeeka Home, we will have better and more exciting content for you in the future.

Tile adhesive stickersIt has many advantages, such as the use of tile adhesive can save more space than the use of cement, and the tile adhesive paste only needs a thin layer, while the cement is thicker; The adhesive stickiness of the tile is strong, if the construction process is up to standard, the tile sticks very firmly; It can also reduce waste, no toxic additives, and meet environmental requirements. Today, let's learn about tile adhesive stickers.

How to use tile adhesive stickers:

1. Tools: home taxi tile adhesive, electric mixer, toothed scraper, sturdy plastic bucket, small shovel knife, level, plastic cross, early glue hammer.

2. Steps: Step 1: First clean the back of the pre-selected tiles and check the pasting base surface.

The base surface should be firm, smooth, clean, no pollution, loose matter, hollow, etc., there are curing agents, release agents, and smoother concrete surfaces need to be polished and rough after construction. If the base surface is not firm and uneven, please use the water core mud mortar to smooth it in advance. Note:

The smoother the wall, the more convenient it is to put tiles behind.

Step 2: Pour the required water into the "mixing bucket" tile adhesive mixing ratio: 20kg tile adhesive + (4-5) kg water.

Step 3: Slowly pour the tile adhesive powder into the "mixing bucket". Tile adhesive mixing ratio:

20kg tile adhesive + (4-5) kg water, note: please do not add any products to the tile adhesive, such as: cement, etc., if you need to enhance the viscosity, you can only use a special tile adhesive reinforcing agent.

Step 4: After pouring water and tile adhesive, then use an "electric mixer" to stir until it is a uniform and particle-free, non-sedimentary paste, let it stand for a few minutes and then stir slightly, and then start to lay tiles below.

Step 5: During construction, please use a professional "toothed scraper" to evenly scrape the glue on the working surface, and scrape about 1 square construction surface each time. Note: There are two commonly used toothed scrapers: 6 cm and 10 cm.

Step 6: Use the "toothed scraper" to evenly scrape the glue on the base surface and the back of the tile and then apply the tiling operation. Note: There is generally dust on the back of the tile, please wipe off the dust when scraping the tile adhesive.

Step 7: Rub the tiles against the base surface by hand or use a glue hammer to adjust the parallelism of the tiles.

Step 8: To ensure the parallelism of the tiles, it is recommended to use a level and a cross for tiling.

Step 9: After the above processes are completed, the cleaning is carried out, and the construction of the stable tiles is completed, and the caulking is completed after 24 hours.

The above is a detailed answer about tile adhesive stickers, I don't know if you are satisfied with our introduction.

In the process of decorating a new house, the glue used in different projects is also different, such as tile paving, once the choice of glue is not suitable, it will lead to the situation that the tile is not firmly paved, so what glue can be used to stick the tile? What are the benefits of tile adhesive? Let's take a look!

First, what glue can be used to stick the tiles.

Tiles can be bonded with a de-acetic acid adhesive, which vulcanizes very quickly and has good transparency, but it is easy to release acetic acid during the curing process and can smell very strong. In addition, an alcohol-free adhesive can be used, which is non-corrosive and has a small curing shrinkage, which is not easy to peel off after immersion in water, but is not easy to bond with tiles that are too smooth.

Second, what are the benefits of tile adhesive.

1. Tile adhesive will not add harmful substances in the production process, and will not produce dust and waste during construction, which is not only environmentally friendly, will not affect the health of construction personnel, but also convenient for construction.

2.The home decoration of the training system is generally the use of cement to pave tiles, not only low adhesion, but also a lot of cement will be consumed in the construction process, but the tile adhesive can save materials during construction, the adhesive layer is thin to only millimeters, and has strong adhesion, which can greatly reduce the use of decoration materials.

3. Tile falling is a very terrible thing, so when paving tiles, we must ensure the adhesion of tiles, tile adhesive has good adhesion, which is two to three times that of cement, which can firmly stick the tiles on the wall to avoid the situation of tiles falling.

Summary: What glue can be used to glue ceramic tiles can be glued to the relevant content is introduced here, I believe that we have a better understanding of the choice of tile glue and hope, I hope to help friends in need. When you buy tile adhesive, you can choose according to your own needs, so that the tile adhesive can achieve better use effect.

1. Tile adhesive can be used. As a new type of material used in modern decoration, it replaces the original traditional tile material cement yellow sand, the viscosity of tile adhesive is several times that of cement mortar, which can effectively paste tiles of various specifications, greatly reducing the risk of falling bricks, and itself has good flexibility, and it can also prevent the tile from pasting the time and space drum.

2. Marble glue can also be used. First of all, the remaining mud on the back of the tile should be cleaned up, and then a layer of marble glue should be applied on the back of the tile, and finally the tile can be pressed on the wall, which does not affect the appearance at the same time, and the adhesion is also very good. This glue itself has the characteristics of heat resistance, water resistance, aging resistance, and is convenient for construction and installation.