How to replace the soft connection pipe of water heater?

You can connect the hot water tank in the water heater with a bucket first and use it elsewhere to avoid waste. Then wait for the water temperature to cool down before using a wrench.

Screw out the outlet pipe and replace it with a new one.

Ordinary quick-heating electric water heater.

Although the volume is similar to that of the dual-mode electric water heater, the internal structure is very different, and the quick-heating electric water heater is only smaller in size and more powerful than the storage electric water heater, so the heating speed is indeed faster than the storage electric water heater.

Water storage type. According to its outlet type, storage type electric water heater can be divided into two types: closed electric water heater and open electric water heater. Closed electric water heaters control the amount of water at the water outlet by one or more valves and work under tap water pressure.

This type of water heater has the advantages of flexible installation position, high outlet pressure and low heat loss. However, because the inner tank works under pressure, it needs to use thicker materials, and the manufacturing process is demanding.

An open electric water heater has an open outlet and a valve on the inlet line controls the amount of water. This type of water heater works at atmospheric pressure, so its inner tank production requirements are low, and the structure is relatively simple. Most of the electric water heaters produced by manufacturers are enclosed electric water heaters.

There is a small plastic cover on the lower part of the silver handle, and this plastic cover can be pried open with a light prie, and then there is a small screw inside, loosen the small screw inside, and the silver handle can be taken out.

When the silver handle is taken out, you can see that there is a plastic circle connected to the large plastic lid labeled cold and hot water, and this plastic circle can be unscrewed and can be unscrewed by hand.

When you unscrew the plastic circle, you can take out the large plastic lid labeled hot and cold water.

After taking out this large plastic, it is very convenient to change any tube.

First, use a tool to unscrew the broken shower hose joint, then connect one end of the hose to the sprinkler head, and the other end to connect the water heater water pipe, the water pipe is tightened with a tool, and there is a round nut fastener where the sprinkler head is connected, just twist the round nut to screw it on, so that the shower hose joint is replaced.

First of all, turn off the inlet water, put all the stored water according to the instructions, and the hexagonal parts at both ends of the hose can be twisted, and it can be replaced by unscrewing.

The hose removal and installation of the shower is relatively simple. If you have an old-fashioned shower hose and showerhead at home, it can be a hassle. The connection of the shower hose to the water heater can be covered with a lid.

You'll need to remove the cover, unscrew the hose, and replace it with a new shower hose. Specifically, it depends on the connection of the water heater shower hose.

The soft connection does not refer to the bellows connection, if so, the bellows can be replaced directly according to the caliber.

Here's how to replace the water heater inlet and outlet hoses:

1.Stop the hot water heater from running: Turn off the power or gas valve of the water heater first, make sure the water heater stops running, and wait for the water heater to cool down.

2.Disconnect the water source: Close the valve of the water inlet pipe and cut off the water source**.

3.Drain water pressure: Open the drain valve of the water heater and drain the water pressure in the water heater. A hot water tap or drain switch can be turned on to allow the water pressure to drop naturally.

4.Remove the hose: Using a wrench or wrench set, easily unscrew the hose connection nut. One end is connected to the water inlet of the water heater and the other end is connected to the water outlet.

5.Install a new hose: Choose a new hose of the right size and type, making sure it matches the caliber of your water heater.

First connect the hose to the water inlet of the water heater, then tighten the nut to make sure the hose is sealed with the water heater connection. Next, connect the hose on the other end to the water heater's outlet and tighten the nut.

6.Check the connections: Make sure the hose is securely connected and there are no water leaks. You can use Na Nai to manually rotate the hose and observe for leaks in the connection.

7.Restore the water supply: Open the valve of the water inlet pipe and restore the water supply.

8.Fill and drain: Open the inlet valve of the water heater, fill the water and remove the air to ensure a stable water flow.

9.Check for water leakage: Check whether there is any leakage at the connection between the water heater and the hose, if water leakage is found, the connection should be re-checked and tightened. Cave orange spring.

Precautions: Always make sure the water heater is off and cooling before replacing the hose.

When replacing hoses, hose connections and valves can be cleaned as needed.

If you are unsure about the operation, consult a professional or the technical support of the water heater manufacturer.

It is best to use a metal hose for the installation of electric water heaters, which has a better high temperature resistance and a better resistance to the metal hose, which is more durable than the hose and is easy to break.

For electric water heaters, the industry now requires the use of PPR pipes to weld its inlet and outlet, on the one hand, it has a long service life and can effectively prevent and control water leakage at the inlet and outlet of the water heater;

On the other hand, it can effectively avoid the frequent jumping of the power switch of the water heater due to secondary grounding, so it is said that it does not meet the safety and installation specifications when connected with metal pipes.

Extended information: Household multi-functional water heaters are usually installed on the kitchen balcony, and the air outlet is linked to the kitchen through the air duct, so that the cold air blown out can directly enter the kitchen to achieve the effect of refrigeration. When installing, you only need to link the hot and cold water outlet with the hot and cold water reserved in the house, and you can use it when you connect it, and the installation is very simple.

Household multi-function buried energy water heaters mostly use microcomputer intelligent controllers, which have a variety of intelligent control functions such as time setting, timing on/off function, water temperature setting, ventilation setting, overheating protection and so on.

However, most of the functions have been set by the manufacturer at the factory, just use the default values, basically only need to set the temperature you need (usually set at 45-50 degrees) to use.

1. First of all, turn off the power supply and outlet valve of the water heater. 2. Unscrew the screws on both sides of the hose, if your strength is enough, you can twist it directly by hand, if the strength is not enough, use a wrench and other tools to unscrew it. 3. Next, connect the new hose between the water heater and the shower head and tighten it.

4. After connecting the hungry skin, open the water outlet valve to see if it will collapse and leak, and make sure that it will not leak and rot, and then connect the power supply.

Summary. Hello Kiss is happy to answer this question for you. 1.

Turn off the power of the water heater, then turn off the inlet and cold water switch of the water heater, and then turn on the drain pipe clockwise to large. 2.Prepare a basin and put it under the sewage outlet, the water storage capacity of the general water heater is about 50L, prepare a few more basins according to the capacity, otherwise it will make the floor sewage flow sideways.

3.Unscrew the drain nut and don't use too much force when screwing, because the drain nut is connected to a magnesium rod, and if the force is too strong, the magnesium rod may be broken into the water heater.

What brand of water heater are you?

Hello Kiss is happy to answer this question for you. 1.Turn off the power of the water heater, then turn off the inlet and cold water switch of the water heater, and then turn on the drain pipe clockwise to large.

2.Prepare a good basin for the hole and put it under the sewage outlet, the storage volume of the general water heater is about 50L, and prepare a few more basins according to the capacity, otherwise it will make the floor sewage flow sideways. 3.

Unscrew the drain nut and don't use too much force when screwing, because the drain nut is connected to a magnesium rod, and if you use too much force, the magnesium rod may be broken into the water heater.

Water heaters are essential household items in our lives, and the installation of water heaters is also something we need to pay great attention to. When installing a water heater, the selection and installation of the white hose is a very important step. Therefore, this article will introduce the installation method of the white hose of the water heater to help you better install the water heater.

1. Choose a white hose.

When choosing a white hose, you need to pay attention to the following points:

1. Pipe: Generally, the materials of white hose are PVC, PE, PP, etc. It is recommended to choose a hose made of PVC, because PVC has better resistance to high temperature and corrosion;

2. Size: The size of the hose needs to be selected according to the size of the water heater outlet pipe and the inlet pipe, and it is recommended that the size be consistent to avoid the situation that the water flow is too small or too large.

3. Quality: It is recommended to choose the best white hose to avoid water leakage or hose aging, causing potential safety hazards.

Second, the hose installation steps.

1. Close the main valve of the water heater

Before installing the white hose, you first need to close the main valve of the water heater to avoid the accident of scalding or leakage when the water heater is energized.

2. Installation hose:

Connect the white hose to the water inlet and outlet of the water heater separately, and pay attention to tighten the hose connection port so that it does not loosen or leak.

3. Check the hose:

Once the installation is complete, the hose needs to be inspected to confirm that there are no loose or leaking hose connections.

4. Open the main valve of the water heater

After checking that the hose is correct, check again whether the main valve of the water heater is closed, and after confirmation, you can open the main valve of the water heater in a respectful state and check whether there is any water leakage.

3. Precautions.

1. Service life: The general service life of the white hose is about 5 years, and it needs to be replaced in time after the expiration date.

2. Plug interface: The plug interface needs to be grounded to avoid leakage.

3. Hose interface: The hose interface should be tightened during installation, and Liangqingyuan should avoid loosening or water leakage.

4. Quality inspection: It is necessary to regularly check the quality of the hose to confirm whether the connection is loose or leaking.

In short, the installation of white hose is an important step in the installation of water heater, if the installation is not done properly or the hose is selected from the wrong material, it will bring unnecessary troubles to our lives, and even cause safety problems. Therefore, it is recommended that when installing a water heater, you must carefully choose and install a white hose.

Water heater installation.

1.After the gas valve is installed, the master must first measure it, and only then make an eye on the wall according to the measured data. The storage water heater must be installed on the load-bearing wall, otherwise there are potential safety hazards, if it has to be installed on the light wall, it must be installed below the bracket or other treatment.

2.Start work below, there is also a skill in drilling on the tile, you must first use a fine drill bit to grind a small hole to fix the hole position, and then use a thick drill bit to slowly grind the tile through with a slow gear, and then use the impact gear to drill the hole deeply, so that the general tile will not crack.

3.Drill a dozen, fix the screws, and the next thing is to hang up the gas water heater. At the same time, it is necessary to ensure that the water heater is firm and not loose. The installation height is generally 165 175 cm, and the fire window is parallel to the person's line of sight.

4.After fixing the water heater, it is necessary to fix its hot and cold triangle valves. It should be noted that the outlet pipe (hot water) should not be equipped with a valve, otherwise it will affect the water output and affect the use function.

5.At the same time, don't ignore the installation of small details, the installation of exhaust pipes and threaded pipes is equally important. The exhaust gas exhaust hole of the water heater should be opened separately, and the public exhaust hole should not be used.

6.The next step is to choose the right water pipe to connect the reserved cold water pipe with the water heater, generally you can use a special metal hose, and it is best to choose a water pipe that is not easy to age.

7.After the installation is completed, the overall test should be carried out, and the gas should be turned on, the electricity should be turned on, and the test should be carried out to test the heating function of the water heater and whether the water pipe is leaking.

You can add a ball valve (switch) to the hot water pipe and cold water pipe near the tap, and you can use these two switches as a mixing valve for hot and cold water. Note: There are 4 pipes and 6 pipes in the water pipe, and when you buy a switch, you should buy it according to the pipe model in your home, and the general faucet is 4 points.

Water heater outlet - hose - triangle valve - hard pipe or tee --- hard pipe - triangle valve (or faucet) - hose --- spray.

It's simple, with matching fittings. If it is a PPR pipe, use a fuser.

It's not very simple, haven't you already said it?

Bold go-to.

Simply teach you a simple way, go to the neighbor's house and see what's going on.