How to install the rod throwing fish float 5, how to install the rod throwing fish float

The casting line is wrapped around the fishing reel, and then connected to the hook through the wire loop, the hook is generally used as a string hook or ** hook, which is bought ready-made, and can be bought in the fishing tackle store, which is very cheap. Casting the rod generally does not need to float, and a small bell is clamped on the rod slightly to indicate the fish signal.

1. The emergence of the rod throwing abandons the limitations of hand rod fishing, so that the angler extends his arm, throws far and fishes big, can be near or far, and the fishing point is arbitrary.

2. The length of the fishing line of the cast rod can reach hundreds of meters, and it can be retracted and released freely, even if it encounters a huge tension that the rod line can not bear, the force relief device can also effectively improve the bearing capacity of the hook line through the perfect function, even if the fish is difficult to escape.

3. Casting the rod to fish has changed the shackles of the hand rod and fishing rod, so that the angler's hands can be freed, and he can sit or lie down, which reflects the elegance of leisure and entertainment.

4. The wind resistance of the casting rod is good, and it is encountered when fishing.

Fourth- and fifth-level gales can also be fished. In natural waters with a low density of fish, it is possible to pass"Widely sown and harvest thinly"ways to improve catches.

5. In the middle of summer, you can take advantage of the length of the line, put the fishing line long, and place the rod under the shade tree to avoid the exposure of the scorching sun. People with weak eyesight do not need to look at the mark, as long as they sit quietly in front of the rod and pay a little attention to the tip of the rod in front of them, they can be competent to cast the rod for fishing.

It's a little longer. If there is a bright bar next to it, it determines the strength of the toss.

I don't know what kind of environment you're going to fish in, sea fishing or river fishing.

It is recommended that you buy automatic float which is versatile and hassle-free.

How to install a fish float and a hook on a sea rod

Hooks, lines, and scissors should be prepared before installing them. Cross the ends of the thread together, put the hook on, the hook handle forward, slowly wrap 4-7 times from the hook handle forward, and slowly pull out one end of the thread, so that the hook is tied.

Install the fish float

1. When the air fishing is not at the end, the lead skin can be adjusted to make half of the total number of floats exposed, taking 12 mesh floats as an example, and 6 meshes can be exposed.

2. To find the bottom of the double hook bait, you need to adjust the height of the float, which is more than half of the total number of floats exposed, that is, more than 6 meshes on the surface of the water, which means that the double hook has been in the end.

3. Double hook bait, you need to adjust the height of the float, to expose the water surface 3 mesh is appropriate, then you can fish the double hook at the bottom of the water state for a hook lying horizontally and a hook lightly touch the bottom, belongs to a more sensitive state If you want to continue to improve sensitivity, you should reduce the number of floats exposed to the water surface, if you want to fish blunt, you should increase the number of floats exposed to the water surface.

The installation and use tutorial of the rod throwing is as follows:

How to install the throwing rod].

One of the first steps when using this type of rod is to assemble it. Generally speaking, they are composed of small subsections, and when assembling, you need to stretch them apart and then assemble them. There are also some auxiliary tools, such as reels, etc., which need to be mounted on the casting rod.

[How to use the throwing rod].

1. First of all, pull out the throwing rod section by section, so that all the coils can be aligned and in a line, and the joints of each section need to be tightened with greater force.

2. Install the reel wheel, install the reel on the card base, fix the reel with a nut, and dial the reel check switch to the reverse position.

3. Pull out the fishing line, thread it through the coil one by one, until the tip of the rod, and then hang the aconite and bomb bait with the connecting loop.

4. Turn the check switch back to the forward rotation position, and be sure to debug the drag device, not too tight, not too loose.

5. First, turn the reel slightly, and the bait ball should be about 40 cm away from the tip of the rod, and then hold the rod at the reel with your right hand.

6. Clamp the middle finger and ring finger on the back of the reel, hook the fishing line with the first joint of the index finger, flip the line loop, and cast the bait hook to the fishing point according to the familiar throwing method.

Tips for picking a throwing rod:

1. When choosing a high-quality, sturdy and durable casting rod, you should first consider its use, whether you want to catch big fish or small fish, or both.

2. If you go to natural waters to catch big fish, you can choose a hard-tuned long rod. The rod is long and has a large fishing power, throws far, and is convenient for walking fish, and the thick fishing rod can resist the impact of big fish. The weakness is that the throwing is laborious, and it is not suitable for those with poor physical strength. The rod is hard and easy to hurt the main line of the fishing rig, and it is easy to break the line if it is not operated properly.

3. If you fish for small fish, you can choose a short rod with a soft tone below the meter. The short rod has loose requirements for the fishing position, especially in the environment where there are obstacles such as trees and rocks around the fishing position.

4. The rod is light and effortless to use, and the thin rod tip can amplify the signal of the hook in the small fish, and it is not easy to hurt the main line. The disadvantage is that the rod is soft, and it is often passive and time-consuming when walking the fish.

5. If you choose a casting rod that takes into account both, you can choose a rod with medium and hard tonality, which can not only resist the impact of big fish, but also amplify the signal of the hook of small fish. It has a larger range of use than the above two rods. Medium hard casting rods are mostly used in polyculture fish ponds.

The float is installed on the fishing line in the following ways:

1. Vertical float, also known as platform fishing float, refers to a fishing tool that transmits the information that the fish swallows the bait and indicates the location of the bait. From the structural point of view, the float is divided into three parts: drifting feet, drifting body and drifting tail. In terms of material, there are mainly balshan floats, reed floats, feather floats and nano floats.

The steps to load a vertical float onto the line are as follows:

1. Penetrate two space beans on the main line;

2. Then wear a drifting seat, pay attention to the size of the floating feet, not too big or too small;

3. After penetrating the drift seat, two space beans are installed below to lock the drift seat;

4. Then wear it into the lead seat and tie it to the figure-eight ring;

5. Insert the floating foot into the floating seat to complete the connection between the floating and the main line.

Second, the spherical float is gentle, also known as the sea rod ball drift, generally ABS material, from the structural point of view, the float is mainly divided into drifting tail, drifting belly and drifting tip, the drifting tip part has a round hole, this reserved round hole is used to connect the main line. The steps to load the spherical float onto the line are as follows:

1. Different from the hand rod, the spherical float generally does not use a float seat, but uses a connector to connect the main line with the float;

2. The installation steps are similar to those of the vertical float, and two space beans are added before and after to fix the sea rod connector on the main line;

3. Insert the other end of the connector into the reserved hole of the drift tip and lock it to complete the installation of the spherical float.

The whole process of casting rods and loading lines and fish drifting is like silver

First of all, you must prepare the fishing rod, fishing line, space beans and other tools, and then fold a section of the fishing line in half and thread it into a space bean, knotting the top and bottom, and the knot needs to be tightened when the knot is loose. Then fold a circle in the middle, thread the thread at one end into the other end, pull it tight, then move the space bean up, and finally fix the knot. When tying, pay attention to the knots, the knots should not be too loose, they need to be tighter.

How to install a line for a fishing rod

The fishing rod is the main tool when it comes to fishing, and it can also be said to be the most important tool. After choosing the right fishing rod, the next important task is to attach the fishing line to the fishing rod.

In other words, the right line needs to be prepared first. The most commonly used fishing line is nylon line, pay attention to choose the appropriate model according to the fish and water conditions. Once you have all the tools in place, it's time to start the installation.

First, fold a section of the line in half and thread a space bean into it. A knot needs to be tied above and below it.

Sometimes, these two knots are not particularly tight and relatively loose, at this time you need to tighten these two knots and not be too loose. Then, between these two tied knots, a loop needs to be folded. The double wires at both ends need to be fronted or handled, and the double wires at one end are sandwiched into the other end, and they also need to be tightened.

At this time, the position of the space bean also needs to change and needs to be moved up. Finally, just fix the knots.

How to load a fishing rod with a float

The process of attaching the fishing rod has been described above, and the process of loading the float is also required. First of all, you also need to prepare the right fishing rod, calendar and float. Fishing line is also an indispensable tool at this time.

Install a space bean first, then install a drifter, and then install a space bean.

One of them is used to fix the drift seat, and the other is to adjust the water depth. Let the two space beans clamp the drift seat in the middle and let it be secured.

On the top of the float, there is a hole that needs to be used to install the float. Rinse the prepared fish in this hole. Then, you need to install another space bean, and this space bean can be matched with the two previously installed, so that the float can be fixed better.

After installing the float and making all kinds of preparations, you can basically start fishing.

Fishing rod float installation method:

1. How to choose the float of the fishing rod.

In the process of fishing, many tools are used, including rods, lines, floats, etc. Floats are one of the most important tools, and in many cases they need to be prepared and adjusted in the right way so that they can give a clear signal when the fish is hooked, and the angler can lift the rod at the right time. It can be seen that the choice of float is a very important issue.

When choosing floating, the first thing to pay attention to is the material, often used materials such as reeds, the signals they send are more accurate, and it itself is more affordable.

You should also pay attention to the shape of the float, which can be selected according to the conditions of the water. For example, one advantage of long body drifting is that they are very stable and can be used when fishing the bottom;

The advantage of short floats is that they are more sensitive and can be used when fishing floats. Another problem is the amount of lead eaten, which is related to water conditions and fish conditions. In the case of fishing for big fish or strong wind and waves, it is recommended to use a drift with a large amount of lead.

Second, how to install the float of the fishing rod.

As mentioned above, since floats play an important role in the fishing process, it is important to choose them. Once you've chosen it, you need to attach it to the rod in the right way to use it when you're fishing. Since the float is mounted on the float, the first step is to attach the float to the line of the rod.

Load a space bean on the fishing line, set the drift seat, and then load a space bean. Two space beans can clamp the drift seat in the middle. One of the space beans is used to fix the drift seat, and the other is used to facilitate the adjustment of water depth.

After installing the float on the line, the float needs to be mounted on the float. This is more convenient. Because there are generally two obvious holes on the float seat, one of the holes in the middle is used to install the float, and the other is used to tie the float to the fishing rod with the help of the main line.

After the float is installed, it is also necessary to add a space bean, so that the float can be fixed better, and the state of the float can be adjusted at any time to make the fishing effect better.

Fishing line: The fishing line is divided into main line and subline. The main line is slightly connected to the rod, the main line is folded in half, the end is made into a fishing coil, the fingers are stretched into it, and the two ends are pressed with two fingers and then kicked, the fishing line is pulled out to form a slipknot, and the rod is slightly stretched into the slipknot.

The sub-line is connected to the main line by a figure-of-eight ring.

Fish Drift: Penetrate a space bean on the main line, and then enter the drift seat, Kai Huihuan then uses a space bean to fix the drift seat to stare at the sedan car, and finally the fish drift is stuck on the drift seat.

The rod, line, and float type are all determined according to the size of the fish and the environmental conditions. If the water area is particularly large, and when fishing large fish and fishing far, long rods are used, such as more than meters, small fish, and short rods, such as those below meters. Catch big fish and strong fish with thick lines, such as a line of size 2 or more.

The strong horse line is suitable for catching big fish, which is relatively strong and not easy to break. Fishing for small fish is used to eat a float with a lead amount of less than 1 gram, and for medium-sized fish is about 2 grams. When fishing for big fish, the number of meshes is larger, and the number of meshes is also larger when the wind is large.