How to deal with the arch of the decoration floor tiles

This is some of the information I found on the Wuhan Home Improvement ** Internet, if you still have some questions about decoration, you can check it, you should be able to find out what you need to know. The following is for reference only:

First, if the floor tiles are all arched, one by one can be taken down by hand, then write each brick with a number - so that it is convenient to remember the original position, keep the original direction of the floor tiles unchanged - and then scrape off all the cement mortar stuck to the side of the tiles.

The cement mortar on the bottom surface of the original surface is wiped clean with a dry rag, and then the bottom surface is coated with white glue for carpentry, and then compacted according to the number. To repair a square meter of floor tiles, it is about a pound of white glue.

Second, if only part of the arch up, there are some floor tiles that can be taken down directly, and some can not be taken down, and the floor tiles that cannot be taken can not be pryed, and the hard pry floor tiles are broken, which is more troublesome and requires a cutting machine.

The cutting machine cuts along the floor tile joint, a brick has four sides, and several need to be cut depending on the specific situation, some are afraid that all four sides will be cut, and some can cut two sides.

After cutting, it usually takes an hour or two for the arched floor tiles to collapse naturally. There is a lot of dust when cutting, and you need to constantly add water to the cutter.

That's because it wasn't paved in the first place, right? Or has it been 10 years since the bricks were laid?

It's unlikely that the floor will be tiled in a short time, right?

If it's really up, the new bricks can be repaired, the old bricks are not easy to find, and they can only be re-paved, if you still need any help, you can directly add the love design group 6308 Yimei decorative design 0634

Have the floor tiles been soaked in water during renovation? It should be soaked for 5 hours, and the cement should be evenly coated when sticking to the floor. It depends on how long it takes, and if it's short, you can go to the owner who sells the flooring and the master who sticks the floor.

Don't tell her because she's rude.

Summary. 1. In the cold winter, the floor tiles shrink, or in a humid environment, the tiles are very easy to warp. In the process of laying tiles, the cement mortar is not mixed according to strict proportions, resulting in imbalance of proportions.

If one of the cement and sand is put in more, after using it for a long time, the cement mortar loses its viscosity and produces a certain gap with the tile, which is easy to upturn. 2. Caused by poor quality of ceramic tiles, when we buy ceramic tiles, we can buy them in the large building materials market and consider first-line brands to buy. The quality is more guaranteed, and at the same time, it also reduces the occurrence of after-sales problems.

3. During the laying process, the gap reserved between the tiles is relatively small, and the temperature is relatively high when the indoor temperature changes, especially when the floor heating is turned on. If the gap between the tiles is too small, the tiles are heated or cold, and there is no space to expand and contract, and the tiles are easy to warp. In particular, the temperature difference in the north is relatively large, which is very easy to occur, and the south is relatively rare, due to the relatively large humidity.

Floor tile arch up handling tricks.

1. In the cold winter, the floor tiles shrink, or in a humid environment, the tiles are very easy to warp. In the process of laying tiles, the cement mortar is not mixed according to strict proportions, resulting in imbalance of proportions. If one of the cement and sand is put in more, after using it for a long time, the cement mortar loses its viscosity and produces a certain gap with the tile, which is easy to upturn.

2. Caused by poor quality of ceramic tiles, when we buy ceramic tiles, we can buy them in the large building materials market and consider first-line brands to buy. The quality is more guaranteed, and at the same time, it also reduces the occurrence of after-sales problems. 3. During the laying process, the gap reserved between the tiles is relatively small, and the temperature is relatively high when the indoor temperature changes, especially when the floor heating is turned on.

If the gap between the tiles is too small, the tiles are heated or cold, and there is no space to expand and contract, and the tiles are easy to warp. In particular, the temperature difference in the north is relatively large, which is very easy to occur, and the south is relatively rare, due to the relatively large humidity.

Second, how to solve the problem of floor tiles warping? 1. The general arching solution is only part of the arching of the floor tiles in the general home, if it is not particularly serious, then you can find a suitable time to take it down for replacement, if you can't take it off directly, you can intercept it by using a cutting machine, pay attention to the fact that there will be a lot of dust when cutting, you can add a certain amount of water to the cutting machine. 2. All arching solutions: If all the floor tiles at home are arched, we must take them down one by one, and then write the logo on the floor tiles in each space, and deal with the flatness of the ground directly with tile adhesive.

<> partial or small part of the arch, the floor tiles can be removed at a suitable time. If it is difficult to take, you can use a cutting machine to cut. If all the floor tiles are arched, we need to remove all the tiles one by one, and then correct the flatness of the ground, and then use tile adhesive to paste it again.

1. Check the floor tiles in the entire store or room to see whether individual tiles are arched or large-area arched. When inspecting, you can use to tap the tile, if the sound is empty, it is already hollow, that is, the tile has been separated from the cement layer. Such tiles can easily crack if they are barely pressed down.

Therefore, it is necessary to pry up the arched tiles, re-pavement, and if there are a large number of hollow tiles, they should simply be re-paved in their entirety.

2. First cut the joints between the arched tiles and other tiles with a cutting machine (there will be a lot of dust when cutting, so you need to keep adding water to the cutting machine), and you should lift the tiles very carefully, and the action must be light, otherwise it is easy to cause the tile to crack.

3. Scrape off all the cement mortar stuck to the edge of the tile. Treat the cement layer under the bricks, plane off 1-2 cm and clean it up.

3. Floor tiles: 1:2 - 3, the cement number of cement is cement.

In addition, if white cement is used, be sure to use 108 glue, which can make the cement and floor tiles tightly bonded.

5. Re-pave and flatten the cleaned tiles, and then use a caulking machine to reinforce the cement after the cement is completely dry, so as to avoid the phenomenon of upturned and cracking of the floor tiles.

The floor tiles arched up the way of restoration:

1. Check whether the arching of the floor tiles is an individual floor tile or a large area of floor tiles. If the sound is hollow, it means that the tile has been separated from the cement layer. At this time, if you press the floor tiles down, it is very likely to crack.

If a small area of floor tiles can be pried up and re-paved, but if the number of hollow tiles is relatively large, it can only be re-paved as a whole.

2. Cut the arched tiles with a cutter. A lot of dust will be generated when cutting, so add water to the cutter, and then carefully lift the tile, otherwise it is easy to cause the tile to crack.

3. Then scrape off all the cement mortar stuck to the edge of the tile. Then deal with the cement layer under the bricks, about 1-2 cm off, and clean it.

<>5. Re-pave the floor tiles, and reinforce them with caulk when the cement is dry, which can well prevent the floor tiles from being upturned and cracked again.