Why does an inflatable bed leak slowly? To inflate in one to two or three days, please professional,

When your previous motor burned, find out the cause? Your air compressor should be a reciprocating piston machine. The main reasons for slow piston machine inflation are as follows:

1) The air compressor is used for too long or the lack of oil causes poor lubrication and excessive wear, so that the fitting gap between the piston ring, the piston and the cylinder is too large, and the air compressor shows noise and abnormal vibration, and a little oil splashes out from the oil filling hole and the breathing valve. The body and motor are also prone to overheating. I guess that's the kind of problem with your machine.

2) The use environment of the air compressor is harsh, which makes the carbon pollution of the suction valve and exhaust valve of the air compressor, which causes the valve to be not tightly sealed when working.

When the inflatable bed is first used, it takes a day or two to replenish some air! Because the inflatable product starts to stretch! If you want to make up some air after using it for a period of time or a day or two, it should be a leak in that place!

The definition of an inflatable bed is that it is normal to replenish some gas for ten days! If you need to make up some air in a day or two, there should be a leak in that place! Whether it is a quality problem depends on where the air leak is!

The method we use to check that the inflatable bed is there for air leaks! Fill up the inflatable bed a little and listen carefully in the quiet! Another common way is to wipe it with soapy water and see if there are bubbles there!

It is recommended to find out the air leakage and then see if it is a quality problem or a human problem! I hope it helps!

Air leakage of inflatable mattresses is mainly due to product wear, and after long-term use, there will be some invisible air leakage, which is a normal phenomenon; If there are a lot of air leaks, you can refill the air.

In addition, because the inflatable mattress is made of PVC material, if it is pierced by sharp metal, or if a hot object is approached, the inflatable mattress may break, resulting in air leakage.

Expand your knowledge:

Are inflatable mattresses prone to air leakage?

The air mattress is made of PVC material, which is very flexible and suitable for inflatable products.

How to make up for air leakage on an inflatable mattress

If an inflatable mattress is punctured or burned, you can take steps to repair it

1. Repair the poor needle eye pants.

The inflatable bed is accidentally pricked with one or more small needle holes by a needle or wooden thorn, which is relatively easy to repair

1) Cover the air valve after deflating the bed to reduce the flow of gas in the bed.

2) Take out the glue from the repair kit and drop a drop of glue on the eye of the needle.

3) If the eye of the needle is large, take a toothpick, use the tip of the toothpick to dispense glue, apply it into the broken eye of the needle, and then use glue to coat the hole of the needle.

4) After the repair is completed, wait for four hours before inflating.

2. Repair scratches or burns.

If the inflatable mattress is cut by a knife or burned by fire and has a large hole, it can be repaired according to the following methods:

1) Cover the air valve after deflating the bed to reduce the flow of gas in the bed.

2) Find the patch material in the repair kit and cut a piece of it, which should be enough to cover the crack.

3) Apply glue to the damaged area, press the patch, and glue the edge seams of the patch.

4) Apply pressure to ensure that there are no gaps in the glue surface, and press it firmly with a smooth, heavy object.

5) Wait for eight hours before inflating and the repair is complete.

3. Suede repair.

1) Carefully clean the patched area, after drying, take out the patch and cut it, cover it on the damaged surface, and allow a little more around.

2) Apply a layer of glue to the patch and damaged surface, and glue the edge seams of the patch to ensure a thorough seal.

3) Press it firmly with a smooth, heavy object, press it until 24 hours later, and then inflate it, and the repair is completed.

If the inflatable mattress is damaged in a large area, it can be sent to the seller for repair within the scope of the manufacturer's repair; If it is beyond the scope of repair, it can only be scrapped.

It's almost enough! Don't too much!

First, how to make up for the air leakage of the air cushion bed - find the air leakage point.

I have heard of the medical term of prescribing the right medicine, how to make up for the leakage of the air cushion bed, we first have to find the air leakage point, how to find the air leakage point? Generally, you can test it in three ways, the first is the best if you have a swimming pool at home, you can choose to throw the air mattress into the swimming pool, see where the bubbling ** must be leaking, method two, you can fill the bathtub with water, a small amount of inflation, part of the inspection, see **bubbling is**air leakage, if there is no bathtub and no swimming pool at home, we can use the last test method, the inflatable mattress is coated with soapy water or laundry detergent water.

Second, how to make up for the air leakage of the air cushion bed - judge the material.

Any item has its own unique physical properties, some materials are more special, such as gasoline and plastic will form a corrosive effect, we must pay attention to the material before making modifications. Inflatable mattresses are made of a variety of different materials, the most common are PVC material and vegetable velvet, the properties of these two materials are different, so the repair method is also different. How to make up for the air leakage of the air mattress bed, the second step is to determine what material the air mattress is made of.