What are the precautions for toilets when decorating water and electricity?

Hair dryer socket, small kitchen treasure socket, automatic washing machine socket, bathroom mirror front lamp socket, smart toilet socket, integrated bath bomb power supply, lighting fixture power supply, exhaust fan power supply, floor heating water separator power supply, razor sonic electric toothbrush power supply. 2.It is best to have an outlet in front of or inside the bathroom cabinet, which can be used as a battery charging power source for sonic electric toothbrushes and razors.

Smart toilet power supply, try to choose a part far away from the shower, to avoid the middle and late stage of the resurgence of electricity, <>

You must buy a socket with a waterproof switchIf the floor heating water distributor is prepared in advance and put it in the bathroom, it is best to leave a power supply to avoid the middle and late stage of the floor heating is not hot, you must add a circulating water pump, and there is no power supply. It is best to leave a mop pool water part independently, soak your feet, and mop it is more convenient, you can't use the water under the shower, the water under the shower is relatively high, and it is very easy to splash. If you want to install a squatting toilet toilet, you must stabilize the drainage and water supply in the early stage, and fully consider the road surface that must be raised.

After the hydropower project is done, take pictures to avoid inconvenient installation and maintenance in the middle and later stages.

House decoration is an intricate engineering project, because there is a lot of food in each of its functional area design schemes, and there are a wide range of situations that should be paid attention to, so many people will look forward to the next two years after the interior decoration comes out, because it is too spiritual and too expensive. Renovation of water and electricity in the toilet is an inevitable engineering project, because in the toilet, not only electricity is used to illuminate lamps, baths, natural ventilation exhaust pipes, but also tap water is needed to shower, wash objects and flush toilets, <>

Therefore, in the case of toilet decoration and water and electricity transformation, there are more matters that need to be paid attention to. The toilet water and electricity project cannot be ignored, the toilet is often more wet and cold, and prone to the hidden danger of short circuit! First of all, the power circuit waterway must go to the top of the line, which avoids the wet and cold situation of the power circuit on the ground, greatly increases the service life of the cable, and the waterway line goes to the top, which can also be preventedThe pipes are buried under the wooden floor and leak downstairs!

Caused financial losses! Hydropower projects are carried out to take more photographs, prevent the installation of water heaters in the middle and late stages, small pendants, bathroom mirrors! Punch into the pipe

1. Construction according to the drawings. The decoration needs to be designed in advance, and the construction is carried out according to the design drawings, and the bathroom hydropower renovation is the same, and the drawings will be designed and drawn before the formal renovation construction, so the subsequent hydropower transformation can be carried out according to the previous design drawings of the bathroom according to the drawing positioning construction, without the on-site design of the pipeline direction, so as to simplify the construction.

2. Pipeline sealing. Whether it is the water point pipeline or the sewer pipeline in the bathroom, it is necessary to carry out effective sealing and installation construction, so as to completely achieve the problem of insect and odor prevention.

3. Depending on the facility. The renovation of the waterway of the toilet needs to be determined according to the facilities and equipment of the bathroom, such as toilets, washbasins, mop sinks, women's toilets, water heaters, solar energy, showers, bathtubs, washing machines, etc.

Reasonably lay out the number and location of sockets, plan the location of electrical appliances, and avoid the trouble of using electricity for electrical appliances in the later stage;

Sockets need to be kept at a safe distance from rain to avoid the risk of electric shock.

We must do a good job of waterproof layer, we must pass the waterproof inspection, we must paste the tiles, the way of water and electricity transformation must be correct, and the electricity in the bathroom must do a good job of safety measures.

When the toilet is decorating water and electricity, the method of waterproofing the problem: the ground is solved, and the ground must be leveled before the waterproof is solved. If the ground is not leveled, it may endanger the actual effect of waterproofing, and it may also cause cracking and leakage due to the uneven thickness of the waterproof architectural coating.

Junctions of floor drains, corners, pipes, etc. It should be coated with high elasticity soft waterproofing, because the joints between the wall and the floor of the bathroom will move, and it is most likely to leak.

Check the area where the floor drain was originally drained to see if it has the lowest value. If the floor drain is higher than the gate, it is necessary to lower the floor drain to facilitate the flow of water in the middle and late stages. To put it simply, the lower the floor drain and the thinner the wall thickness of the floor tiles, the higher the height of all bathrooms.

The purpose of the slope is to minimize the flow of water on the toilet floor. However, some construction units evade responsibility. At this stage, there is no slope, and it is necessary to rely on the next process to cut bricks and cut bricks to make slopes.

Therefore, everyone should remember that after the hydropower project is sound, the slope of the ground must be done with mixed mortar and then waterproof.

The method of bathroom construction is at least twice, and you must wait for the paint on the wall to be done before painting. In the case of drawing, remember to brush in the same direction. The main thing is not to miss the brush, especially in the corners.

You should be careful to brush with a brush in a timely manner. Attention should also be paid to the height of the waterproof architectural coating for the walls. The shower area should be at least 30 meters long, and no other places should be less than 30 cm.

After the protective layer is dried, the protective layer must be paved on the surface layer to avoid the waterproof layer being destroyed by the construction of the project later.

Pay attention to the protective layer must be thoroughly covered with the waterproof layer to ensure that it is firmly integrated with the bottom layer and cannot be ignored. And there are no cracks, bubbles, peeling, etc. After the construction of the waterproof project of the toilet is completed, the most important step is the irrigation test, which is also the most important step to check whether the construction of the waterproof project is qualified and whether there is water leakage.

The toilet is filled with water 24 hours a day. If there is no water leakage under the floor, it means that the construction of the waterproof project is qualified and the next project can be carried out.

Be sure to keep the wall and ground flat, and then you need to brush the waterproof coating, at least three times, and be sure to pay attention to the height, so as to do a better job of waterproofing.

It is necessary to choose the right waterproof material to apply and use the right tile, so that the waterproof treatment can be better.

When the toilet is renovated, the most important thing is to solve the problem of water and electricity, so before the decoration of the new house, the water and electricity must be changed, which is very important, so as not to leave potential safety hazards in the later use process.

Plan your size: avoid clashes. The area of the bathroom is small, and after installing the wash basin, toilet and shower room, the remaining exposed wall area is not much, so the socket in the bathroom must be planned to avoid the situation that the toilet or wash basin is against the socket, resulting in the embarrassment that the socket can not be used.

Circuit to ceiling: avoid electric shock. The bathroom is a bathroom function space, the ground is very wet, if the circuit pipe goes to the ground, I am worried that the line pipe will break, and the line pipe will be flooded after living for a long time; In addition, the bathroom is generally made of suspended ceilings, so it is highly recommended to go to the ceiling for the circuit of the bathroom.

Toilet socket: left water and right electricity. The area of the bathroom is small, but there is water and electricity, so when designing and arranging the circuit and the waterway, it is necessary to achieve the separation of water and electricity, such as the power socket and water inlet pipe of the smart toilet, it is recommended to distribute the angle valve and socket on both sides of the toilet, which is generally the layout scheme of left water and right electricity.

The bathroom is the most frequently used space, but although the bathroom is small, if you are not careful, it will affect the convenience of life in the future. So, how to perfect the design of bathroom decoration waterways and circuits? Today, Wenxiang will tell you about the design of toilet water and electricity.

Waterway: 1. A faucet for washing machines.

2. A faucet for the mop pool (it is best to set aside a faucet to clean the mop without a mop pool).

3. Leave the water inlet and outlet of the water heater.

4. A toilet interface.

5. There are two hot and cold water outlets in the washbasin.

6. Two drains: one for the washing machine and one for the shower.

Circuit: 1. It is best to leave a socket behind the toilet (it is convenient to install the clean treasure in the future, and if you don't use it first, you can ask the electrician to wrap the wire and buckle a panel).

2. There is also a socket switch on the right side of the washbasin (a switch that can blow the air after taking a shower and control the mirror headlight).

3. The socket of the washing machine.

The switch of the main light and exhaust fan in the bathroom is generally outside the door of the bathroom; The line is generally walked on the ceiling. )

Bathroom decoration precautions:

1. Angle valves should be installed on the washbasin and toilet water pipes to facilitate future maintenance.

2. When installing other bathroom products, pay attention to avoid the water pipes and circuits on the wall, remember! It is advisable to consult the water circuit archive beforehand**.

3. When workers install exhaust fans, pay attention to whether they install ventilation pipes and seals (some workers are lazy to save this step, and your home will smell every day in the future.) )

4. The power switch should be equipped with a waterproof box.

5. After the pipeline is completed, the pressure test should be carried out, and then the waterproof treatment should be done.

6. After the floor drain is installed, the flushing test should be carried out quickly. (Cement will fall into the sewer pipe during worker installation!) After a long time, it will be damp and solidify! In this way, it is impossible to go into the water. ）

7. If the washing machine is reluctantly installed in the bathroom, you can consider installing it in the balcony kitchen and small hall, which can also extend the life of the washing machine. (The premise is that there is water supply and power supply.) )

8. The floor drain should be opened often to clean up the hair and other debris inside, and then put some water inside! Prevent aftertaste!

9. There should be a threshold stone at the door of the bathroom! Be careful to seal the underneath! Otherwise, if you lay the floor outside, the floor will be damaged by blisters.

10. Pay attention to the lights in the bathroom! It is best to choose anti-fog and waterproof energy-saving lamps with cold light sources (features: safe and power-saving).

11. You can change the single faucet of the washing machine to a mixed faucet! In this case, there will be hot water for washing clothes!

12. It is also important to choose exhaust! The power should be high, the sound should be low, and the wind should not be reversed.

The above is the bathroom decoration water and electricity design plan and precautions, of course, each home is different for each house, although the experience is suitable for the general family, but it is still necessary to design according to the actual situation of their own home!

Bathroom feng shui dead hole 1: The direction of the toilet should not be consistent with the direction of the residence.

According to the requirements of traditional Chinese residential feng shui customs, the direction of the toilet should not be the same as the direction of the house. For example, if the door of the house faces south, when a person sits on the toilet, if the face is south, it is a taboo that the toilet is in the same direction as the house, which may cause health problems in family members. The solution is to adjust the orientation of the toilet to deviate from or reverse the direction of the house.

Bathroom feng shui dead hole 2: Bathroom facilities should not be irregularly shaped.

The choice of bathroom facilities is very particular, the shape of the bathtub is rectangular or round, and regular pentagons and hexagons can also be used, but do not use triangles or irregular shapes, which are not good for users. The bathtub should not be too big, and it should be practical, which is something that should be carefully considered before buying.

Bathroom feng shui dead hole 3: bathroom lamp joints should not be exposed.

The bathroom is damp, so be extra careful when installing lights and wires. Lamps and switches should be safeguarded, and connectors and sockets should not be exposed. If the switch is a rocker type, it should be located outside the bathroom door, otherwise a moisture-proof and waterproof panel should be used to prevent accidents caused by moisture and leakage.

Bathroom Feng Shui Death Hole 4: The bathroom should not be cluttered.

Clutter is a big no-no in bathroom feng shui, which will make it difficult for the air to stagnate. Only the minimum necessities should be placed, too much clutter should not be placed in the bathroom space, cleaning utensils should not be exposed outside, and there should be special storage. The ideal bathrooms are those with simple furnishings, simple design and good ventilation.

The flow of air and energy will be affected by the material used, and different floor tiles and floor materials will produce different effects. For example, marble, granite, and other hard and smooth surfaces will accelerate the flow of energy, especially when the light is bright and the light is visible. They help create an uplifting, positive atmosphere.

The bathroom is a commonly used place for family members, and the feng shui problem of modern home has formed a craze, and the feng shui condition of the bathroom decoration will directly affect the good luck and luck of the family, so the bathroom will become a topic of conversation in feng shui. Let's briefly talk about the feng shui taboos in the bathroom: 1. The toilet is closed for a long time

If the toilet has no windows or closes the windows for a long time, the filthy gas will not disperse, and it is easy to accumulate yin qi, which will lead to family discord and affect the home. 2.Toilets should not be near the door:

The toilet is too close to the door, it is easy to break the money, and the family quarrels a lot, so the solution is to close the toilet door often. 3.Toilet taboo black:

Bright colors should be used in the toilet, and gloomy tones such as gray, black, and blue should not be used. The toilet itself is already lacking in yang, and coupled with such a gloomy tone, it is equivalent to adding fuel to the fire and provoking yin spirits 4The toilet is built into the kitchen:

If you enter the toilet through the kitchen door first, it is easy to cause gastrointestinal problems and suffer from diseases that will make you sick for a long time.

Answer: The location of the toilet should not be on the north or northeast side of the house, because if it is in both places, it will cause nuisance to people. If the location of the toilet has to be due north and northeast of the house, the angle of the toilet must be slightly offset, with an offset of 15 degrees as the best, and the position of the toilet should be offset by more than 15 degrees. In addition to the north and northeast, toilets cannot be placed in the southwest direction.

If the toilet is in this location, it is better to move it to the northwest location. In addition, the toilet is in the south position, it is best to move it to the east, southeast, northwest position, but the toilet is generally not in the south position, because the south is the location of lighting, but it is not excluded that there are any exceptions, in short, if the toilet is in the south, it is a great hindrance to the owner. In the house where a person born or a girl who is about to get married, the toilet should not be located in the west of the house, otherwise it will be harmful to people.

The toilet should not be located in the center of the house, but must be placed in a position where it is pressed down. The center of the house is the heart of the house, which is very important, and the toilet is a filthy thing, and if the toilet is placed in the very center of the house, it will cause a nuisance to the whole family. At the same time, the toilet should not be located in the northeast or southwest of the house, because there are a lot of filthy things in the toilet, and if placed in these two directions, there will be a situation where the cattle have Tuke water, which is very unlucky and will threaten the health of the family.

The location of the toilet should not be placed on the auspicious position, and even, its location should be preferably the murderous position. In residential feng shui, in order to ensure that the toilet does not bring bad luck to people, the toilet should be placed in the northwest, southeast or east of the house, and avoid the direction of the male and female owners in the direction of their lives.

In addition, the door of the toilet should not be facing the bedroom door and the main door, otherwise it will pollute the living environment. Toilets must have windows that ventilate and expel filth. If possible, you can also place a few pots of green plants in the toilet to absorb the filth.