What should I do if the water in the electric heater becomes less?

I'm sorry, but the friends upstairs didn't get it right. The water is not ordinary water, it is a salt water (in order to conduct electricity). In this regard, when the water of the electric heater is reduced, you can add an appropriate amount of salt water with a higher concentration through the one plus water port on the warmer.

At the same time, it is necessary to pay attention to the work of exhausting the air.

It should be possible to add water into it, but where does the water come from! Some are in an inconspicuous place (under the cover of the electric plug), if you open the plastic cover, you should be able to see a water inlet plugged with a transparent rubber plug, I have made it myself before, I don't know if what you bought is the same as what I bought. Some can directly see a water inlet, pick out the transparent rubber plug with a needle to add water, but be careful not to add too full, seven or eight points full is enough.

Winter temperatures are now very low in many places, resulting in some home insulation products selling well. And compared with the expiration, science and technology continue to develop, people's physique is also declining, there is no way to deal with the cold, and the electric heater has become a choice for many people, but the correct use of warm baby.

It is very important, otherwise there will be a big security risk.

Question, so how to replenish water when the electric heater is short of water, and what to do if there is less water in the warm baby?

If the electric heater needs to replenish water if it is short of water, it is recommended to carefully read the product instruction manual, if there is no introduction to the instruction manual of adding water, you can observe the structure of the electric heater, if there is a water injection port next to the charging plug interface, if there is a water injection port, if there is, it means that water can be added, otherwise the electric heater can not be replenished if there is a lack of water. When the warm baby can add water, you can pick up the plug of the water inlet, but you must store the plug, and the warm baby cannot continue to use it if you lose it.

At present, there are many kinds of warm babies on the market, some can indeed be filled with water, some need to be injected with chemical liquids, and some warm water treasures are electrode type, which is to put two metal electrodes in the hot water bottle, and after the power is turned on, an electric current will be generated, so that the warm baby can heat up.

This kind of warm baby is the hot water bottle that people often use.

In short, it is not that you can add water if there is less water in the warm baby, and disassembling the hand warmer without permission is likely to cause damage to the product. Moreover, the electric heater produced by the regular manufacturer, the amount of water in it is very scientific, unless the quality of the electric heater purchased is not good, the water is suitable, so there is generally no need to add additional water.

The weather is colder in winter, many friends will choose some heating products to keep warm, electric heaters are more popular, there is liquid inside, and the liquid will get hotter and hotter after charging. In the process of using the electric heater, some friends found that the liquid in it became less and did not know what to do. So what should I do if there is less liquid in the electric warmer, and what is the liquid in the charging hand warmer?

If there is less liquid in the electric heater, you can first observe whether the electric heater can be filled with water, specifically according to the manual to operate, look at the structure of the electric heater, if there is a small water injection port next to the charging plug to the manuscript mouth, it means that it can add water, in this case, you can add water directly, if not, you can't add water. From a safety point of view, if the liquid in it is less to a certain extent, it is more dangerous and can not continue to be used, it is best to replace the electric heater with a new one, so that there is no problem with smart change.

The liquid in the charging hand warmer is a conductive liquid, that is, a saturated electrolyte solution, generally a saturated sodium acetate solution, which is a mixture of ethylene glycol and water, and its heating principle is that after the charging hand warmer is energized, the solubility of sodium acetate in it will slowly increase, so that it will absorb heat and begin to dissolve, and after reaching the saturated state, it will begin to release heat crystallization to achieve the effect of heating.

You can add water by yourself, and the steps are as follows:

1. Open the screws of the water inlet of the electric hand warmer.

2. Remove the rubber plug to expose the water inlet.

3. Insert the funnel dedicated to the electric hand warmer.

4. Twist half of the beverage bottle at the top of the funnel.

5. Add water to the mouth with a container (eight lifts can be divided).

6. Re-cover the rubber plug after adding it.

7. Tighten the screws that were removed earlier.

8. Or use it directly after wiping it dry.

You can't add water, the water in it is generally not natural water, it's the kind of yellow water, if you add natural water, what may happen to the weakening effect or something else.

It is possible to add it, but after adding tap water, the heating time will become longer each time. It won't cut off the power by itself if it burns for a long time. Think about it, it's better to buy a new one, after all, it's only a few dozen dollars.

You can add water by yourself, and the steps are as follows:

1. Open the screws of the water inlet of the electric hand warmer.

2. Remove the rubber plug to expose the water inlet.

3. Insert the funnel dedicated to the electric hand warmer.

4. Twist half of the beverage bottle at the top of the funnel.

5. Use a container to add water to your mouth (eight points full).

6. Re-cover the rubber plug after adding it.

7. Tighten the screws that were removed earlier.

8. Use directly after wiping dry.

There is a plastic hole in the warm baby, you can add water from there, it is recommended that you add it as soon as possible, because if there is less water, the heat inside will go bad quickly. Of course, don't add too much.

What should I do if there is less water for electric hand warmers? All you have to do is open the lid on top of it and add tap water.

It's best not to use it, it's a special heating electrolyte, and there is a safety risk if the electrolyte water is less.