How can you unscrew a very tight lid? Is there any clever way to unscrew a very tight lid?

Unscrew the lid of the cup very tightly, and use the rubber bands commonly used by two girls, and the detailed operation method is as follows:

1. First of all, put one of the rubber bands into the cup body and place it in the middle of the cup.

2. Next, put another rubber band on the lid of the cup.

3. The friction is increased due to the rubber band.

This makes it easy to unscrew the lid of the very tight cup.

4. Finally, take a look at the lid of the cup and easily unscrew it.

If the lid is very tight, you can use a cloth on the cap and twist the lid with your hand, and it should be open.

The cover is very tight, and the lid is generally screwed with special tools, if there is no tool, put a dry towel on the hand, so that it may be able to make a lot of strength when twisted.

You can use toilet paper or a towel to wrap the cap and then twist it to open, which increases friction.

Put the bottle in hot water, and according to the principle of thermal expansion and cold contraction, the cap will be loosened, so that it can be easily unscrewed.

Use the tool. Utilizes the lever principle of wrapping towels and chopsticks. It's time to open it. There are also those that sell professional tools.

I always pin a pair of scissors or a screwdriver to the lid and twist it vigorously.

Put the cap in hot water and soak it for a while, and it will come loose. It was easily unscrewed.

How can I unscrew it? It's very simple and dry, and I think if the lid of a bottle is very tight, this can be twisted with pliers, so that it can be said that it can be easily unscrewed.

Unscrew it with pliers or a wrench.

If the lid is too tight, it may be that the air inside is cold and shrinking, so you can try heating it up to see if it can be opened.

1. Assist with paper or towel; 2. Pry the bottle cap; 3. Heating the bottle cap; 4. Pat the bottom of the bottle.

It means that there is air in it, and the gas must be allowed to come out, so that the head of the water cup can be slapped downward.

If there is a ringing mineral water bottle, remove the ring under the lid first; For the others, use a rough towel, one to hold the bottle, and the other to screw the cap, which will be easier to open.

Find a towel to cover it and try to twist it, but if it doesn't work, you can only find a larger plier and clamp it.

Shoot it and the bottom of the bottle will open.

Generally, try to pat the bottom of the bottle.

Unscrew the lid of the cup very tightly, and use the rubber bands commonly used by two girls, and the detailed operation method is as follows:

1. First of all, put one of the rubber bands into the cup body and place it in the middle of the cup body, as shown in the figure below.

2. Next, put another rubber band on the lid of the cup, as shown in the figure below.

3. Because the rubber band increases the friction, you can easily unscrew the lid of the very tight cup, as shown in the figure below.

4. Finally, take a look at the lid of the cup and easily unscrew it, as shown in the figure below.

If you can only unscrew it by hand, and the lid of the can is very tight, it is relatively easy to open it by soaking it in hot water (do not use boiling water to prevent the bottle from bursting) to heat and expand the remaining air inside.

The rubber band is rolled up on the lid and can be unscrewed lightly.

Raise your hands above your head.

Gently smash it to the ground.

Take a straw, bow your head, pout, hold your breath and suck hard.

First wrap the towel around the cap, then rotate it in a counterclockwise direction, or put the bottle in warm water to heat it to keep the pressure inside and outside the bottle balanced, and then slowly twist the cap, you can also pat the bottom of the bottle with your hand, and then twist the cap hard.

1. Unscrew the towel

Very tight caps need to be unscrewed with a towel, less friction when twisting the cap may cause the cap to be difficult to unscrew, use a towel to completely wrap the cap, increase the friction between the hand and the cap, and then rotate it in a counterclockwise direction to unscrew it.

2. Heat the bottle

If the internal pressure of the bottle is lower than the external pressure may increase the difficulty of unscrewing the cap, soak the bottle in hot water for 2 minutes, at this time the air pressure inside and outside the bottle will remain balanced, and then slowly twist the cap.

3. Pat the bottom of the bottle

A very tight cap can be slapped at the bottom of the bottle to unscrew, first turn the bottle upside down, and then slowly pat the bottom of the bottle with your hands, using the impact of water to loosen the cap and the bottle body, but the slapping force should not be too large, so as not to pop out the bottle cap.

There are often a lot of very tricky small problems in life, which are very headaches, so what to do if the lid can't be unscrewed, let's learn together.

In life, you will often encounter lids that cannot be unscrewed, such as cans, or objects that are well sealed.

Method 1: Pat the bottom of the jar with the palm of your hand.

Method 2: Use a spoon to pry the gap between the cans.

Method 3: Place in a bowl with hot water for about 30 seconds and easily unscrew the lid.