Is the door frame and blowing agent firm? What to do?

Decoration is a painstaking thing, there are many important details that need to be grasped in place, otherwise it is easy to bring some trouble to people's daily life after moving in, but there are many decoration methods for the same thing, and most residents do not know how to choose. For example, when installing door frames, many people think that cement mortar is used.

It is more reliable to fix it, but this method is wrong, and instead use a blowing agent.

It should be more firm, but it is necessary to master the correct installation method, measure the size of the door opening in advance and make a right-angle iron frame, and then carry out the blowing agent operation after mastering the correct position. <>

Foaming agent is a kind of adhesive material, as long as it encounters a humid environment, it will show a cured state, not only has a very high adhesive strength, but also can play a role in sound insulation and heat preservation, and can effectively prevent moisture in a humid environment. In fact, the foaming agent will only become aging when exposed to sunlight for a long time, but the problem of light will not appear after the use of attached wooden doors, so the situation that everyone is worried about will not appear, as long as the purchased foaming agent is qualified and the installation method is correct, the door will not have problems under normal use. <>

First of all, the installer needs to splice out the size of the door opening in advance, and then use the right-angle iron frame and the wooden square to adjust the vertical degree of the door. In the process of installing the wooden door, it must be in a horizontal state first, the stressed position must be uniform and firm, and then the foaming agent must be played, the door sleeve line must be installed, and then the door frame is installed after these steps are processed in place, and finally fixed with screws, there is not too much complicated operation, but it must be carried out according to the steps. <>

To sum up, we must do a good job of relevant strategies before decoration, ask for the opinions of professionals, and not be perfunctory by some decoration masters, otherwise it is more troublesome to save when there is a problem with the door frame in the later stage, and the master will not carry out after-sales treatment, which will have a certain impact on daily life, and it will cause danger in serious cases.

The first point is to clean all the sides of the door frame, and the second point is to put the foaming agent on it, so that it is very firm and can be used.

This kind of operation is particularly strong, and certain protective measures should be taken in the process of operation, and it should also be carried out in one direction.

The special frame needs to be beaten with foaming agent firmly, because this can make there be no gap between the door and the brick, shake it before using the foaming machine.

Summary. Dear, hello, I'm glad to answer for you, dear, the door frame styrofoam is played like this: the door frame is injected between the door frame and the wall before filling the styrofoam, first clean the wall, moisten the wall with a watering can, fill the styrofoam, pay attention to the styrofoam filling should be appropriate, and the excess styrofoam should be cut flat with a blade.

Install the door sleeve line After the styrofoam cures for 4-6 hours, remove the tooling and wooden wedge, apply glue in the door frame socket, and then embed the door sleeve line into the door frame, and gently knock and compact to make the door sleeve line fit closely with the wall.

How to hit the styrofoam of the door frame.

Dear, hello, I'm glad to answer for you, dear, the door frame styrofoam is played like this: the door frame is injected between the door frame and the wall before filling the styrofoam, first clean the wall, moisten the wall with a watering can, fill the styrofoam, pay attention to the styrofoam filling should be appropriate, and the excess styrofoam should be cut flat with a blade. Install the door sleeve line After the styrofoam cures for 4-6 hours, remove the tooling and wooden wedge, apply glue in the door frame socket, and then embed the door sleeve line into the door frame, and gently knock and compact to make the door sleeve line fit closely with the wall.

Pro, when using styrofoam, try to keep the speed even. Generally, it is enough to spray the amount to 2 3 of the required filling volume, do not spray full. When filling vertical gaps, it is recommended to fill them from the bottom up, so that gravity can be used to prevent falling.

Then wait for about ten minutes for the foam to bond; After 60 minutes, the cut is ready to take place.

Summary. What can be used to clean the foaming agent on the door frame? 1. You can use the polishing water to remove the nail polish pigment to wipe it off, but because the polishing water is likely to cause the original color of the door to fall off, it is recommended to try it in a small place that is not obvious first.

2. You can take a dry cloth stained with vinegar to cover the entire foam glue traces, and wait until the sticky stains of the double-sided tape are completely soaked, and you can easily remove them with a ruler. 3. You can use heating to soften the adhesive of double-sided tape: blow it with a hair dryer to soften the adhesive, and when the adhesive of the foam glue becomes weaker, it can be easily removed.

If there are still small marks, wipe them off with polish remover that removes nail polish. 4. Finally, when cleaning, whether you use polishing water or vinegar, you must let these supplies completely soak the foam marks to easily and effectively remove them.

What can be used to clean the foaming agent on the door frame? 1. You can use the polishing water to remove the nail polish pigment to wipe it off, but because the polishing water is likely to cause the original color of the door to fall off, it is recommended to try it in a small place that is not obvious first. 2. You can take a dry cloth stained with vinegar to cover the entire foam glue traces, and wait until the sticky stains of the double-sided tape are completely soaked, and you can easily remove them with a ruler.

3. You can use heating to soften the adhesive of double-sided tape: blow it with a hair dryer to soften the adhesive, and when the adhesive of the foam glue becomes weaker, it can be easily removed. If there are still small marks, wipe them off with polish remover that removes nail polish.

4. Finally, when cleaning, whether you use polishing water or vinegar, you must let these supplies completely soak the foam marks to easily and effectively remove them.

Okay thank you.

Kiss! Hello, happy to answer your <>

2。Press the door frame against the wall and take it down to break the foam. 3。

Expose the foam to the air for 1-2min, blow the bubble with caution, the foam does not move, and the surface is initially dry. 4。Reinstall the door to the wall and adjust the position, and place the positioning rod to prevent the styrofoam from swelling.

Door sleeve gluing skills: 1. When we glue the doors and windows, we must keep its direction horizontal, the horizontal level of each layer of the vertical pull-through line is consistent, and the top and bottom must be straight, and the gluing of the door and window in this direction can prevent the fracture of the glue. 2. Then fix the upper frame first, and then fix the frame, there must be such a sequence, when gluing, you must step on the expansion screw to fix the window frame and the window frame opening, and the expansion and contraction place must be fixed with foam, so that the sealing of the door and window can be guaranteed after the glue.

3. When gluing doors and windows, the effect of filling the door frame with foaming agent is better, I hope mine can help you <>

If you have any other questions, you can ask me again<>

It should be reliable, because our home decoration doors are all selected party foaming agent, and there is no damage or anything.

When decorating the door frame, you should choose a foaming agent, like my home when decorating the door frame, the effect is still very good, the decoration is very strong, and the door frame looks very atmospheric.

When installing the door frame, you should choose a blowing agent, so that the whole door frame will be installed particularly firmly, and the whole door frame will look very beautiful and beautiful.