Is it okay to brush the adhesive on the cement base and directly paste the interior wall tiles? What

Updated on home 2024-07-13
11 answers
  1. Anonymous users2024-02-12

    The adhesive is a kind of super glue brushed on the reverse side of the porcelain tile, and its key function is to improve the compressive strength of the bond between the tile and the pasting raw material layerto prevent the quality problems of the wall after the tile is paved and falls off. Tile adhesive is made of high-quality polymer polymer moisturizing emulsion raw materials and organic silicate materials, and the current common ceramic tile adhesives include moisturizing emulsion tile adhesive, component tile adhesive, and clay tile adhesive.

    It can be said that for porcelain tiles, whether it is general interior wall tiles or floor tiles on the wall, adhesive is the key auxiliary material to ensure the quality of paving, and it is also one of the indispensable materials. For the adhesive, although it has such a great effect, it must be used in the right part, if the wrong part is used, it will make the adhesive give full play to all the effects. According to the provisions of the adhesive application processing technology, it is necessary to apply the adhesive brush on the reverse side of the neat and dust-free tile, and then place it in a dust-free place to carry out the drying of course, until the application, cooperate with each other to balance the cement to carry out the paving, which can ensure the solidity of the wall on the interior wall tiles or floor tiles, and it is not easy to bulge and peel off.

    Home decoration, living balcony, dining room, kitchen, and toilet are mainly pasted with wall tiles and floor tiles. Because the main purpose of the house is different, the application of a way to paste different bedroom tiles, the actual effect of pasting is not very ideal, especially in the application of tile adhesive, adhesive on the wall flatness is very high, the wall is uneven, the application of adhesive paste tile is not firm, it can be said that there is no way to paste. Brush the adhesive on the top of the concrete base layer, and immediately paste the tiles have never been understood.

    The tile is glued into a barrel of emulsion liquid, which can only be brushed on the reverse side of the tile, and cannot be brushed on the bottom layer of concrete. The application of adhesive paste interior wall tile tiles, the tile must be solved by small blisters, so that the tile is fully digested and absorbs water, at the same time, the reverse side of the tile film release agent is cleaned and tidy, the wall is neat and clean, and the wall is fixed with "wall solid" glue, 108 glue, waterproof putty to upgrade the goods, good wettability, improved adhesion, usually the wall must be brushed twice to fix the adhesive, through the small blister to solve the tile, and there is no water after drying, the next procedure can be realized.

  2. Anonymous users2024-02-11

    Actually, I don't think that's okay; Because this method of sticking can easily lead to the later stage may cause the tile to fall off or there is a hollow drum phenomenon, the tile pasted by this method is not reliable, the significance of the adhesive is mainly to make the tile and the paste material stick more firmly, not to make the tile paste material and the wall paste more firmly.

  3. Anonymous users2024-02-10

    I think no, this will make the tile unreliable, and after drying, it is likely to produce cracks, I think it is necessary to pay attention to the cement to get a more suitable hardness, and to wash the tiles with water in advance, so as to strengthen the cement for the wall and tile adhesion.

  4. Anonymous users2024-02-09

    Of course not, first of all, it is not possible to brush the adhesive on the cement base layer and stick it directly on the interior wall. Because whether it is a floor or an interior wall, adhesive is a necessary pasting material, if not used, it will fall off later, so when pasting adhesive. Pay attention to natural drying, and paste it on the table when laying.

  5. Anonymous users2024-02-08

    Kiss! Hello, happy to answer your <>

    You can't brush the adhesive on the whole tile, you can't use cement mortar to stick the wall tiles, you must use a special adhesive to paste the wall tiles. It is very easy to use cement mortar to stick wall tiles with hollow drum tile adhesive and cement can be combined, and the effect is not as good as directly brushing to the back of the tile, so it is not recommended to brush cement, especially in the bathroom because it is not waterproof, but also prone to water seepage problems, tile adhesive and cement can not be combined, if the tile adhesive and cement are mixed together, it will cause damage to the ratio of tile adhesive, resulting in it containing too much cement, so that the tile adhesive rigidity is too large, after paving the tile, it is easy to have the problem of tile cracking. After the tile is brushed, you can not directly use cement mortar to paste the tile, it is recommended to use tile adhesive.

    Tile adhesive is recommended to use Keshun waterproof C600 glass virtual brick special tile adhesive. Tile adhesive is a new type of material for modern decoration, replacing the traditional cement yellow sand, the adhesive adhesion is several times that of cement mortar, which can effectively paste large ceramic tiles and stones, and avoid the risk of falling bricks. Good flexibility to prevent hollowing in the production of drums.

    It is mainly used for pasting decorative materials such as tiles, face tiles, floor tiles, etc., and is widely used in interior and exterior walls, floors, bathrooms, kitchens and other building finishing decoration places. Its main characteristics are high bonding strength, water resistance, freeze-thaw resistance, good aging resistance and convenient construction, which is a very ideal bonding material. I hope my wheel can help you <>

    Do you have any other questions?

  6. Anonymous users2024-02-07

    Summary. Cement wall tiles can be used, but there is no need to brush the adhesive. Cement wall tiles are also tile glue.

    1. Do you need to brush the adhesive with tile adhesive? 1. If the flatness of the base layer is poor, when the thermal expansion and contraction are cold, the bonding interface between the tile and the tile adhesive will have a large additional stress between the layers, resulting in the hidden danger of the tile falling off, and with the tile adhesive, the tile paving can be more stable, reduce the probability of the tile falling, and greatly improve the safety of tile paving. Especially in the construction of the base surface of the elevator hall and the hollow wall, the use of adhesive can effectively improve the firmness of the tile paving.

    2, but with tile adhesive but also brush adhesive, in addition to a lot of materials, undoubtedly increase the complex process, and tile adhesive is more difficult to dry, after the coating to wait for its drying before the tile adhesive construction, from the cost and time point of view, the use of ceramic tile adhesive is not cost-effective, if the base surface is flat, can not be brushed, according to the actual budget.

    Cement wall tiles can be used, but there is no need to brush the adhesive. Cement wall tiles are also tile glue. 1. Do you need to brush the adhesive with tile adhesive?

    1. If the flatness of the sail layer of the foundation hole is poor, when the thermal expansion and contraction are cold, the adhesive interface between the tile and the tile adhesive will have a large additional stress between the hail layers, resulting in the hidden danger of the tile falling off, and with the tile adhesive, the tile paving can be more stable, reduce the probability of the tile falling, and greatly improve the safety of tile paving. Especially in the construction of the base surface of the elevator hall and the hollow wall, the use of adhesive can effectively improve the firmness of the tile paving. 2, but with tile adhesive but also brush adhesive, in addition to a lot of materials, undoubtedly increase the complex process, and tile adhesive is more difficult to dry, after the coating to wait for its drying before the tile adhesive construction, from the cost and time point of view, the use of ceramic tile adhesive is not cost-effective, if the base surface is flat, can not be brushed, according to the actual budget.

    Second, the use of tile adhesive precautions 1, the base to keep the base and tile adhesive contact with the wall or ground, to clean off the floating dust, oil stains and other substances, vertical elimination, otherwise the adhesive effect of tile adhesive will be affected. 2. If the thickness of the tile adhesive and the construction are uneven, there will be a situation where the corners of the paving can be warped and hollow. 3. Tile adhesive can not be soaked in water, and tiles are paved with tile adhesive without soaking in water, because the tile adhesive has a strong water retention capacity.

    If the tile is directly applied with tile adhesive, the adhesive strength will be reduced, causing the tile to fall off. 4. The tile adhesive should be used up within two hours, and the tile adhesive after drying can not be used for tiling. 5. Tile adhesive does not need to be used with water, because tile adhesive is a polymer with a variety of materials, and there is no need to add water to use, otherwise it will affect the construction effect.

  7. Anonymous users2024-02-06

    Summary. Yes, under normal circumstances, it is necessary to paste the adhesive after pasting the adhesive in the paste, and the finishing effect will be better, if you do not brush the adhesive, the paste effect may not be good in the later stage, and it is easy to fall off. Rock slabs are mainly used in the field of home and kitchen slabs.

    As a new species in the field of home furnishing, compared with other home furnishing products, rock slab home furnishing has the characteristics of large specifications, strong moldability, diverse colors, high temperature resistance, wear and scraping resistance, anti-penetration, acid and alkali resistance, zero formaldehyde, environmental protection and health.

    Yes, under normal circumstances, it is necessary to paste the adhesive after pasting the adhesive and the field is in the paste, the finishing effect will be better, if you do not brush the adhesive, the later paste effect may not be good, and it is easy to fall off. Rock slabs are mainly used in the field of home furnishings and kitchens. As a new species in the field of home furnishing, compared with other home furnishing products, rock slab home furnishing has the characteristics of large specifications, strong moldability, diverse colors, high temperature resistance, wear and scratch resistance, anti-penetration, acid and alkali resistance, zero formaldehyde, environmental protection and health.

    Ask about custom messages].

  8. Anonymous users2024-02-05

    The whole brick wall is brushed with adhesive, and then pasted with cement mortar. May I?

    Kiss! Hello, happy to answer your <>

    Pro, the whole brick wall brush adhesive, with cement sand plaster paving is not 100% insurance. It is recommended to use the following three methods to ensure that the bricks will not fall. First:

    Brush the adhesive first, air dry and then scrape a thin layer of tile adhesive, and then pave with cement mortar. The second type: make a shallow groove on the back of the tile, bury a copper wire or stainless steel L-shaped hook, and fix it with AB glue.

    Remove the dust, brush the adhesive, air dry, pave with cement sand plaster, and then fix the copper wire or L-shaped hook on the wall with nails. Third: thin paste.

    First, the wall is leveled vertically to ensure that the error does not exceed 2mm, and the tile glue is scraped vertically on the wall with a sawtooth gray board, and the back of the tile is scraped horizontally, and the cross is carried out for construction. The whole body brick is made of rock chips after high-pressure pressing and then firing, and the hardness of the surface polishing can be compared with the stone, the water absorption rate is lower, and the wear resistance is good. The surface of the whole brick is not glazed, and the material and color of the front and back of the wheel are the same, hence the name.

    I hope my eyes can help you <>

    Do you have any other questions?

  9. Anonymous users2024-02-04

    Summary. No. Tile must be made of cement and sand in proportion to the sand ash, pure cement does not have the strength of sand and ash is easy to cause hollowing.

    Solve the problem of tile hollowing falling off. The construction method is as follows: the adhesive is divided into two components and one component, and the quality of the two components is stable, so it is recommended to choose.

    During the construction, the back adhesive is stirred in proportion on the site, and then evenly painted on the back of the tile, and it dries after 24 hours, and the cement mortar can be directly used for bonding construction. At present, tooling is used more.

    Can the whole tile be brushed with adhesive with cement mortar? wall tiles.

    No. Tile must be made of cement and sand in proportion to the sand ash, pure cement does not have the strength of sand and ash is easy to cause hollowing. Solve the problem of tile hollowing falling off.

    The construction method is as follows: the adhesive is divided into two components and one component, and the quality of the two components is stable, so it is recommended to choose. When the construction is fierce, the back adhesive is stirred in proportion on the site, and then evenly painted on the back of the tile, and it is dry after 24 small bends, and cement mortar can be directly used for bonding construction.

    At present, there are more spring boring tooling uses.

    But when I pasted it like this, a large area fell off.

    No, it won't. The whole tile is coated with adhesive, and the wall is also coated with adhesive, and the cement is glued with glue, which can be peeled off in a large area.

    No, it won't.

  10. Anonymous users2024-02-03

    Summary. After pasting tiles with tile adhesive, there is generally no need to brush the adhesive. Of course, if you want to make the tile paving more firm, you can also use adhesive, which can reduce the probability of falling tiles, improve the firmness of tiles, and extend the service life of tiles.

    In the construction of the base surface of the elevator hall and the hollow wall, the use of adhesive can also reduce the additional stress and improve the firmness of the tile paving.

    After pasting tiles with tile adhesive, there is generally no need to brush the adhesive. Of course, if you want to make the tile paving more firm, you can also use adhesive, which can reduce the probability of the tile falling beam, improve the firmness of the tile, and extend the service life of the tile. In the construction of the base surface of the elevator hall and hollow wall, the use of adhesive can also reduce the stress of additional slag and improve the firmness of tile paving.

    The wall tile adhesive can be brushed with adhesive or not. 1. If the flatness of the base layer is poor, when the thermal expansion and contraction are cold, the bonding interface between the tile and the tile adhesive will have a large interlayer additional stress, resulting in the hidden danger of the tile falling off, and with the tile adhesive, the tile paving can be more stable, reduce the probability of the tile falling, and greatly improve the integrity of the tile paving. Especially in the construction of the base surface of the elevator hall and the hollow spring slag core wall, the use of adhesive can effectively improve the firmness of tile paving.

    2, but with tile adhesive but also brush adhesive, in addition to a lot of materials, undoubtedly increase the complex process, and tile adhesive is more difficult to dry, after the coating to wait for its drying before the tile adhesive construction, from the cost and time point of view, the use of ceramic tile adhesive is not cost-effective, if the base surface is flat, can not be brushed, according to the actual budget.

  11. Anonymous users2024-02-02

    The second method is to use some cement mortar, using tools to apply cement mortar to the wall, creating some rough bumps on its surface. The third method is to use a high-pressure water gun, which is used to rinse the wall, leaving some small dimples on the wall. It should be noted here that when using adhesive, it is necessary to pay attention to the thickness of the adhesive backing, too thin and too thick will affect the effect of tiling.

Related questions
7 answers2024-07-13

Check the loose thickness when paving, cement dose, compaction times, compaction degree, loose paving thickness with a ruler, on-site measurement, according to the test section to determine the loose thickness, cement dosage with EDTA titration (specification JTGE51-2009 has a method), the other 2 needless to say, it's too simple.

11 answers2024-07-13

1. You can use putty first.

If there is still a part of the shovel that cannot be removed using hydrochloric acid or phosphoric acid solution, wipe it several times. 2. Due to some types of ceramic tiles (such as antique tiles, polished tiles. >>>More

10 answers2024-07-13

1. First prepare a piece of soap for later use.

2. Next, wet the cement stain on the pants with water. >>>More

15 answers2024-07-13

Research shows that more than 70% of corporate strategies are not implemented or are not effectively executed. If there is no problem with the strategy itself, the main reason is the lack of execution. If this question goes further, what is the reason for the lack of execution? >>>More

23 answers2024-07-13

In the polishedCement slabsA layer of concrete mortar is laid on it, how to do it so that it is not easy to loosen, and the length of the pipe is longer. In fact, there are many situations like thisAnyone who has ever done engineering construction will encounter it. In fact, there are many such conditions in rural areas, like the original cement prefabricated panels. >>>More