What is the problem that the water level slowly drops after the toilet tank is full, and there are n

Observe whether the water falling in the tank is leaking into the toilet and whether it is falling to a small amount of water.

Drain location. If it is slowly leaking into the toilet, it is lowered to the small drain position, which is a tank drain valve system with large and small flush water and two buttons. Check the small water drain valve (half hole and half drain), small water level adjustment, whether the adjustment is in place, whether it is out of balance (out of control) or whether the small water drain button can be pressed and bounced up normally, etc., resulting in the small water drain valve can not be fully controlled and closed.

Yes, after the toilet tank is full, the water level drops, it is to prevent, the water level outflow of the leather pad, there are sundries on it, the solution is very simple, open the back cover of the toilet, against the cylinder of the dark water level, twist it left and right, take it out after the activity, take it out and clean up the stains below, at the bottom of the toilet back box, you will see a black leather cushion, take it out and clean it, rinse it with clean water and then install it. Attach the cylinder that presses the water out, and after tightening it, it will not overflow. It's so easy you can give it a try.

If there is a leakage, it will fall quickly and slowly, so there is no water mark, which proves that the stay time is very short, and the decline is not slow, but quite fast, so plugging the leakage is the most important thing.

See if there is any leakage under the tank. Sometimes there are no water marks when the toilet leaks, and you have to look carefully to see the movement of the water to find out.

What is the problem that the water level slowly drops after the toilet tank is full, and there are no water marks in the toilet? I might think that in this case, it may be because the parts inside are broken, which is why this is the case.

First of all, you have to find out where the water is leaking, if the water in your tank is dropping, and the toilet is flowing slowly, it should be that there is a problem with the overflow valve of the control valve, if it is a leak at the back of the toilet, that is, the underground water storage of your toilet should be, there is a problem with the sealing ring. If you can't find out where the water is leaking? It is very likely that the toilet itself is cracked and the water is leaking into the sewer.

Summary. Hello, I am happy to answer your questions, the toilet water seal slowly decreases may be caused by these situations: the plastic pipe falls off, the installation of the toilet is uneven, there are cracks in the position of the water cover, there are cracks and sand holes at the bottom, etc.

First, the plastic pipe falls off should first check the toilet tank, there is a plastic pipe about half a centimeter thick connected to the overflow pipe in the toilet tank, to see if it slips off, if it slips off is not on the overflow pipe, connect it on it. Second, the uneven installation of the toilet may be caused by the uneven installation of the toilet at the time of installation. However, it is quite unlikely, because if the installation is uneven, the inclination is quite obvious, and it is easy to find, plus the area of the water cover in the toilet bowl is fixed and cannot be changed, it is even less likely.

Third, there is a crack in the position of the water cover, check to see if there is a crack in the position of the water cover of the toilet. The easiest way to do this is to stroke the water cover with your hand and feel for cracks. Fourth, if there are cracks and sand holes at the bottom, it will also lead to the water level of the water seal not meeting the functional requirements.

If this is the case, you can take the toilet down and check it, and if it is broken, replace it.

After the toilet tank was full, the liquid level began to drop slowly, and I don't know where it leaked.

Hello, I am happy to answer your questions, the toilet water seal slowly decreases may be caused by these situations: the plastic pipe falls off, the installation of the toilet is uneven, there are cracks in the position of the water cover, there are cracks and sand holes at the bottom, etc. First, the plastic pipe falls off should first check the toilet tank, there is a plastic pipe about half a centimeter thick connected to the overflow pipe in the toilet tank, to see if it slips off, if it slips off is not on the overflow pipe, connect it on it.

Second, the uneven installation of the toilet may be caused by the uneven installation of the toilet at the time of installation. However, it is quite unlikely, because if the installation is uneven, the inclination is quite obvious, and it is easy to find, plus the area of the water cover in the toilet bowl is fixed and cannot be changed, it is even less likely. Third, there is a crack in the position of the water cover, check to see if there is a crack in the position of the water cover of the toilet.

The easiest way to do this is to stroke the water cover with your hand and feel for cracks. Fourth, if there are cracks and sand holes at the bottom, it will also lead to the water level of the water seal not meeting the functional requirements. If this is the case, you can take the toilet down and check it, and if it is broken, replace it.

If the above methods cannot solve this problem, it is recommended to ask the relevant maintenance master to repair it.

When the toilet tank is full and the water level slowly drops, there are no water marks in the toilet, which may be caused by the following reasons:

Clogged drains: The drain of the toilet can be clogged due to slippery drains, preventing water from flowing out of the toilet.

Leaking water inside the water tank: The water tank of the Paling toilet may have a leaking problem, causing water to keep flowing out of the tank.

Leaking at the bottom: There may be a leak at the bottom of the toilet, causing water to constantly seep out of the bottom.

If this is the case for you, it is advisable to seek the help of a professional to ensure that your toilet is working properly.

There may be a leak in the water tank.

Summary. Answer: Hello Kiss Question: The water in the toilet pit is slowly decreasing, it is estimated that the height of the water seal is fixed, and the only thing that can be changed is the water supply pipe on the water parts in the toilet tank to adjust.

Generally, there is a small hose on the double-gear water piece, called the water replenishment hose, the water replenishment hose is placed directly in the water tank, the water seal height is low, if it is placed in the water replenishment hole, the water cover is relatively high. This is the easiest and most effective way to adjust. Different types of toilets, different manufacturers' designs, water seal heights are also different.

Answer: Hello kiss Question: The water in the toilet pit is slowly decreasing, it is estimated that the height of the water seal is the height of the water seal, and the height of the water seal is determined in the solid, and the only thing that Tan Sui can change is the water supply pipe on the water part in the toilet tank to adjust. Generally, there is a small hose on the double-gear water piece, called the water replenishment hose, the water replenishment hose is placed directly in the water tank, the water seal height is low, if the peizi is placed in the water replenishment hole, the water cover is relatively high.

This is the easiest and most effective way to adjust. Different types of toilets, different manufacturers' designs, water seal heights are also different. 殺殺

1. There is too little water in the toilet pit, which is related to the structure of the toilet, different product structures are different, and the amount of water will be different, if the water in the toilet bowl in normal use suddenly becomes less, it may be because the water pressure is too large, the water in the water tank is too full, and the pressure becomes larger, and the siphon phenomenon will be more intense when the flush button is pressed, and the water remaining in it will naturally become less after flushing. 2. You can try to adjust the water press lever in the water tank, most of the toilets on the market are water-saving toilets, after using it for a period of time, you will find that the water press inside becomes too high, at this time the water in the toilet will become too stressful, and the toilet leaves too little water after flushing, you can try to adjust the adjustment pressure rod in the water tank down, so that the water volume will sail down, and do not adjust the finch skin at a time, and you will find the right position if you try a few more times. Then tighten the screws and you're good to go. 3. Adjust the water inlet valve, the water inlet valve becomes higher after a period of use, resulting in too much pressure and too fast water outlet, at this time, it is necessary to disassemble the water inlet valve, remove the water inlet valve buckle inside, and adjust the height according to the counterclockwise rotation, so that you can adjust the problem of too little water in the toilet

How to solve the problem of less water out of the toilet 1, this situation may be related to the size of the faucet, if the faucet is less water, the water will be very slow, this is because there is a filter screen in the position of the water replenisher, and the filter will be blocked after a long time with a key, which will affect the water flow, as long as the filter is cleaned regularly. 2. You can also replace the water distributor, and the position of the water filler is under the toilet, which is connected with a plastic pipe, and can be removed with a wrench to replace the new one, and the water filler is very convenient to replace. 3. Dirt accumulation, the toilet tank is stupid and simple to accumulate water for a long time, and after a long time, it will accumulate a lot of dirt, which will affect the water output, you can put the toilet cleaner inside the toilet, or laundry detergent, so that when the water inside the water tank flows, the dirt will be discharged out of the outside, and the dirt on the inner wall and pipe will be much cleaner

Hello, dear, the toilet is open and hidden into the water but the water level does not rise Reason: Xi Hall 1 may be that the toilet tank is blocked by foreign objects, first empty the water in the toilet tank, do not stay, and then use a rag to clean up the foreign objects in the toilet tank, and then try to flush. 2. It may be that the toilet flush button has been used for a long time, and it has not bounced back normally, and it is easy to jam.

3. Check that the water level of the water tank is abnormal, if it is too loose or too high, the water level will exceed the overflow water level and flow back into the toilet, and then readjust the limit installation.

The reason why the toilet does not stop flowing after use is that the plastic gasket on the outlet hole of the pumping system is aging and elastic enough to be sealed. Workaround:

1. Whether the black semi-circular float on the overboard assembly is properly covered, or the black semi-circular float falls off, or the rope is stuck or the black semi-circular float is deformed;

2. The single toilet downspout component is shaken by hand, if it shakes, it means that the semicircular fixing piece at the bottom of the downspout component is broken or loose. The water in the water tank, if the pipe full of the downwater assembly flows out, it is necessary to check the water inlet assembly: there is an adjusting screw on the water inlet assembly, which is used to adjust the water level.

Try to tighten it first, if not, it may be that the water-stopping core (or water-stop film) in the water inlet assembly needs to be replaced.

3. The water stop is generally sold in the wholesale market of household appliances in the city, and the whole set of flushing equipment is generally sold in the plumbing equipment store of the hardware store, which is simple to replace, and can generally be replaced by itself or the merchant can replace it on behalf of the merchant.

There is a float inside the toilet, press it will open the outlet valve to flush the water, and then the water level drops, the lid will automatically cover the water outlet, after the water is injected, the float rises, to a certain water level, automatically close the inlet valve, there is water flowing out of the toilet, that is, the lid is not covered, the float is stuck, and it cannot float normally.

My new one is the same as you said, I don't know what's going on, has your toilet problem been solved?

There's a float in there, and it's estimated that the float hasn't gotten stuck, so just dial it with your hand.

The water in the toilet tank is not satisfied because of the problem of adjusting the water level of the inlet valve, and the following is a way to increase the water level of the inlet valve, and the specific operation method is as follows:

1. First remove the lid of the toilet tank as shown in the figure below.

4. Then lift the water level adjustment switch of the inlet valve of the toilet tank upwards.

5. Finally, cover the lid of the toilet tank, so that you can solve the situation that the toilet tank is not satisfied with the water.

Judging from the problem described, it is caused by the toilet inlet valve opening too small and the water pressure is not enough. No matter what brand of toilet it is, if the water inlet pressure is not enough and the water is served slowly, it will cause such a problem. The floating bucket cannot be quickly put on the water, and the water cannot be sealed immediately when it reaches a certain height, and this phenomenon will occur.

Open the inlet valve wide and let the tank fill up quickly, and this problem is solved. And that's the real savings.

If the inlet water is turned up, there is still this situation that the water cannot be sealed, that is, there is a problem with the tank accessories.

Summary. After the toilet tank is full, the water level slowly drops, and there are no water marks in the toilet, what is the problem may be that the amount of water in the water tank is small, and the length of the pressure rod changes, causing the water stop pad to reset and stop the water quickly. First of all, it may be that the amount of water in the water tank is small, and the length of the pressure rod changes, resulting in the water stop pad quickly resetting the water stop, and the length of the pressure bar can be adjusted to the appropriate one.

Or the water level of the inlet valve is low, remove the inlet valve buckle, turn the inlet valve body counterclockwise, and then adjust the height of the body accordingly, and finally rotate the water inlet valve body clockwise to install the buckle, and connect the filter and the water inlet pipeline.

What is the problem that the water level slowly drops after the toilet tank is full, and there are no water marks in the toilet?

After the toilet tank is full, the water level slowly drops, and there are no water marks in the toilet, what is the problem may be that the amount of water in the water tank is small, and the length of the pressure rod changes, resulting in the water stop pad quickly reset and stop the water. First of all, it may be that the amount of water in the water tank is small, and the length of the pressure rod changes, resulting in the water stop pad quickly resetting the water stop, and the length of the pressure bar can be adjusted to the appropriate one. Or the water level of the inlet valve is low, remove the buckle of the rotten water inlet valve, rotate the inlet valve body counterclockwise, and then adjust the height of the body accordingly, and finally rotate the inlet valve body clockwise to install the buckle, and connect the filter and the water inlet pipe.

I saw that the water level of the water tank was quite high at the beginning, and it slowly dropped for a while, and there were no water marks in the toilet, where did the leaking water go, it may be that the amount of water in the water tank was small, and the length of the pressure rod changed, resulting in the water stop pad quickly reset and stopped the water. First of all, it may be that the amount of water in the water tank is small, and the length of the pressure rod changes in the middle of the training, which causes the water stop pad to be reset quickly to stop the water, and the positive source of the length of the neutral pressure bar can be adjusted to the appropriate level. Or the water level of the inlet valve is low, remove the inlet valve buckle, turn the inlet valve body counterclockwise, and then adjust the height of the body accordingly, and finally rotate the water inlet valve body clockwise to install the buckle, and connect the filter and the water inlet pipeline.

As you said, I know that the water has started to flow very well, and the water level is also high, but the water level is slowly falling automatically. The falling water does not know where it goes.

Are you there. Back to the tank.

Circulatory action. Save water.

Where does the falling water exist and then return to the tank? There is also a drop to a certain extent on the water valve makes a sizzling sound on the water.