There was an urgent need for a plan to make a globe

Materials: table tennis balls, wire, adhesive tape, plasticine, etc.

1. Draw a circle with a red pen in the middle of the table tennis ball as the equator; Drill a small hole on each side of the equator so that the distance from the hole to each point of the equator is equal.

2. Bend the wire into a semi-circular shape, pay attention to the angle of the inclined wire and the perpendicular line, and the angle bent is slightly larger than that of a table tennis ball.

3.Thread the ping pong ball with a slanted wire.

4.At both ends of the inclined wire, wrap it with adhesive tape a few times, so that the table tennis ball can be fixed in the middle of the inclined wire, and at the same time can rotate freely.

5.In the lower part of the wire, wrap some plasticine, so that a small globe will not be reversed.

You didn't say the size of the role of the offer of several: use a round bar car one; Waste Blue Ball; Thin plastic sheets are glued.

The whole production process is a four-step process:

Draw a map of the world on the surface of a full ping pong ball.

At both ends and a quarter of the thin iron sheet, drill a small hole and bend it into an arc as a globe support.

Cut a piece of the ball with a diameter of 20 mm on half a ping-pong ball and glue it to a piece of log. Grind a 4 mm diameter strip of wood with sandpaper at one end into a smooth log strip with a diameter of 3 mm, and glue it to the center of the sphere as a bottom pad.

Attach the bracket to the base with a pin. Thin steel wires are passed through the center of the North and South Poles and fixed at both ends of the bracket so that the globe can rotate freely around the axis.

Remember to be careful when you do it!! Hehe!!

Here's how to make a globe:Tools Raw materials: rubber balls, bracelets, wires.

1. Prepare a rubber ball, bracelet and wire.

<>2. Use a tool to pierce a hole in the rubber ball.

3. Thread the wire into the goal.

4. Use pliers to cut off the excess part.

5. Cut the bracelet in half.

6. Use hot glue to fix half of the bracelet and the globe.

7. Remove the lid of the empty paint jar.

<>8. Glue the globe to the lid.

9. Finally, use a marker pen to color the globe.

The materials and steps of the homemade globe are as follows:1. Start by taking a table tennis ball.

Draw the necessary meridians and parallels, such as the north and south latitudes of the equator, the poles, and the prime meridian.

and 180 warps and so on. Of course, if you are very good at drawing, you can also draw a map of China.

But drawing a map on table tennis is not so easy.

2. After drawing the ball of the globe, we still have to make a hole in the poles of the poles, there is no hole on the earth, but our globe is fixed on the bracket, and we still need to use it. In this way, the ball of the globe is considered to be ready. Now let's make a globe bracket.

The easiest way to do this is to use iron wire and fold it into the shape of a globe holder.

3. Then put the ball into it and adjust the appearance of the bracket, so that a simple globe is done.

4. Color and calibrate the area of the globe that can be used on seven continents.

The five oceans are marked out and decorated with colored pens to make them more beautiful.

You can't do this yourself, the requirements are relatively high, just buy one, it's not expensive, and it's simple and convenient.

<>Step 1: First, take a ping pong ball and draw the necessary longitude and latitude, such as the north and south latitudes of the equator, the pole, the prime meridian and the 180 meridian, etc. Of course, if you are very good at drawing, you can also draw a map of China, but it is not so easy to draw a map on table tennis.

Step 2: After drawing the globe ball, we still need to make a hole in the poles, there is no hole on the earth, but our globe is fixed on the bracket, and we still need to use it. In this way, the ball of the globe is considered to be ready.

Now let's make a globe bracket. The easiest way to do this is to use iron wire and fold it into the shape of a globe holder.

Step 3: Then thread the ball in and adjust the appearance of the bracket so that a simple globe is ready.

Step 4: Color and calibrate the area of the finished globe, mark the seven continents and five oceans, and decorate it with colored pens to make it more beautiful.