-
First of all, look at the mixed mortar, which is dominated by concrete, add river sand and some moisture-proof additives, and then mix with water, which is basically zero environmental pollutionThe adhesion is improved, and the price is also discounted. But what is not so good is that the mixed mortar suffers from many external causes and is very easy to fall off. Secondly, the strength of the floor tiles on the market is getting higher and higher, and the key is that the water absorption capacity is not very good, so the floor tiles often fall off.
From the outside, tile adhesive is similar to concrete, mainly with water, and then immediately used for wall tiles.
However, tile adhesive has an advantage that concrete does not have, that is, it is less susceptible to external damage and is resistant to low temperatures and moisture. A not-so-good point is likely to be expensive, and many unpopular tile adhesives on the market are mixed, and there may even be formaldehyde pollution. Compared with concrete and tile adhesives, the adhesive characteristics of ceramic tile adhesives will be better, and the key is that you don't need to run the floor tiles in advance, and you can paste them immediately.
There is no need to paint a thick layer on the wall, and it is basically very strong after pasting.
There is no doubt that the wall tiles on the floor tiles cannot be pasted with traditional construction techniques and materials, and new technologies and new processes should be used for practical operation. In the work of tiling, the tile adhesive with stronger viscosity should be used to paste the tile, and it is not recommended to apply concrete or mixed mortar to paste, and it is not recommended to choose the way of mixing the application of tile adhesive and cement in order to better save costs. Because the wall tiles on the floor tiles are not the same as the wall tiles on the bottom layer of the wall, the bottom layer of the wall has a certain water absorption, and then does not harm the adhesion of the tiles.
The surface layer of floor tiles is generally smooth, and the surface layer of smooth floor tiles has low water absorption, which will also affect the adhesion of adhesive raw materials. It is true that wall tiles can be applied to the floor tiles, but not all wall tiles are suitable for such practical operation. If you have a small total area of tiles, you don't have to worry too much about those problems, such as just carrying out the renovation and renovation of the floor tiles on the guardrail of the roofIt is okay to use large size floor tiles, because you don't have to worry about the floor tiles falling down, which will cause great harm!
-
Of course not. The effect is very poor and may cause the tile to fade, which may cause injury to others.
-
I think of course you can, as long as you polish the old tiles before pasting, which saves labor and effort and has a good effect.
-
I don't think of course you can't, because the bonding is very poor and it can come off easily.
-
OK. Tile adhesive, also known as ceramic tile adhesive, is mainly used for pasting decorative materials such as tiles, face tiles, floor tiles, etc., and is widely used in interior and exterior walls, grounds, bathrooms, kitchens and other building finishing decoration places. Its main characteristics are high bonding strength, water resistance, freeze-thaw resistance, good aging resistance and convenient construction, which is a very ideal bonding material.
-
Answer can not be directly on the wall, tile glue to get the hand after the need to add an appropriate amount of water for deployment, and put for about 10 minutes before use, if the tile glue is not added to the wall directly on the wall, the later is likely to appear tile cracking and hollowing, will also reduce the adhesive effect of tile glue.
Question: I mean to use tile adhesive and water to stir powder, is it okay for exterior walls?
Q: Is there a difference between the effect and cement sand powder?
Answer: The use of tile adhesive, only need to apply a thin layer, can be a good space-saving, and the use of cement sand powder needs to lay a thick layer, although only a few millimeters or centimeters of the difference, but it generally occupies a larger space, easy to make a small area of space appear narrower when the paving is completed. The use of cement sand powder for the pasting of ceramic tiles is a traditional tiling method, and the tile falling off during use is a common phenomenon, the main reason is that the cement should be pasted with the ceramic tile with a rough surface, porous and high water absorption rate to make it more firm. The tiles, stones, mosaics and other materials sold on the market have extremely high hardness, most of the surface is smooth and flat, and the water absorption rate is very low.
Question: Do you want to mix sand and cement with tile glue powder wall?
-
Nowadays, the use of tile adhesive for decoration work is more extensive, and we often add some tile adhesive to the mixed mortar when painting, which is not only conducive to the ash collection work but also can improve the wall painting, reduce the cracks caused by the heat expansion and contraction of the mixed mortar, and the actual effect of replacing lime powder with tile glue for wall plastering in the room is too high, but the cost is too high. But with a little bit of it's just as productive!
The application of floor tiles on the porcelain wall will greatly ensure the quality and reduce the bulging and peeling conditions that often occur after the floor tiles are paved! Porcelain tiles belong to the mud floor tiles, logically speaking, only need to be solved by making tea before paving, and if the engineering construction is appropriate, even if it is paved with pure cement, there will be no quality problems? Does it have little effect with or without tile adhesive?
However, even if the adhesion of tile adhesive is stronger, the actual effect of applying tile adhesive to pave porcelain tiles will undoubtedly be stronger!
The traditional method of sticking wall tiles is to use concrete. However, it is important to note that concrete can only be bonded to floor tiles with non-smooth, porous structures and high water absorption. At this stage, some mosaic and full-body marble on the market have high strength, smooth surface and low water absorption, so they fall off and become a widespread condition.
Tile adhesive is also in business. Tile adhesive is a formulated adhesive raw material consisting of high-quality concrete, graded sand and polymer additives, which has a strong adhesion force to smooth surfaces.
If you choose a wall tile that is porcelain, non-hygroscopic or has very low water absorption, you need to use tile adhesive. In other words, hygroscopic floor tiles, even if you buy porcelain, do not need to use super glue; And the floor tiles that are not hygroscopic, even if you buy semi-porcelain, you still have to use super glue. For the detection of porcelain or semi-porcelain, you can let the tiles soak in water.
The application of tile adhesive can only be applied when the surface is very neat, and if it is not leveled, it is also necessary to apply manpower to carry out ground leveling such as cement concrete mortar. This not only adds more financial and material resources to the construction of the project, but also endangers the adhesion of tile adhesive if there is a residual dirt layer such as ash layer at the bottom layer after ground leveling.
-
Tile adhesive must be used, because tile adhesive is more adhesive than cement mortar, and the construction is relatively simple, stirred in advance, and can be evenly applied to the wall after standing for 10 minutes.
-
Tile glue should be used on the wall of porcelain tiles; The practicability of tile adhesive is particularly high, with very strong flexibility and adhesion, and waterproof, high temperature resistance, but also space-saving, non-toxic and harmless, but also particularly environmentally friendly.
-
Don't use; Personally, I think the practicality of tile adhesive is very average, because it will effectively increase the cost of decoration, and its viscosity is also very average.
It is not possible to paste the exterior wall bricks from the bottom to the top, but from the top to the bottom, so as to prevent the bricks from falling off if they are not dry.
In winter, you can't stick exterior wall tiles, which are easy to fall off. >>>More
JCDecaux type 2 tile adhesive is mainly pasted with large bricks, 600*600 and 800*800 tiles can be pasted, if more than 800*800 tiles need to be pasted with the use of partners. Tile adhesive is recommended to choose Keshun home waterproof C300 reinforced tile adhesive, the tile adhesive is preferably cement, refined fine aggregate, and added polymer and a variety of special additives to formulate. The product has excellent water retention performance, which is more convenient and faster than traditional cement mortar construction. >>>More
Hello, tile adhesive is a latex adhesive material that can be directly applied to the back of ceramic tiles. Tile adhesive is made of high-quality polymer emulsion material and inorganic silicate, and tile adhesive is usually used in combination with tile adhesive material. Mainly used in the tile without soaking in water, because this tile absorbs less water, after applying a layer of tile adhesive, it is better to stabilize the tile on the wall, tile adhesive is non-polluting, non-toxic, harmless, is a new type of environmental protection material; It can be applied on a variety of material substrates, with strong adhesion ability, water resistance, weather resistance and durability. >>>More
You can choose to paste ordinary porcelain tiles, its use rate is very ordinary, and the hollow drum rate will be very small, as long as the technique is mature when pasting, then there will be no falling off and hollowing the phenomenon, very firm.