What kind of tile will not fall off and be firmly pasted with wall tiles in the living room?

You can choose to paste ordinary porcelain tiles, its use rate is very ordinary, and the hollow drum rate will be very small, as long as the technique is mature when pasting, then there will be no falling off and hollowing the phenomenon, very firm.

Glazed bricks, in the decoration process will not appear to fall off the phenomenon of hollowing, and particularly firm, the quality is particularly good.

Ordinary porcelain tile If the living room wall tile is the use of ordinary porcelain tiles, then relatively speaking, the hollow drum rate will be very little, the construction process is relatively simple, the master paves the porcelain tile is very much, the technical technique is relatively mature, as long as the wall foundation is handled well when paving, normal paving can ensure that it will not fall off.

When decorating the house, many people like to put tiles in the living room, which not only makes it convenient to tidy up the environment, but also makes the living room look especially bright, and advances the overall color of the home. However, because the living room wall tile is different from the intimate tile of the cabinet wall, there is often a hollow drum and falling off, many people think that it is a problem with the tile, in fact, the living room sticks to the wall tile falling off and hollowing, this matter is not very related to the tile, the most important thing is the construction technology of the living room against the wall, what kind of tile has what kind of processing technology, this can be maintained not easy to fall off the hollow drum, and the tile can be solid after pasting.

Method: can not be thick paste, engineering construction soft marble slab tile adhesive usually need to choose thin paste method, thin paste method paving layer thickness is only 1-2cm, because the soft marble tile adhesive water retention characteristics are good, the drying rate is relatively slow, so in the case of the adhesive layer is too thick, the expansion and shrinkage rate of the raw material itself is also expanding, which causes the expansion and convergence index between the adhesive layer and the tile and the wall to be not matched, and the compressive strength of the page fusion is reduced.

Do not add concrete to the soft marble slab tile adhesive. Soft marble tile adhesive was originally a product that has been prepared, immediately mixed with water can be applied, if added concrete or other raw materials, it will completely destroy the scientific and reasonable preparation of soft marble tile adhesive itself, and the middle and late stage of tile paving will occur ceramic tile hollowing, falling off and other potential safety hazards.

Can not be used for caulking, soft marble slab tile adhesive and grout are building materials accessories, but the two have a fundamental difference, soft marble slab tile adhesive can only be used to paste tiles and can not be used as a grout agent to apply. If the soft marble slab tile adhesive is used to carry out the caulking, just block the closing joint of the floor tile, if the floor tile is arched up by heat, it will also be easy to produce the hollowing and falling off of the tile.

The total area of tile adhesive can not be scraped at one time, and the total area of soft marble tile adhesive is too large. Soft marble slabs and tile adhesive projects cannot be scraped at one time, and the total area is very large. The surface of acrylic paint is dry and solid, the outdoor is dry, the wind is strong and other irresistible elements.

Because the total area of scraping is too large, the surface will be dry and solid due to the construction of the project, and then the wall tiles will cause risks such as brick dropping.

For the living room wall tiles, it is possible to use some wall tiles with a relatively flat texture and good quality, so that there will be no falling off and hollowing; If you want to paste it more firmly, you should choose the corresponding method, such as wet pasting, or before pasting the wall tiles, you should first carry out the corresponding bubble bricks, and use tile adhesive with strong viscosity.

You can choose strong installation, you can also choose porcelain tiles, and then choose tile adhesive when pasting, and the cement should be evenly coated.

First of all, the wall should be smoothed out and cleaned so that it can be more firmly pasted.

What kind of tiles will not fall off and hollow the wall tiles in the living room? Nowadays, the interior decoration floor tiles on the wall are more common, the owners of the community in the floor tile area to choose and buy wall tiles, ** business is highly recommended floor tiles on the wall, many interior decoration advanced people, are will choose the floor tiles on the wall, now the interior decoration paste is all high-end floor tiles, especially on the floor tile wall, so that the overall decoration is more luxurious and generous. Choose floor tiles on the wall, and most large living room TV walls choose adhesive floor tiles.

The large living room chooses adhesive floor tiles, and the requirements for tile materials are very high, and not all tiles can be on the wall.

Floor tiles are widely and have low water absorption, and some brands of floor tiles are not hygroscopic, so it is particularly difficult to paste the floor tiles on the wall. The processing technology standard for the pasted floor tile master is very high, because there are many types of ceramic tiles, such as glazed tiles, polished tiles, glazed tiles, antique tiles, full-body marble, mosaic, etc. Suitable for the wall pasted floor tiles, preferred, polished tiles, full-body marble, polished brick texture is particularly good-looking, more suitable for the living room tile wall, full-body marble pasted large living room wall is more high-grade.

The price is also very high.

auxiliary materials for wall tiles; Two years ago, the floor tiles in the large living room were on the wall, and the mixed mortar and auxiliary materials were crushed stone, and the two raw materials were prepared normally, and the adhesive floor tiles were flat and firm. In the case of deviation in the preparation of the two raw materials, it is very easy to produce looseness, hollowing of the wall, half falling, falling bricks and other situations. We all know the net weight of floor tiles, and the occurrence of bulging and falling off poses a safety risk to daily life.

Therefore, the large living room sticking floor tiles has high requirements for auxiliary materials, and the traditional mixed mortar is not suitable for pasting living room tiles.

How to stick it to be firm? Nowadays, the living room decoration is pasted with floor tiles, and the owners of the community can choose the floor tiles on the wall at will. Select the auxiliary materials of the appropriate floor tile material, and stick the floor tile to level and firmly, which is not easy to hollow and fall off the wall.

Because the new adhesive floor tile raw materials are on sale, it replaces the traditional mixed mortar, and completely eliminates the confusion that there is no high-quality special adhesive raw materials in the process of adhesive construction of floor tiles and other materials. Stick floor tiles in the large living room, and apply tile adhesive.

tile adhesives; Tile adhesive, environmentally friendly decorative material. It can be used both inside and outside the room, and is mainly used for sticking floor tiles that are very difficult. The reverse side of the tile is evenly smoothed and the adhesive grout can be carried out to carry out the construction of the project, and the floor tiles can also be pasted on the wall at the same time, water-soluble raw materials, low-carbon and environmental protection.

The walls of the large living room are pasted with floor tiles, and the construction method of two-sided plastering mortar engineering is applied to evenly smooth the wall and the reverse side of the floor tiles with the plastering mortar, and then the wall is pasted.

It should be pasted with glazed bricks, there will be no falling off and hollowing the drum, first of all, the ground should be leveled, so that it will be very firm.

For the living room wall tiles, it is possible to use some wall tiles with a relatively flat texture and good quality, so that there will be no falling off and hollowing; Can not be thick, engineering construction soft marble slab tile adhesive usually need to choose the thin paste method, thin paste method paving layer thickness is only 1-2cm, because the soft marble tile adhesive water retention characteristics are good, the drying rate is relatively slow, so in the case of the adhesive layer is too thick, the expansion and shrinkage rate of the raw material itself is also expanded, which causes the expansion and convergence index between the adhesive layer and the tile and the wall to be not matched, and the compressive strength of the page fusion is reduced.

You can choose a tile with a whole body of marble, and then be sure to choose a tile adhesive when pasting wall tiles, so that the tiles will not be hollow and will not fall off.

The living room is pasted with wall tiles, a full tile, diamond brick, imitation Dali brick.

First of all: look at the firmness of the wall, such as the wall is soft, the mark is low, and the drum is hollow, which should first strengthen the wall in the tile.

2: The wall is firm, which should be brushed with 901 glue on the wall first to prevent the wall from absorbing water too quickly when tiling, causing the tiles to solidify too quickly and fall off.

Three: on the back of the tile on the brush on the adhesive paste, it will be more firm.

Four: After this treatment, it can be paved with special tile cement and cement and coated behind the tile.

Five: the hollow drum is caused by the cement is not coated when the tiles are pasted, and the coating will not cause the hollow drum of the wall tiles.

The use of polished tiles can avoid falling off, which is conducive to choosing the right decoration style. You can use adhesives, or do a good job of tidying the wall and tiling the tiles, which can ensure the firmness of the tiles.

In fact, the living room wall tiles do not have high requirements for wall tiles, and the requirements for construction techniques are relatively high.

All use cement mortar, the tiles pasted, are not ideal, after a few years slowly fall, I don't know what method my husband uses is also cement sand, he sticks the tiles never fall, not drum, not empty, my house! Ceramic tiles for more than 20 years, the tiles are outdated, the tiles can be roughly divided into three categories according to their embryo material and production process, namely porcelain tiles, stoneware tiles, ceramic tiles. In fact, if we don't strictly divide it, there are two categories:

One is some with low water absorption.

The first point is to deal with the wall foundation well, especially if the bottom layer of the bathroom is not treated well, it is easy to fall off. Do a good job of waterproofing, brush on the cement base, brush on a layer of wall solid, paste the tile must be soaked with water, so that the binding force will be the ratio of cement mortar, cement can increase the strength, generally 1 to 3, but in order to increase the strength can also be 1 to 2 or higher, to evenly wipe the mortar on the surface of the brick.

Then there are some masters tile adhesive and ash workability is too large, that is, the ash is thin, the adhesive itself contains glue, dry slowly, after pasting the ash layer slightly down, there is a slight hollow drum in the upper two corners of each piece. It is the brick plastering that causes local gray glazed bricks to generally use C0 grade adhesive, small size vitrified bricks with C1T, large size with C2T, if the wall is a lightweight partition wall, it is best to use C2TES1, if it is a non-traditional base surface, such as glass or metal base surface can be used epoxy adhesive.

Tile adhesive, a new type of decorative material. It can be used both indoors and outdoors, and is mainly used for difficult tiles. The back of the tile is evenly smoothed and bonded mortar, you can carry out construction, you can also directly paste tiles on the wall, water-based materials, green and environmentally friendly, high water absorption tiles If you do not soak in water, you can directly construct the cement, which absorbs too much water, causing the cement mortar to become too dry.

In this way, the viscosity of the cement mortar is reduced, and it is easy to fall down with the cement in the future. If you soak in water for too long, it will cause water absorption.

When you are pasting tiles, you must level them, and then when you paste them, you must be tightly seamless, so that they will not fall off the hollow drum.

To choose the right cement, it is generally better to use No. 325 cement, and the quality is guaranteed.

The mixing ratio of cement and sand is 1:3, the wall bricks should choose sediment, the powder wall and sealing groove should choose medium sand, and the floor tiles should choose coarse sand, and it is very important to choose the right sand.

It is also very important to plan the size of the ground and the size of the bricks, and lay the bricks reasonably.

When decorating, the tiles should be soaked in water in advance to soak out the powder produced in the firing process, so that it is not easy to fall off and hollow when pasting.

When decorating the house, we must choose good cement and sand to carry out, so that it will not fall off easily, and the amount of cement must be enough.