The phenomenon of toilet water seepage, the reason why the toilet is flushed and the ground seeps

The toilet is an important bathroom product in our bathroom, which is not only convenient for our daily life, but also makes the bathroom look more hygienic and clean. Due to the high rate of frequent use, water leakage often occurs, and people do not know how to deal with it. So let's take a look at why the toilet leaks?

How to deal with a leaky toilet?

1. Why does the toilet leak - the quality of the toilet itself.

In order to save costs, some manufacturers on the market will choose inferior materials in production. It causes the water inlet valve and water inlet pipe to crack during injection molding, which affects its sealing, so that the water in the water tank overflows into the toilet through the drain valve when used, causing water leakage.

2. Why does the toilet leak - the mechanism of the water tank accessories interferes with the operation and causes water leakage.

If the waiting float and float rod of the water tank are lowered and affect the reset of the flap, it will cause water leakage. In addition, the float rod is too long and too large, which produces large friction with the water tank wall, which affects the free lifting of the float and will also cause water leakage due to seal failure.

3. Why does the toilet leak - small tank accessories.

Some friends like to miniaturize the toilet tank when they choose the toilet, so they will use the float buoyancy is not enough, especially when the tap water pressure is high, when the water does not pass the float, the water inlet valve can not be closed, resulting in the water constantly flowing into the water tank, from the overflow pipe into the toilet, resulting in water leakage.

4. Why does the toilet leak - the connections of the drain valve are not tightly sealed.

If it is not a one-time formed drain valve, due to the poor sealing of the joint, under the action of water pressure, water will flow from the gap to the toilet through the overflow pipe, causing water leakage. There is also a lift-type inlet valve that can be changed freely, and if the sealing ring is not tightly matched with the pipe wall, water leakage can also occur.

How to deal with a leaky toilet:

1. Check whether the flush switch of the toilet can be reset normally, the plastic flush switch of some flush toilets will occasionally get stuck after being worn for a long time and cannot be restored. It can be reset by repeating the switch a few times. It is also necessary to see whether the rubber gasket of the drain under the ball valve is aged, and if it is aged, it is recommended to replace it in time.

2. Check whether the connection between the spherical float and the water inlet switch of the water tank is loose, if the float is in place, then see if the switch is not closed, so as long as the connection between the float and the water valve switch is tightened, it is recommended to replace it immediately if the rubber ball valve is damaged or aging and causes water leakage.

3. If the toilet tank is leaking, it is basically a problem with the drain valve, you can look at the rubber plug of the outlet of the lower tank, whether there is damage or foreign body blockage and causes the toilet to leak. Also see if the water supply pipe in the lower tank is placed correctly.

Dear, I'm glad to answer for you: the reason why the toilet seeps on the ground as soon as it flushes; The main reasons for the leakage between the toilet base and the floor tile are as follows, one is that the drain is blocked, and the water may overflow from the lower part, and another reason is that the water storage place of the toilet leaks, and the specific treatment methods are as follows: 1. For the toilet, daily maintenance is also very necessary, and the toilet is completed in accordance with the best glass glue to fix the toilet, so as to be more durable.

2. It is best to clean the toilet regularly, and do not move the toilet, and the water storage space of the toilet is best to be cleaned regularly, so that there will be no problems.

1. If there is a leak at the edge of the toilet, it is generally at the bottom of it, mainly because the sealing effect has failed, which is also directly related to the fact that the toilet was not installed when it was installed. For example, if the diameter of the ground drain outlet and the toilet pipe is not completely aligned, it will lead to water leakage at the bottom, and there will be a smell at the same time.

2. Another point is that the flange ring is not installed during installation, or the flange ring is not sealed. Long-term use can cause gaps and loosening between the toilet and the floor, which can lead to water leaks at the edges.

3. When encountering this kind of problem, we first need to disassemble the toilet, and then see at the bottom whether the sealing work is not in place, and then clean the bottom of the toilet bowl and reseal it with sealant. Apply a thick layer of glass glue along the edge of the hole in the floor drain, press the toilet tightly according to the drain, and wipe off the spilled glue along the bottom with a rag.

4. It cannot be used within 24 hours after installation, and it can only be used in the later stage until the glass glue is completely solidified and the sealing work is in place.

5. If it is because of the quality of the toilet, some toilets have been used for a long time, the pressure resistance will drop, and there are cracks, in this case, you can only buy and replace the new toilet.

It is caused by a misalignment between the toilet bowl and the flange (rubber seal) and the sewer pipe, or the sealing ring is misaligned.

Go out and buy a new flange, if you have the ability to do it, move the toilet away, replace it with a new flange, and use something to pad the toilet flat after replacing it, and then you can test the water, so as not to seep out, just hit the glass glue around the toilet base.

If you don't have the ability to do it, you can ask a plumber to get it (ask the store to send someone to get it for you when you buy a flange), and buy a bucket of glass glue, which you pay for money.

Answer reason 1: The inlet valve does not have a filter. If there are too many impurities in the water, it will cause blockage to the sealing ring in the water inlet valve, so that the water inlet valve will not be closed when it is working. Due to the loose sealing of the joint, the water of the non-disposable formed drain valve flows into the toilet through the overflow pipe through the interface gap under the action of water pressure, resulting in water leakage.

If the sealing ring is not tightly matched with the pipe wall, the lifting inlet valve that can change the height freely will often cause reason 3 and the design of the water tank is not good. For example, when the water tank is discharged, the float and the float rod will affect the normal reset of the flap and cause water leakage. In addition, the float rod is too long, and the float is too large, which causes friction between the water tank wall, affects the free lifting of the float, and leads to seal failure and water leakage.

Reason 4: The float in the tank is not buoyant enough. Nowadays, many toilet tanks are small, so that although water can be saved, the buoyancy of the float is not enough, so that the float can not turn off the inlet valve after being flooded, so it leaks. In this case, the float will need to be changed, but before changing, calculate the pressure required by the float, and then choose what kind of float according to this.

Reason 5: Inferior material. Some manufacturers blindly reduce production costs, and choose inferior materials to cause cracking at the outlet of the water inlet valve and the water inlet pipe itself during injection molding, resulting in sealing failure, and the water in the water tank flows into the toilet through the overflow pipe of the drain valve, resulting in "long flowing water".

Water seepage on the edge of the toilet may be due to the fact that the toilet drain is not smooth, and the toilet flange of the toilet is broken, and it is not sealed to cause water seepage.

It means that your toilet waterproofing is not done well, you need to remove the sealant and reinstall it, and the toilet valve seal may seep water, it is recommended that you check it.

If the sewer pipe is blocked or the connection is not connected, recheck it and seal it with that glass glue.

1. Failure to install it during installation: the sewage outlet on the ground is not aligned with the toilet sewage diameter, and the dirty water will leak out.

2. Brother Sou is not well sealed: the toilet flange is not installed or the flange is aging and cracked, and the main Yehong of the toilet flange is used to seal the leakage book to prevent leakage.

3. Loose toilet: caused by long-term use, the toilet and the ground are loose and leaking.

4. Toilet aging: the ceramic cracks inside the toilet are bursting and expanding.