What to do if there is water seepage at the bottom of the toilet, and how to deal with water seepage

When water seeps from the bottom of the toilet, you can use the pull-burst bolt fixing method to solve the problem: place the toilet in the installation position, draw the outline of the toilet base on the ground, and draw the location of the bolt holes in the mounting holes.

Toilet removal begins by unscrewing the connecting tube between the toilet and the wall. Then use a blade to remove the white sealant from the bottom of the toilet that is in contact with the ground, and then remove the toilet.

When installing, first clean the area around the toilet eye, and there should be no sewage. Align the eye of the toilet with the toilet hole on the floor and lay it flat, then lift the toilet left and right, apply a circle of glue to the inside of the toilet, then apply glue to the outside of the toilet and flatten, and use a circle of glue to connect the tube to the wall.

Do not use water after 42 hours of installation. Wait until the glue is dry.

What to do if water seeps at the bottom of the toilet is as follows:

1. If the internal parts of the water tank are aging and cause water seepage at the bottom of the toilet bowl, it is necessary to replace the parts as soon as possible. If there is a problem with the water inlet group and the water outlet group of the toilet, you need to open the water tank and see that the water tank is overflowing, and the water flows out of a water pipe indicates that the water inlet group is broken, and if there is a sound of water inflow, the water outlet group is broken. If the water leaks from the tank, you can take off the drain core and clean up the scale.

After the above problems are removed, if the decoration is not good, it is easy to leak.

2. If it is installed in a specialty store, it is usually padded with a sealing ring inside, and the glass glue around the toilet bowl can be used to prevent water seepage at the bottom of the toilet bowl. Things to prepare: wrench, (if you need to disassemble and install the angle valve, you need to prepare) water adhesive tape, utility knife, glass glue and glass glue gun, toilet special sealing ring (if you need to replace it).

3. If it is a decoration of plumber and electrical tooling, white cement is usually used. Things to prepare: a flathead screwdriver (used to eliminate the original white cement), white cement (when loading from scratch, first mix the water at the bottom of the toilet, then put the toilet seat up and put it steadily, and then use the mixed white cement to seal the toilet footsteps in a circle, and then it can be used when it is dry.)

Be careful not to let the white cement fall into the pipe, otherwise the pipe will be blocked, and the bottom of the flush toilet is also prone to water seepage.

As we all know, it is inevitable that the toilet will seep after being used for a long time. So the question is, how to deal with water seepage on the edge of the toilet base? Let's find out.

First scrape off the glass glue that has failed on the edge of the toilet base, and lift the toilet slightly to check whether the sealing ring of the sewage outlet is damaged or not sealed, if so, we only need to replace the new sealing ring, and finally put glass glue on the edge of the toilet base.

What are the main phenomena of water leakage around the toilet?

1. If the water leaks downstairs near the toilet pipe, there will be water leakage or water seepage marks near the drain pipe, and after the drain pipe is dry, there will be water stains or watermarks.

2. There is also a blackening of the sealant near the toilet base. The main reason for this is the erosion of urine for a long time, and the sealant near the toilet bowl deteriorates very quickly, accompanied by odor. If the toilet bowl is not leaking, the sealant near the toilet bowl will not deteriorate.

How to deal with a leaky toilet.

Normally, the first thing to do when a toilet leaks is to find the specific leak and then prescribe the right medicine. Of course, in order to help you quickly solve the problem of toilet leakage, let me briefly introduce its specific methods for you.

1. Find the water leakage, which can be determined according to experience, or find a special maintenance personnel to deal with it.

2. Take waterproof treatment for toilet drainage, and use waterproof products to seal, such as: glass glue.

3. The drain of the toilet is aligned with the sewer pipe.

4. Seal the toilet base, such as sealant.

5. Wait for half a month to a month or so, if there is no water leakage, it means that the problem has been solved.

Summary: After reading the above introduction, I believe you have a further understanding of how to deal with water seepage at the edge of the toilet base. If you need to know more about it, please continue to ******, and more exciting content will be presented to you in the future.

Repair method of leakage at the bottom of the toilet:

1. The toilet is clogged and causes water leakage

The toilet is clogged with foreign objects and cannot be flushed for a long time, resulting in water leakage at the bottom.

Solution: If the toilet plugs the leakage, you can first unclog the toilet to make the toilet unobstructed, and then make glass glue on the edge of the toilet.

2. The toilet is not installed properly, resulting in water leakage

If the toilet is not properly installed, for example, the toilet flange is not aligned with the drain port, then when flushing, water will overflow.

Solution: Reinstall the toilet, replace the toilet flange, and then put a glass glue interface on the edge of the toilet.

3. The glass glue on the edge of the toilet is damaged

The glass glue around the toilet is damaged, which is easy to deteriorate after a long time, resulting in water leakage.

Solution: Re-apply the glass glue, clean the old glass glue on the bottom edge of the toilet with a blade, and then re-apply the glass glue and wait for 24 hours to use.

4. The toilet parts are damaged

The water tank parts of the toilet are damaged, and the water tank of the toilet floats for a long time and cannot be used for aging.

Solution: To replace the damaged parts, you need to know which part of the toilet is damaged, and then replace it.

Dirt cleaning and maintenance method at the bottom of the toilet:

1. Before cleaning the toilet, open the bathroom window for ventilation and take away the miscellaneous objects on the toilet.

2. Pour toilet cleaner around the inner wall of the toilet, cover the toilet lid and soak for a few minutes.

3. Pour disinfectant on the rag and wipe the water tank, flush button, toilet edge, and toilet washer.

4. Use a paper towel to wipe the area where the toilet has been wiped with disinfectant, and use an old toothbrush to clean the sanitary dead corners that are not easy to clean.

5. Open the lid of the toilet, and Qizhen should use the toilet to scrub the inner wall of the toilet, especially the various outlets inside the toilet, and focus on cleaning.

6. Finally, flush the toilet bowl with clean water, borrow the toilet water flow, and flush the toilet brush, so that the toilet bowl is cleaned.

1.Check the water tank and water pipes: First of all, check whether the water tank and water pipes are rotten for water leakage, and if so, they need to be repaired or replaced in time.

2.Check the gasket: Check that the gasket on the bottom of the toilet is aged or broken, and if so, need to replace it with a new one.

3.Check the screws: Check whether the screws at the bottom of the toilet are loose or missing, and if so, need to tighten or replace the screws.

4.Check the drains: If none of the above solves the problem, you need to check whether the drains are blocked or damaged, and if so, you need to clean or repair the drains.

5.Please ask the professional personnel to repair: if the above methods cannot solve the problem, it is recommended to ask a professional to repair.

Most of the cases are caused by the aging of the internal parts of the toilet tank, at this time it is necessary to replace the parts, if there is a leak in the connection between the toilet and the sewer pipe, the toilet needs to be re-installed and re-sealed.

32% of toilets have dysentery bacilli on them, one of which is called"Song Nei"The dysentery bacilli survive on the toilet seat for up to 17 days; Another experiment also pointed out that when 100 million polioviruses were thrown into the toilet, 3,000 viruses were splashed on the seat. At the same time, many people like to put a flannel gasket on the toilet bowl in winter, which is easier to adsorb, retain and excrete pollutants, and is more likely to spread diseases.

Caused by installation errors or broken flanges.

The specific steps are as follows:

1. The bottom edge is leaking, which may be caused by installation errors or broken flange rings, it is recommended to remove the toilet, reinstall it, or replace the flange ring.

2. If it is caused by the poor sealing of the bottom of the toilet and the floor tiles, that is, the glass glue is opened, it is recommended to remove the old glass glue and re-enter the high-quality glass glue seal.

3. If the bottom of the toilet is cracked and leaking, the crack is not large, it can be filled with colloid, if the crack is large, it is recommended to replace the toilet.

4. Toilet leakage, in addition to the quality of the toilet itself, it is also possible that the quality of the water valve pipe is not good, and it is damaged, causing water leakage. In addition, if the drain valve is not tightly sealed, it will also cause the toilet to leak.

Causes of water leakage:

1. The toilet was not installed properly when it was installed, resulting in the misalignment of the sewage outlet on the ground with the toilet sewage caliber. As a result, water and odors will come out.

2. The toilet installation is not professional, and the flange is not installed.

3. Long-term use causes loosening of the toilet bowl and the ground.

4. The quality of the toilet toilet is problematic, and the ceramic has cracks.

5. The internal parts of the water tank are aging.

6. There is a problem with the water inlet group or outlet group of the toilet.

Solution: If the internal parts of the water tank are aging, you need to replace the parts as soon as possible, if the connection between the toilet and the sewer pipe is leaking, you need to reinstall the toilet and re-seal.

If there is a problem with the water inlet group and the water outlet group of the toilet, you need to open the water tank and see that the water tank is overflowing, and the water flowing out of a water pipe indicates that the water inlet group is broken, and if there is a sound of water ingress, the water outlet group is broken.

If the water tank is leaking, you can take off the drain core and clean the scale. After the above problems are eliminated, it is due to water seepage caused by improper installation:

1. If it is installed in a specialty store, it is usually padded with a sealing ring inside, and the toilet is placed with glass glue around it; [Tools to prepare: utility knife, (if you need to disassemble and assemble the angle valve, you need to prepare) water adhesive tape, wrench, glass glue and glass glue gun. Toilet seals (need to be replaced if removed).

2. If it is a decoration of plumbing and electrical tooling, white cement is usually used; Tools to prepare: flathead screwdriver (used to eliminate the original white cement), white cement (when reloading, first mix the water at the bottom of the toilet, then put the toilet seat on it steadily, and then use the mixed white cement to seal the toilet footsteps in a circle, and then use it when it is dry.)

Be careful not to let the white cement fall into the pipe, otherwise it will cause the pipe to be blocked.

<> "What should I do if water seeps at the connection between the toilet and the ground."

1. First close the water inlet behind the toilet and use the stall to drain the water in the toilet, and then use a utility knife to remove the sealant residue on the bottom and the ground. 2. Then remove the toilet, clean the stagnant water, see if the gasket is damaged, if the gasket is damaged, it needs to be replaced in time. 3. Finally, it is necessary to evenly apply glass glue to the connection between the toilet bowl and the ground, and after processing, it is necessary to wait for 24 hours before using the toilet.

How to deal with a leaky toilet.

First, the material of the toilet and parts is not good.

When the toilet leaks, you should first see the cause of the toilet damage, if the internal parts are damaged, then you should disassemble the toilet tank and replace the damaged accessories. Also carefully look at the outlet of the water valve and the water inlet pipe for cracks, and replace the water inlet valve in time if it is damaged.

Second, the connection of the drain valve is not compact.

The drain valve is an important accessory of the toilet, and when the toilet leaks, it is usually the drain valve that has a problem. When the connection of the drain valve is not completely sealed, water will flow out of the gap under the action of water pressure, resulting in water leakage. It is also possible that the holes are cracked or deformed, which can also cause the toilet to leak.

Solution: If it is a problem with the drain valve, it is not easy to deal with it yourself, you need to ask a professional master to repair it, if the valve is damaged, it is best to replace it with a new one.

3. The toilet bowl and sewer pipe are loose.

When the toilet drains, it needs to be connected to the water pipe, and when the water pipe connection is loose or damaged, it is easy to leak.

Solve the case of Fang Xiao: If there is a problem with the upper and lower pipes, the toilet needs to be reinstalled and sealed to solve the problem fundamentally. If the sewer pipe is damaged, a new one should be purchased for installation.