How to use the new refrigerator How to use the new refrigerator

Precautions before using the new refrigerator:

1. Cleaning before use. The inside and outside of the newly bought refrigerator will be wrapped in a variety of protective films, first remove the protective film, scrub the refrigerator with warm water, especially the inside of the refrigerator must also be scrubbed. If necessary, you can put orange peel or cut a few lemon slices into the refrigerator to eliminate the odor in the refrigerator.

2. Placement. In order to facilitate the heat dissipation of the refrigerator during work, the refrigerator should be placed more than 10 cm away from the wall or furniture, avoid direct sunlight or close to heat sources, and should be placed in a cool and ventilated place.

3. Stand before use. The newly bought refrigerator should not be powered on immediately, and it should be left for more than three hours before it is powered on, because the refrigerated oil is likely to run into the pipeline during the transportation of the refrigerator, and it can be powered on after the refrigeration oil returns to its original position to avoid the compressor being burned out.

4. No-load running-in. After the refrigerator is powered on for the first time, wait for the refrigerator to run to the set temperature before putting the food in, it is best not to put too much food, as long-term full-load work will affect the life of the refrigerator and increase energy consumption.

How to use and maintain the refrigerator:

1. It is recommended to clean the inside of the refrigerator regularly, after a long time of use, the refrigerator will not only have a peculiar smell, but also breed bacteria, affect the preservation of food, and thus affect health, so be sure to clean it regularly.

2. Clean the condenser and compressor of the refrigerator regularly, as dust will affect the heat dissipation of the refrigerator, resulting in the weakening of the refrigeration effect of the refrigerator and the shortening of the service life.

3. Check whether the drain pipe is blocked, if the drain pipe is blocked, the water will leak into the refrigerator, so clean the drain pipe frequently.

4. Avoid distributing the refrigerator with other household appliances, the heat generated by other electrical appliances will increase the burden of the refrigerator, it should be kept away from the heat source, direct sunlight from Biman, so as to reduce the burden of the refrigerator and reduce the power consumption of the refrigerator.

1. After the new refrigerator is purchased, it should be wiped several times with a clean rag, but do not close the door after wiping it clean, and open the door to let the odor inside dissipate before powering it on.

2. After the new refrigerator is carried back, it should be left to stand for a few hours before powering on the test.

3. The refrigerator should be placed in a cool and ventilated position, and a certain amount of space should be left around it to facilitate the ventilation and heat dissipation of the refrigerator and improve its refrigeration efficiency.

4. When the machine is powered on, the temperature setting of the freezer should be adjusted at minus 18 degrees, and the temperature of the refrigerated room should be about 5 degrees. The mechanical thermostat should adjust the size of the digital gear according to the ambient temperature of the season, adjust the smaller digital gear in summer, adjust the middle gear in spring and autumn, and adjust it in the larger digital gear in winter.

5. When the machine is powered on, do not put in the food first, wait for the temperature in the refrigerator to drop and stabilize, and then slowly put in the food after the compressor starts and stops normally, and do not put too much food at one time to avoid overload of the compressor.

6. The food placed in the refrigerator should be sealed and wrapped in a container or food bag to avoid odor caused by mutual odor.

New fridge use:

After the refrigerator is delivered to your home, let it sit for 1-2 hours before turning it on.

Do not place food in the refrigerator, so as not to affect the return machine if there is a problem.

After powering up, set the temperature to a higher level to run.

If the refrigerator is well refrigerated and starts and stops normally, you can gradually put in the food, don't put too much at once.

Gradually adjust the temperature to the desired state.

If there is a problem, contact the after-sales service or shopping mall immediately.

If you have a new refrigerator, you must at least stand for eight hours after removing the packaging of the new refrigerator, etc., and then you can turn on the refrigerator and use it normally.

Place it in your designated location, then keep the bottom in full contact with the ground without shaking, and then store things after two hours of power-on.

In fact, when you buy a refrigerator, there will be a random manual, just take a good look at the manual before using it.

The refrigerator you just bought should be left to stand for 2 to 4 hours before turning it on to avoid oil circuit failure.

The running time of the newly purchased refrigerator should not be too long when it is used for the first time, and it should be carried out intermittently, giving each part of the refrigerator a run-in process, and then running in a small gear or setting the temperature slightly higher. When the outside temperature is lower than 16 degrees, if there is a winter compensation switch, please turn it on, which is to help the refrigerator work. The winter compensation switch is usually located on the side of the thermostat.

In addition, the newly bought refrigerator should be placed in a dry and ventilated place, with a distance of more than 10cm from the wall, and the ground should be flat to facilitate heat dissipation.

Related Notes:

The transportation process of the refrigerator can not be guaranteed to be in a stable position for a long time, may have gone through a relatively long bumpy time, and may even be tilted, at this time the lubricating oil in the refrigerator will flow into the coil of the heat exchanger along the pipeline, and a small amount of lubricating oil will also be poured into the compression cavity of the compressor under the action of bumps and vibrations, so that the refrigerator is easy to cause the refrigerator refrigeration system to be paralyzed after starting, so for the sake of insurance, after the new refrigerator arrives, it should be left for 2 to 4 hours before turning on to avoid oil circuit failure.

The refrigerator should not be overfilled, and there should be room for cold air to penetrate the entire inventory. In addition, the refrigerator should be disinfected regularly. Wipe with dilute bleach water or potassium permanganate water every 3-4 weeks, and clean the refrigerator regularly, including all layers, especially the filter, which is often a place for dirt and germs to accumulate.

The above content refers to: Encyclopedia-refrigerator (a refrigeration equipment that maintains a constant low temperature).

If you buy a new refrigerator at home, you need to know how to use it. How to use the new refrigerator? PChouse will take you to find out.

How to use the new refrigerator correctly:

The newly purchased refrigerator needs to be properly stored for three hours before turning on the power, because the refrigerated oil transported in the refrigerator is likely to run into the pipeline, and the refrigerated oil will reset after 3 hours of resting. At this time, the compressor will not be burned out by re-energizing.

After the refrigerator is powered on, let the refrigerator run to the set temperature before putting the food into the refrigerator, the purpose of this is not to increase the operation of the refrigerator and achieve the purpose of saving electricity.

Turn on the refrigerator after standing, and then turn it on after standing for 2 to 6 hours, after checking that it is correct. In order to avoid oil circuit failure (refrigerator after handling) After the power is turned on, carefully listen to whether the sound of the compressor is normal when starting and running, whether there is the sound of the pipes hitting each other, if the noise is too loud, check whether the product is placed smoothly, and make corresponding adjustments. If there is a loud abnormal sound, you should cut off the power immediately and contact a professional refrigerator repairer.

Here are <> tips for using your new refrigerator:

1. The new refrigerator needs to stand for 2-4 hours.

The compressor to ensure the normal operation of the refrigerator needs some lubricating oil protection, but the refrigerator must be vibrating during transportation, at this time, the lubricating oil of the refrigerator compressor flows into other places, once the power is used, it is inevitable that there will be a failure, so, for the sake of safety, let it stand for a few hours. In addition, during the standing process of the refrigerator, all the doors and drawers of the refrigerator can be opened, ventilated and deodorized, and wiped with a damp rag with light salt water or alkaline water to sterilize, and then it can be officially powered on.

2. Refrigerator location.

First of all, dry and ventilated, no direct sunlight, secondly, the ground should be flat, and finally, the distance from the wall should be more than 10cm, all for the convenience of heat dissipation. The new machine has just arrived, and it is necessary to give it a run-in process and adapt to the process first. It is best to reach the set temperature before putting food in the refrigerator after it is shut down, which is also to ensure that the workload of the refrigerator is not increased.

3. Socket for the new refrigerator.

The circuit problem is the most important place to pay attention to, although the refrigerator is an electrical appliance, but it is different from the general electrical appliances, the current is very large when starting, is 5-10 times that of normal operation, if this time also shares a socket with other electrical appliances, not only the refrigerator is uncomfortable, the socket can not stand it, the result is that the socket is selected short circuit.

Keeping hot food in the refrigerator can lead to wasted electricity and the life of the refrigerator, because hot food releases heat that makes the refrigerator temperature unstable, and the refrigerator uses excess electricity to keep it cold.

Remember to put a layer of plastic wrap on the leftovers on the plate, which is conducive to prolonging the freshness of the food and will not smell with other foods; Fruits should be frozen after wiping the surface moisture, and meats such as fish and pork ribs should be packed in plastic bags and frozen.

Bananas and mangoes should not be put in the refrigerator to freeze, if they are put in the refrigerator, they will speed up their deterioration, and they should be placed in a cool place indoors, and chocolate and honey are not suitable for putting them in the refrigerator.

You can't stuff the refrigerator with things and leave no gaps, this is because the refrigerator needs cold air convection to lower the temperature, and if there is no gap, it will make it difficult for the refrigerator to work normally, which is not conducive to prolonging the life of the refrigerator. Clean the inside and outside of the refrigerator regularly, clean the refrigerator regularly every 3 months or so, take out the contents of the refrigerator, wipe the inside and outside of the refrigerator, clean up the expired things that have been placed in the refrigerator for a long time, prevent contamination of other food, clean the ice in the freezer, and reduce the load on the refrigerator.

How do you smell in a new refrigerator?

1. Put one pound of baking soda powder in two open containers, and put the two containers in the upper and lower layers of the refrigerator. After 24 hours, the refrigerator can remove all kinds of odors, so that the effect of odor removal can be achieved.

2. Use a clean cotton towel, wet a little bit, then wring it out and put it on the top of the refrigerator, and achieve the adsorption effect of the odor inside the refrigerator through the air convection inside the refrigerator. After a period of time, the towel is washed in warm water and can be recycled after exposure to the sun.

3. Use a pound of fresh oranges, wash them with orange peels, and put them in all corners of the refrigerator, so that there will be no peculiar smell after a few days. This method is a little more expensive to remove the flavor of the material, and it cannot be recycled, but the effect of the deodorization is better.

4. Use flower tea to taste, put the flower tea in a cloth bag, 50 grams of it. Then put it in the refrigerator, using the adsorption capacity of the tea leaves, it can remove the odor in the refrigerator in about 24 hours. Expose the tea to the sun once a month, and then you can continue to use it.

Whether at home or at work, the refrigerator should be cleaned regularly, otherwise it will not only smell but also breed bacteria! If you have purchasing needs, you can go to Kelip to buy worry-free.

Take a look, the exclusive platform for enterprise office supplies procurement, backed by Chenguang Group, has strong strength, product quality can be guaranteed, complete categories, has its own distribution chain, and the logistics speed is very fast!

1. When you buy a new refrigerator, first open the door and place the accessories in the inner box. Next, wipe the surface and interior with a clean cloth. After wiping it clean, officially start the refrigerator, adjust the temperature controller to the middle position, plug in the power, and at this time, the light is on.

In order to ensure safety, you should use a test to see if the refrigerator is leaking, if not, continue to operate the refrigerator.

2. Next, close the door of the box, about 5-15 minutes, wait for the temperature in the box to drop to a suitable temperature, and then place the food. Note that the circulating air flow must be formed in the box, and the food should not be piled up too densely, otherwise the air flow will be blocked, which will affect the refrigeration effect. In addition, it is best to leave a gap between the food, with cooked food on top and raw food on the bottom.

Remove as much water as possible from foods that are heavy in water before putting them in. Remember to clean up perishable food regularly, otherwise, it will make the refrigerator smell bad.

3. If you need to refrigerate, you can fill the ice box with boiling water. When making ice, in order to prevent the ice box from freezing together, you should wipe the water at the bottom of the ice box dry, and put a layer of wax paper on it, and then put it on the refrigerator. Under normal circumstances, ice making can be completed in 3-4 hours.

It is important to note that ice is not made for eating, but for making cold drinks. If you swallow ice cubes directly into your stomach, it is easy to "make a stomach".

Proper use of the new refrigerator:

1. First of all, after the refrigerator is bought, be sure to remove the base under the refrigerator, so as to ensure the normal heat dissipation of the refrigerator. If you don't remove it, there will be the following disadvantages: it will affect the heat dissipation of the refrigerator, the refrigerator is easy to pour, easy to pour, there are potential safety hazards, and it is not beautiful.

2. Don't rush to power on after you buy it, because the bumps in the refrigerator after transportation may make the oil in the compressor enter the refrigeration pipeline of the refrigerator, too much oil into the refrigerator pipeline will affect the refrigeration effect of the refrigerator, and the light one will affect the shutdown of the refrigerator, and in serious cases, it will lead to the oil blockage of the refrigerator capillary, so it will not be refrigerated. The refrigerator should be prevented from standing still for more than one hour to ensure that the oil entering the pipeline is returned to the press and then energized for operation.

3. After buying it back, you must wipe the entire room of the refrigerator twice with a clean damp cloth, because the refrigerator is produced on the production line, I don't know how many people have touched it, and I don't know what dirty things will be stained on it, so it's better to wipe it twice with a damp cloth.

4. After the normal use of the refrigerator, try not to put overheated things in, which will easily lead to freezing in the refrigerator, do not think that the freezing indicates that the refrigeration effect of the refrigerator is good, which can only mean that your refrigerator should not have any major problems, but this will affect the refrigeration effect of the refrigerator. Thick ice will cause the surface temperature of the evaporator inside the refrigerator to be too low, which will cause the temperature felt by the thermostat to be too low, so the temperature in the refrigerator will be higher than expected, which is only applicable to the machine-controlled series of refrigerators, not for the electronic control.

5. After taking things, the door of the refrigerator must be well managed, otherwise you will find that your refrigerator may be running all the time, so that the electricity bill will increase.