Does the thick floor tiles affect the floor heating? Does the thickness of the floor tile paving aff

A lot of people will give floor tiles.

Sand paving, does the thickness of floor tile sand affect floor heating, I will explain it to you today.

The thickness of the floor tile sand affects the underfloor heating because:

1. The thicker the sand layer of the water layer, the slower the temperature will penetrate from the ground, and the corresponding heating time will be longer, so it will be more energy-consuming.

2. The thinner the cement sand layer, the faster the temperature penetration of the ground, and the faster the temperature of the indoor space rises.

Does the thick floor tiles affect the floor heating? The floor tiles are thickened, which may affect the floor heating, but will not completely affect the heat of the floor heating, because the floor heating is installed to the ground leveling, and cement mortar is needed in the middle.

Smoothing, according to the intermediate construction process, to determine whether the floor tiles are paved thickly affects the heat dissipation effect.

First, it may affect floor heating.

Reason 1

Home decoration and installation of floor heating, part of the foam plus pipes, as well as backfill 5 cm thick cement mortar, and then paved with floor tiles on it, the thickness is about eight centimeters, like this case, it is indeed thicker, which may affect the heat dissipation of floor heating. Why? The thickness of the foam, together with the heating pipes, the backfill of 5 cm thick cement mortar, and the paving of 8 cm thick floor tiles, these thicknesses together do affect the amount of heat dissipated.

Reason two

We all know that the floor tiles have good thermal conductivity, and there is no radiation in green environmental protection, although the floor tiles have no thickness, but the foam board below.

Backfill 5 cm thick cement mortar, on this part of the thickness, directly affect the heat dissipation of floor heating. In the case of normal heating in the community, it is impossible to achieve the ideal heat dissipation effect, the normal temperature difference may be a few degrees lower, as long as the indoor heating effect can not reach the normal heat, affecting the thermal conductivity and heat dissipation performance of the floor tiles, and the heat dissipation will be slightly slower.

Summary: The thickness of the cement sand layer only affects the length of heating time, as well as the problem of more cores and less power consumption, and the most important thing is that the insulation layer needs to be done, otherwise the thin cement sand layer is not too effective, if the insulation layer is not done, or the insulation material is relatively poor, then the temperature will run away.

will affect. Because the bricks are too thick, it will affect the transfer of heat energy, resulting in slow heating of the floor heating; If floor heating is installed in the room, it is recommended to use wooden flooring, ceramic tiles or more trendy metal series flooring, usually between 1 2cm thick, which is more suitable for floor heating.

The floor tiles are thickened, which may affect the floor heating, but will not completely affect the heat of the floor heating, because the floor heating is installed to the ground leveling, and the cement mortar is needed in the middle.

If the floor tiles are too thick, it will affect the transfer of heat, and the floor heating will heat slowly. If floor heating is installed, it is recommended to lay wooden floors, ceramic tiles or metal floors, which are more popular now, with a general thickness of about 1 2cm, which is suitable for floor heating and heat dissipation.

The thickness of the mortar for floor tiles will definitely affect the heating effect of underfloor heating. Under normal circumstances, the thickness of dry hard ash is generally not more than 50mm.

If it is too thick, of course, it will affect the floor heating effect, and the reason why the floor is not paved is because the thermal conductivity effect of the floor tile is much better than that of the floor, so most people will choose the floor tile when they choose.

There will be an effect, which will affect the transfer of heat. Laying wooden floors on top of underfloor heating, which can cause the planks to crack due to thermal expansion and contraction.

Dear, I'm glad to answer for you, can you still lay floor heating after laying floor tiles? Can't, kiss, underfloor heating is in the tile. After laying the floor tiles, the floor tiles need to be removed before they can be installed.

The working principle of floor heating is to use the entire ground as the main body of heat dissipation, and dissipate heat to ensure the temperature of the space, so it is necessary to remove all the floor tiles and clean up the foreign objects on the ground to avoid debris cutting the floor heating pipe or affecting the laying of floor heating. After that, a layer of insulation board is laid on the floor to prevent heat loss, and a reflective film is laid and fixed with tape. In this way, the cost of dismantling is relatively large, and it is recommended to use radiators and kiss <>

Underfloor heating floors are used for dry environments for a long time. The thicker the floor, the greater the probability of deformation and cracking of the skin, resulting in worse heating effect. Understand the teacher's suggestion, when the floor heating system is heated for the first time after the completion of the floor heating, the basic ground should be heated to 25 first, and then the temperature should be constant for 12-24 hours.

Finally, slowly ramp up the temperature to the desired temperature at a rate of 1 hour, and don't suddenly set it too high. Rapid heating in a short time, the higher the heating temperature, the greater the heat loss, which not only affects the life of the thermal system, but also leads to the deformation of floor heating. After the floor heating is laid, it will involve the secondary leveling of the ground, which cannot be too thick or too thin.

If it is too thick, it will affect the heating effect. If it is too thin, the ground may be hollowed out and cracked, and it will also cause problems with spatial differences.

Because each bricklayer has different requirements for tiles, they are all constructed according to the actual situation of the space, some may require a drop, and some are 3cm. Also, depending on the tiles, marble or floors that the owner buys, the thickness of these materials is different, and the drop is also different. If the living room is a floor tile or room floor, the height of the floor should be increased accordingly, and the floor should be about three centimeters.

Therefore, it is necessary to communicate well in advance when laying floor heating. Leveling with floor tiles is basically to cover the pipe, that is, to cover the pipe. If the floor heating pipe is level, it must be more than three centimeters.

Normal. Let's stick the bricks of the above thickness. Starting from this insulation board, it is two centimeters plus this pipe is, equal, plus this centimeter leveling, plus the lime sand layer, the thickness of the floor tiles is basically eight to ten centimeters.

That is, under normal as-built conditions, the completion is within eight to ten centimeters.

Although these dimensions are professional, the owner should know more about them in advance, so there is no doubt about the later construction, which will avoid some risks. The space of the balcony, kitchen, and bathroom should be deducted. Generally, these two spaces do not do underfloor heating, but a few people do.

There are several cases of underfloor heating in the kitchen. The kitchen area is relatively large, and underfloor heating will be considered. The kitchen may be open.

But usually, there may be some vegetables in the kitchen. If you have warm vegetables, they will not last long and will spoil quickly after a few days. This is a significant drawback.

There was also balcony space. If it is closed and there is a sliding door, it is generally not done. Balcony space is done less, as it also involves energy consumption.

Some people can make toilets, but they should pay attention to waterproofing during construction. Generally, it is necessary to waterproof for the second time, water and electricity for the first time, and floor heating for the second time. Floor heating needs to be discounted on the basis of the internal area of the suite, about 70%, 120 square meters of houses, the area is between 75-80 square meters, and the area of the floor cabinet with cabinets in the room should be deducted.

One square meter**13140, but different materials** are different. For example, the pipe is domestic, imported, ordinary, and can be chosen according to your budget.

Yes, so people generally choose wooden flooring when decorating, so that the heat permeability effect is better.

It will definitely be affected, so you must not choose too thick materials when installing floor tiles.

No. Because the floor tiles will not affect the heating effect, and the heat dissipation of the floor tiles will be very uniform, so the floor tiles are the best choice.

The floor tiles are of standard thickness, and a little thicker will not affect the heating effect, but not too thin. Very thin floors are used for a long time, and underfloor heating will bake cracks in the floor of the home.

When installing floor heating floor tiles, both thin and thick stickers have their own advantages and disadvantages, which need to be selected according to the specific situation.

The advantages of thin stickers are that the construction is simple, the construction speed is fast, and the requirements for the ground are not high, and the construction can be carried out on a thinner base layer. In addition, the thinly pasted tiles and floors are relatively light, and the pressure on the underfloor heating pipes is less, which is not easy to damage the underfloor heating pipes.

However, the lack of cherry blossoms in thin stickers is that tiles and floors are prone to hollowing and cracking, because the bonding strength of thin stickers is low, and they are easily affected by factors such as temperature changes and ground subsidence.

In contrast, the advantage of thick stickers is that the bond strength is high, the tiles and floors are not prone to hollowing, cracking and other problems, and can increase the load-bearing capacity of the ground. However, the disadvantage of thick sticking is that the construction is difficult, a thicker base is required, the construction period is long, and the pressure on the floor heating pipe is larger, and the floor heating pipe is easily damaged.

Therefore, the choice of thin or thick stickers needs to be decided on a case-by-case basis, including the condition of the floor, the arrangement of the floor heating pipes, the weight of the tiles and floors, and other factors. If the ground is relatively flat, the floor heating pipes are reasonably arranged, and the tiles and floors are relatively light, you can choose thin pastes; If the floor is not very smooth, the layout of the floor heating pipes is not very reasonable, and the tiles and floors are heavier, you can choose thick stickers.

Hope the above answers can help you and have a great day!