How to make a stainless steel plate wall in a hotel kitchen?

Make the wood base layer first, and then the stainless steel plate is attached to the wood base layer.

Just paste it with 304 or 206 stainless steel, you can tell the installer.

But it is recommended to only make the wall on the side of the stove, just use it to make the same as the rice of the base cabinet, and do too much waste.

1. The base surface of the stainless steel plate is free of dust and looseness. The loose part can only be constructed after treatment. 2. There shall be no water accumulation on the base surface, and if there is a need to reinforce, the waterproof layer construction can only be carried out after qualification.

3. When the gap of the stainless steel plate exceeds 3, it should be reinforced, and the construction can be carried out only after treatment. 4. The yin and yang angles, the yin angles of the pile façade and the plane, the inner and outer corners of the façade must be made additional layers. 5. In the morning construction, when there is dew on the stainless steel plate and tile surface, the construction should be stopped.

6. In severe winter, the stainless steel plate should be brushed with a base treatment agent.

The decoration process depends on the decoration material, if you are installed with a glossy stainless steel plate, then I recommend that you remove it immediately. Because the glossy stainless steel is very dirty, and it is very difficult to clean, no matter how you wipe it, there are mimeographs. If you use brushed stainless steel (matte), then you can use it first, because this kind of steel plate is widely used in professional kitchens, and if you don't consider aesthetics, it can be used at home.

If you haven't installed stainless steel plates, then I recommend that you still use ceramic tiles, which are easier to coordinate with the rest of the interior and are more in line with the aesthetic habits of the public.

1.The thickness of 304 stainless steel used for the kitchen stainless steel wall is not deformed: it is recommended to use thick stainless steel, conventional products, easy to buy, if it can be thick, it is better, but it is not easy to buy unconventional products.

It is a foreign standard, which is equivalent to China's national standard: 0cr19ni12ti2. The standard of stainless steel for engineering in China: 1Cr18Ni9Ti; Therefore, 304 is much more expensive than domestic stainless steel.

3.Please note that stainless steel is classified according to the same as imported, while domestic is classified according to the content of nickel steel, such as: 1cr cr cr18ni9ti and so on.

4.Conventional products are: thickness is not easy to buy, but thickness is easy to buy.

5.Brushed plate, also known as matte stainless steel plate; Wire drawing is just a process, and it has nothing to do with the type of stainless steel, that is to say, ordinary steel plates can also be made into wire drawing plates.

Copying on the self-study network will hopefully help you.

It is recommended that you find a few merchants to ask.

The 3mm thick stainless steel plate is punched with foreign punching holes, and the hole can be drilled with cutting fluid. The hand-held electric drill is a stainless steel plate drilling method: 1. Select the cobalt drill bit of the hole diameter that needs to be drilled, and screw it into the lock of the hand-held electric drill; 2. Pinch the steel cone with the left hand to locate the drilling point of the stainless steel plate, and shake the hammer with the right hand to smash the concave point; 3. Hold the handle of the electric drill with both hands and start vertically, and rotate at medium and high speed to drill the ideal hole.

There are also pairs of rivets, which are divided into two parts, the thicker section of the hooded rod body has a hole in the middle, and the thinner section of the capped rod body is an interference fit. When riveting, just drive the thin rod into the thick rod and so on.

Cooking is the main work content of the kitchen, and washing and cleaning semi-finished food, steaming, stir-frying, cooking, frying and other labor are in frequent contact with oil and water. Even if there are only good ventilation and smoke exhaust facilities, it is also necessary to clean at any time, therefore, the wall in the kitchen should be easy to clean, heat-resistant, and waterproof, so first of all, we must choose the appropriate materials for the decoration of the kitchen wall. The 8mm specifications and models of stainless steel bolts are M8*25mm, M8*30mm, M8*35mm and so on.

Cooking is the main work content of the kitchen, and washing and cleaning semi-finished food, steaming, stir-frying, cooking, frying and other labor are in frequent contact with oil and water. Even if there are only good ventilation and smoke exhaust facilities, it is also necessary to clean at any time, therefore, the wall in the kitchen should be easy to clean, heat-resistant, and waterproof, so first of all, we must choose the appropriate materials for the decoration of the kitchen wall. CO2 laser cutting has replaced and is replacing some of the traditional cutting process methods, especially the cutting of various non-metallic materials.

It is a rapidly developing and increasingly widely used advanced processing and so on.

If the gap is too large, it will not only affect the appearance, but also affect the sound insulation effect, and the air intake will not keep warm in winter; Of course, the gap is too small, and the wooden door will shrink and swell with moisture, and it will be deformed when it is wet in summer, which will lead to the situation that it is not easy to open and close.

with 914 glue. The two small tubes of this glue, like a toothpaste tube, are squeezed proportionally and mixed evenly. Treat the cement wall base and polish the coating with sandpaper to avoid falling sand on the wall. Glued with 914. Cures after half an hour.

1. It can be achieved by gluing glass; 2. If the stainless steel is thicker, the cement wall behind it does not need to be leveled, and if the stainless steel plate is relatively thin, the back should be painted and leveled; 3. In addition, advertising nails can also be installed; 4. Gypsum lines and gypsum decorative patterns, when fixed, are fast and simple, and the effect is good, and the general use is: gypsum powder for gypsum lines, because it dries quickly, how much is mixed with how much (mixed with water).

I think if you want to nail 8mm stainless steel plate to the wall, we should design it in advance and use professional tools to nail the stainless steel plate to the wall.

The four corners are made of steel nails, with expansion screws, and mirror nails, which the decorator knows, so it is the most reliable.

If you want to use screws, it will affect the intuitive beauty!

Since it is said that it is embedded in the wall, the four sides of the steel plate are treated, and some small edges of 1 cm are folded in the folding shop, and the folded appearance is like a lid.

Gypsum board is nailed to the woodworking board, the base layer of stainless steel is made of 9 centimeter board, and then the stainless steel façade can be made of glass glue, and it should be noted that 10mm gypsum board is used;

The position of the 9 centiboard can also be replaced by mahoganyboard, which is 5 centimetres thicker than gypsum board, in fact, it is better to do so, and there is basically 10mm thick gypsum board on the market, and the thickness of the wooden keel can be controlled, which depends on the factor of how thick the base wants to do.

1. Generally speaking, the cross bar will be made of stainless steel beading, so it will have high brightness, and there will be no obvious boundary like glass at the joint.

2. The stainless steel strip can be directly embedded in the wall, and the shape of the stainless steel strip is U-shaped, and the stainless steel feet on both sides need to be embedded in the wall. Master carpenters can do it.

3. The cost of this process is not very high, you can try it.

Hope it helps.

Yes, but ** is relatively high, and it is recommended not to use stainless steel on the ground, because it will be slippery in case of oil (more slippery than non-slip bricks, even if the stainless steel plate on the ground has potholes).

If the cost is within your budget, of course you can, as you said all with stainless steel plates, it looks neat and comfortable, you can go to Allianz Steel to consult the stainless steel plate.