Will the tile still be hollowed after grouting? How to do tile grouting?

Will the tile still be hollowed after grouting? Floor tiles.

There is also a possibility that there will be wall hollowing after grouting.

Target. There are many parts of the wall tile bulging, such as the wall hollow drum at the edge of the floor tile, the wall hollow drum occurs in the floor tile part, and the wall hollow drum occurs in 2 3 bricks, etc., if the edge wall is hollow, what can be obtained very well with the method of grouting treatment, and the wall hollow drum in other two conditions is useless.

If there is a hollowing of the wall on the edge of the floor tiles, it is necessary to repair it in a way that needs to be done. At this time, a small shovel must be used to break a gap in the gap between the tiles, and then epoxy resin.

The injection is injected into the hollow area of the wall until the hollow area of the wall is filled. This kind of repair method can also be a good protective floor tile detail.

If there is a partial hollow wall of the paved floor tiles, this hollow wall will not harm the electric water heater.

The smoothness of the shower shower is not solved by that choice. However, if the hollow wall will affect daily life, it is necessary to remove the floor tiles with the hollow wall, and then carry out the paving again, pay attention to the same type of floor tiles.

How to do tile grouting? If the area containing 2 3 floor tiles is all due to the condition of hollow walls, then it must be removed and reconstructed.

If the total area of the floor tiles that bulge is very small, a tile adhesive is required.

paste, the resulting stickiness is stronger. And if the hollow area of the wall is very large, only all of them will be smashed and the project will be built again.

tiles on the floor. After paving, we can use a small hammer to gently tap on the surface of the brick and listen to its sound. If you hear the sound of clanging, it means that the floor tiles in this part have a hollow wall, and it is likely to fall down, which is generally a certain safety risk.

Because there are many kinds of hollow floor tiles, but it does not mean that only the hollow drum grouting treatment method of floor tiles will work. The hollow drum grouting treatment method of floor tiles can only be used for the hollowing of the wall at the edge of the floor tiles, which is reasonable. In general, the hollow drum grouting treatment method of floor tiles works, but the premise is that the edge wall is hollow.

Yes. The tiles can be fixed first, and the wall can be fixed as well, so as to prevent hollowing during grouting.

Hello, it is also possible to hollow after grouting. If you do not clean the debris on the surface and floor before applying the tile, the lack of moisture of the tile will also cause hollowing. If the hollow drum range is small, it can be avoided after grouting, but the large-scale hollow drum grouting will not necessarily be effective.

Stir the cement, remove the coarse sand and gravel in the cement, slowly seep the cement down the hollow place, don't worry, and then clean up the cement left on the tile.

There may be a hollow drum, which should be determined according to the specific situation, and some syringes will be used for grouting treatment in general.

Useful. If there is a hollow drum in the corners of the tile, the grouting is very effective, and you only need to pry the corners of the tile open and pour in cement mortar. If the tile is a large area of hollow drum or part of the hollow drum, it is necessary to re-lay the tile according to the situation, and can not be solved by using the method of grouting .

Curing: After the hollow drum is repaired by hollow drum microporous grouting treatment technology, it usually takes 48 hours for the grouting resin to harden, during which it is strictly forbidden to vibrate and step on to repair the grouting hole.

Precautions for floor tile paving.

When laying floor tiles, we should pay attention to their specifications, and choose the appropriate floor tile specifications according to the area of the laying area. If you choose small floor tiles in a large area, it will make the whole space look more crowded. On the contrary, if you use large floor tiles in a small space, then it will give people a sense of incongruity.

The decoration of the living room should give people a comfortable, bright and natural feeling, so it is necessary to choose light-colored floor tiles to decorate. For example, light beige, white, solid color and other types of floor tiles are fine.

According to the difference in the area of the hollow drum, it can be treated differently:

1. Hollow corners.

If you find that there is a hollow drum on the edge of the tile, you can water the part of the hollow drum on the edge (smash the gap between the tiles with a small shovel, and then inject the Bannishi epoxy injection glue into the gap, and the hollow drum will be automatically sucked in until it is filled and solidified), so as to avoid overall replacement.

2. Local hollowing.

A small amount of local hollowing of the tiles on the wall and floor, such as without affecting the stable installation of furniture and appliances such as cabinets, mirror cabinets, showers and water heaters, can not be treated, but if it affects the installation and daily life, it is recommended to knock off the local tiles and re-pave.

Construction Method:

1. Base surface treatment: remove oil, dust and loose matter on the working surface, clean the gaps of the tiles, and ensure that there are no debris and stagnant water.

2. Stirring: Pour the dry powder into a container containing 27% 29% water in a certain proportion, stir at low speed with an electric mixer, stir while pouring the powder until the thick slurry (like paste) with no granulation and precipitation is uniform and free of granulation and precipitation, and then stir for 1 2 minutes before use.

3. Caulking: Use a professional caulking tool to completely press the caulking material into the gap diagonally, and pay attention not to leave it blank. After 10 minutes, wipe off the caulk from the tile surface with a damp sponge or cloth.

4. Cleaning: After the caulking material is dry, use a wrung out wet sponge to clean the surface of the tile.

1. Cement mortar:If the floor tiles.

It's just that there are hollow drums in the corners.

If the phenomenon is to be repaired, it can be repaired by grouting. When repairing, the gap between the hollow drum and the perimeter should be scraped first.

And the filling should be cleaned up, then the cement mortar should be poured into the gap of the hollow drum, and then the floor tiles should be flattened, and finally wait for it to dry naturally. During the pouring process, the hollow drum position should be gently tapped, so that the cement mortar can repair the hollow drum position better.

2. Grouting resin:Inject grout resin material into the gaps in the hollow drum of the tiles, then flatten the floor tiles, and then wait for about 48 hours, and finally wait for them to dry naturally.

It takes about seven days for the tiles to dry completely after hollowing and grouting, and if the temperature is relatively low, the drying time will be extended. The tile should be cured after hollowing and grouting, and no one can walk on it in a short time, nor can it be in direct contact with water.

It takes about seven days for the tiles to dry completely after hollowing and grouting, and if the temperature is relatively low, the drying time will be extended. The tile should be cured after hollowing and grouting, and no one can walk on it in a short time, nor can it be in direct contact with water.

What are the causes of hollow floor tiles.

1) The base layer of the wall or the back of the floor tile is not cleaned, and there are stains or dust debris.

2) The floor tiles are not soaked in water sufficiently.

3) The quality of cement mortar is not up to standard, or the proportion is improper, or the construction bond is not solid.

Is the hollow drum grouting treatment method feasible?

There are many reasons for hollowing out floor tiles, but it doesn't mean that only the hollow drum grouting treatment method for floor tiles is feasible. The hollow drum grouting treatment method of floor tiles is only effective when there is a hollowing phenomenon at the corners of the floor tiles. In general, the hollow drum grout treatment method of floor tiles is feasible, but the premise is that the corners are hollow.

The solution to the hollow drum of floor tiles.

1. Hollow corners. We can directly take the treatment method of grouting and emptying.

2. Local hollowing. Generally speaking, if there is only a partial hollow, but it does not affect the installation or use of furniture and appliances, we can ignore it. However, if it affects the installation and daily life, it is recommended to knock off this part of the tile and re-install it.

3) Large area hollowing. If this is the case, then it is better to re-do the base layer of the wall and then re-apply the tiles.

4) Hollow bulging arch and falling off. If this is the case, it is more serious, we can wait until the floor tiles are completely loose or even fall off, indicating that the cement mortar layer under the tile and the wall base (or ground base) have also loosened "delamination", at this time, you can use a shovel and other tools to clean up the cement mortar layer, reapply the cement mortar and then pave the tile. However, it should be noted that if the tiles are only partially falling off, do not hit the mortar on the foundation surface to prevent the original solid tiles around from being loosened.

If the hollow drum is at the edge of the four corners of the floor tiles, you can use the method of pouring cement slurry, which saves time and effort and does not destroy the floor tiles. If the middle of the floor tile is hollow, then the floor tile should be taken out and re-laid, you can use a suction cup to suck out the floor tile, and then re-pave the hollow drum floor tile according to the specifications. At this time, it is necessary to pry off the entire surface of the tile and re-lay it.

This kind of problem is generally caused by improper construction, and the construction party should be held responsible.

Summary. Hello 1, tile grouting may also be hollow, for the tile hollow drum, want to use the method of grouting to see the position of the tile hollow drum, if it is the corner of the tile hollow drum, you can use grouting to solve, if it is half of the tile to produce hollow drum, with grouting can not be solved.

2. There are many reasons for the hollowing of tiles, if the base layer of the wall or the back of the floor tiles is not cleaned, and there are stains or dust, there may be hollowing; Tiles need to be soaked in water before construction, and if the water is not sufficient, it may also be hollow; Or the cement mortar used is not up to standard, and it will also produce hollowing.

Will the tiles still be hollowing after grouting?

Hello 1, tile grouting may also be hollow, for the tile hollow drum, want to use the method of grouting to see the position of the tile hollow drum, if it is the corner of the tile hollow drum, you can use grouting to solve, if it is a tile of a mountain line half to produce a hollow drum, with grouting can not be solved. 2. There are many reasons for the hollowing of tiles, if the base layer of the wall or the back of the floor tiles is not cleaned, and there are stains or dust, there may be hollowing; Porcelain bricks need to be soaked in water before construction, and if the soaking water is not sufficient, it may also be hollow; Or the cement mortar used is not up to standard, and it will also produce only a group of hollow drums.

I wish you a happy life.